]> Git Repo - linux.git/blob - drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c
iio: imu: st_lsm6dsx: remove set but not used variables 'acc_sensor' and 'gyro_sensor'
[linux.git] / drivers / iio / imu / st_lsm6dsx / st_lsm6dsx_buffer.c
1 /*
2  * STMicroelectronics st_lsm6dsx FIFO buffer library driver
3  *
4  * LSM6DS3/LSM6DS3H/LSM6DSL/LSM6DSM/ISM330DLC: The FIFO buffer can be
5  * configured to store data from gyroscope and accelerometer. Samples are
6  * queued without any tag according to a specific pattern based on
7  * 'FIFO data sets' (6 bytes each):
8  *  - 1st data set is reserved for gyroscope data
9  *  - 2nd data set is reserved for accelerometer data
10  * The FIFO pattern changes depending on the ODRs and decimation factors
11  * assigned to the FIFO data sets. The first sequence of data stored in FIFO
12  * buffer contains the data of all the enabled FIFO data sets
13  * (e.g. Gx, Gy, Gz, Ax, Ay, Az), then data are repeated depending on the
14  * value of the decimation factor and ODR set for each FIFO data set.
15  *
16  * LSM6DSO/LSM6DSOX/ASM330LHH/LSM6DSR: The FIFO buffer can be configured to
17  * store data from gyroscope and accelerometer. Each sample is queued with
18  * a tag (1B) indicating data source (gyroscope, accelerometer, hw timer).
19  *
20  * FIFO supported modes:
21  *  - BYPASS: FIFO disabled
22  *  - CONTINUOUS: FIFO enabled. When the buffer is full, the FIFO index
23  *    restarts from the beginning and the oldest sample is overwritten
24  *
25  * Copyright 2016 STMicroelectronics Inc.
26  *
27  * Lorenzo Bianconi <[email protected]>
28  * Denis Ciocca <[email protected]>
29  *
30  * Licensed under the GPL-2.
31  */
32 #include <linux/module.h>
33 #include <linux/interrupt.h>
34 #include <linux/irq.h>
35 #include <linux/iio/kfifo_buf.h>
36 #include <linux/iio/iio.h>
37 #include <linux/iio/buffer.h>
38 #include <linux/regmap.h>
39 #include <linux/bitfield.h>
40
41 #include <linux/platform_data/st_sensors_pdata.h>
42
43 #include "st_lsm6dsx.h"
44
45 #define ST_LSM6DSX_REG_HLACTIVE_ADDR            0x12
46 #define ST_LSM6DSX_REG_HLACTIVE_MASK            BIT(5)
47 #define ST_LSM6DSX_REG_PP_OD_ADDR               0x12
48 #define ST_LSM6DSX_REG_PP_OD_MASK               BIT(4)
49 #define ST_LSM6DSX_REG_FIFO_MODE_ADDR           0x0a
50 #define ST_LSM6DSX_FIFO_MODE_MASK               GENMASK(2, 0)
51 #define ST_LSM6DSX_FIFO_ODR_MASK                GENMASK(6, 3)
52 #define ST_LSM6DSX_FIFO_EMPTY_MASK              BIT(12)
53 #define ST_LSM6DSX_REG_FIFO_OUTL_ADDR           0x3e
54 #define ST_LSM6DSX_REG_FIFO_OUT_TAG_ADDR        0x78
55 #define ST_LSM6DSX_REG_TS_RESET_ADDR            0x42
56
57 #define ST_LSM6DSX_MAX_FIFO_ODR_VAL             0x08
58
59 #define ST_LSM6DSX_TS_SENSITIVITY               25000UL /* 25us */
60 #define ST_LSM6DSX_TS_RESET_VAL                 0xaa
61
62 struct st_lsm6dsx_decimator_entry {
63         u8 decimator;
64         u8 val;
65 };
66
67 enum st_lsm6dsx_fifo_tag {
68         ST_LSM6DSX_GYRO_TAG = 0x01,
69         ST_LSM6DSX_ACC_TAG = 0x02,
70         ST_LSM6DSX_TS_TAG = 0x04,
71         ST_LSM6DSX_EXT0_TAG = 0x0f,
72         ST_LSM6DSX_EXT1_TAG = 0x10,
73         ST_LSM6DSX_EXT2_TAG = 0x11,
74 };
75
76 static const
77 struct st_lsm6dsx_decimator_entry st_lsm6dsx_decimator_table[] = {
78         {  0, 0x0 },
79         {  1, 0x1 },
80         {  2, 0x2 },
81         {  3, 0x3 },
82         {  4, 0x4 },
83         {  8, 0x5 },
84         { 16, 0x6 },
85         { 32, 0x7 },
86 };
87
88 static int st_lsm6dsx_get_decimator_val(u8 val)
89 {
90         const int max_size = ARRAY_SIZE(st_lsm6dsx_decimator_table);
91         int i;
92
93         for (i = 0; i < max_size; i++)
94                 if (st_lsm6dsx_decimator_table[i].decimator == val)
95                         break;
96
97         return i == max_size ? 0 : st_lsm6dsx_decimator_table[i].val;
98 }
99
100 static void st_lsm6dsx_get_max_min_odr(struct st_lsm6dsx_hw *hw,
101                                        u16 *max_odr, u16 *min_odr)
102 {
103         struct st_lsm6dsx_sensor *sensor;
104         int i;
105
106         *max_odr = 0, *min_odr = ~0;
107         for (i = 0; i < ST_LSM6DSX_ID_MAX; i++) {
108                 if (!hw->iio_devs[i])
109                         continue;
110
111                 sensor = iio_priv(hw->iio_devs[i]);
112
113                 if (!(hw->enable_mask & BIT(sensor->id)))
114                         continue;
115
116                 *max_odr = max_t(u16, *max_odr, sensor->odr);
117                 *min_odr = min_t(u16, *min_odr, sensor->odr);
118         }
119 }
120
121 static int st_lsm6dsx_update_decimators(struct st_lsm6dsx_hw *hw)
122 {
123         u16 max_odr, min_odr, sip = 0, ts_sip = 0;
124         const struct st_lsm6dsx_reg *ts_dec_reg;
125         struct st_lsm6dsx_sensor *sensor;
126         int err = 0, i;
127         u8 data;
128
129         st_lsm6dsx_get_max_min_odr(hw, &max_odr, &min_odr);
130
131         for (i = 0; i < ST_LSM6DSX_ID_MAX; i++) {
132                 const struct st_lsm6dsx_reg *dec_reg;
133
134                 if (!hw->iio_devs[i])
135                         continue;
136
137                 sensor = iio_priv(hw->iio_devs[i]);
138                 /* update fifo decimators and sample in pattern */
139                 if (hw->enable_mask & BIT(sensor->id)) {
140                         sensor->sip = sensor->odr / min_odr;
141                         sensor->decimator = max_odr / sensor->odr;
142                         data = st_lsm6dsx_get_decimator_val(sensor->decimator);
143                 } else {
144                         sensor->sip = 0;
145                         sensor->decimator = 0;
146                         data = 0;
147                 }
148                 ts_sip = max_t(u16, ts_sip, sensor->sip);
149
150                 dec_reg = &hw->settings->decimator[sensor->id];
151                 if (dec_reg->addr) {
152                         int val = ST_LSM6DSX_SHIFT_VAL(data, dec_reg->mask);
153
154                         err = st_lsm6dsx_update_bits_locked(hw, dec_reg->addr,
155                                                             dec_reg->mask,
156                                                             val);
157                         if (err < 0)
158                                 return err;
159                 }
160                 sip += sensor->sip;
161         }
162         hw->sip = sip + ts_sip;
163         hw->ts_sip = ts_sip;
164
165         /*
166          * update hw ts decimator if necessary. Decimator for hw timestamp
167          * is always 1 or 0 in order to have a ts sample for each data
168          * sample in FIFO
169          */
170         ts_dec_reg = &hw->settings->ts_settings.decimator;
171         if (ts_dec_reg->addr) {
172                 int val, ts_dec = !!hw->ts_sip;
173
174                 val = ST_LSM6DSX_SHIFT_VAL(ts_dec, ts_dec_reg->mask);
175                 err = st_lsm6dsx_update_bits_locked(hw, ts_dec_reg->addr,
176                                                     ts_dec_reg->mask, val);
177         }
178         return err;
179 }
180
181 int st_lsm6dsx_set_fifo_mode(struct st_lsm6dsx_hw *hw,
182                              enum st_lsm6dsx_fifo_mode fifo_mode)
183 {
184         unsigned int data;
185         int err;
186
187         data = FIELD_PREP(ST_LSM6DSX_FIFO_MODE_MASK, fifo_mode);
188         err = st_lsm6dsx_update_bits_locked(hw, ST_LSM6DSX_REG_FIFO_MODE_ADDR,
189                                             ST_LSM6DSX_FIFO_MODE_MASK, data);
190         if (err < 0)
191                 return err;
192
193         hw->fifo_mode = fifo_mode;
194
195         return 0;
196 }
197
198 static int st_lsm6dsx_set_fifo_odr(struct st_lsm6dsx_sensor *sensor,
199                                    bool enable)
200 {
201         struct st_lsm6dsx_hw *hw = sensor->hw;
202         const struct st_lsm6dsx_reg *batch_reg;
203         u8 data;
204
205         batch_reg = &hw->settings->batch[sensor->id];
206         if (batch_reg->addr) {
207                 int val;
208
209                 if (enable) {
210                         int err;
211
212                         err = st_lsm6dsx_check_odr(sensor, sensor->odr,
213                                                    &data);
214                         if (err < 0)
215                                 return err;
216                 } else {
217                         data = 0;
218                 }
219                 val = ST_LSM6DSX_SHIFT_VAL(data, batch_reg->mask);
220                 return st_lsm6dsx_update_bits_locked(hw, batch_reg->addr,
221                                                      batch_reg->mask, val);
222         } else {
223                 data = hw->enable_mask ? ST_LSM6DSX_MAX_FIFO_ODR_VAL : 0;
224                 return st_lsm6dsx_update_bits_locked(hw,
225                                         ST_LSM6DSX_REG_FIFO_MODE_ADDR,
226                                         ST_LSM6DSX_FIFO_ODR_MASK,
227                                         FIELD_PREP(ST_LSM6DSX_FIFO_ODR_MASK,
228                                                    data));
229         }
230 }
231
232 int st_lsm6dsx_update_watermark(struct st_lsm6dsx_sensor *sensor, u16 watermark)
233 {
234         u16 fifo_watermark = ~0, cur_watermark, fifo_th_mask;
235         struct st_lsm6dsx_hw *hw = sensor->hw;
236         struct st_lsm6dsx_sensor *cur_sensor;
237         int i, err, data;
238         __le16 wdata;
239
240         if (!hw->sip)
241                 return 0;
242
243         for (i = 0; i < ST_LSM6DSX_ID_MAX; i++) {
244                 if (!hw->iio_devs[i])
245                         continue;
246
247                 cur_sensor = iio_priv(hw->iio_devs[i]);
248
249                 if (!(hw->enable_mask & BIT(cur_sensor->id)))
250                         continue;
251
252                 cur_watermark = (cur_sensor == sensor) ? watermark
253                                                        : cur_sensor->watermark;
254
255                 fifo_watermark = min_t(u16, fifo_watermark, cur_watermark);
256         }
257
258         fifo_watermark = max_t(u16, fifo_watermark, hw->sip);
259         fifo_watermark = (fifo_watermark / hw->sip) * hw->sip;
260         fifo_watermark = fifo_watermark * hw->settings->fifo_ops.th_wl;
261
262         mutex_lock(&hw->page_lock);
263         err = regmap_read(hw->regmap, hw->settings->fifo_ops.fifo_th.addr + 1,
264                           &data);
265         if (err < 0)
266                 goto out;
267
268         fifo_th_mask = hw->settings->fifo_ops.fifo_th.mask;
269         fifo_watermark = ((data << 8) & ~fifo_th_mask) |
270                          (fifo_watermark & fifo_th_mask);
271
272         wdata = cpu_to_le16(fifo_watermark);
273         err = regmap_bulk_write(hw->regmap,
274                                 hw->settings->fifo_ops.fifo_th.addr,
275                                 &wdata, sizeof(wdata));
276 out:
277         mutex_unlock(&hw->page_lock);
278         return err;
279 }
280
281 static int st_lsm6dsx_reset_hw_ts(struct st_lsm6dsx_hw *hw)
282 {
283         struct st_lsm6dsx_sensor *sensor;
284         int i, err;
285
286         /* reset hw ts counter */
287         err = st_lsm6dsx_write_locked(hw, ST_LSM6DSX_REG_TS_RESET_ADDR,
288                                       ST_LSM6DSX_TS_RESET_VAL);
289         if (err < 0)
290                 return err;
291
292         for (i = 0; i < ST_LSM6DSX_ID_MAX; i++) {
293                 if (!hw->iio_devs[i])
294                         continue;
295
296                 sensor = iio_priv(hw->iio_devs[i]);
297                 /*
298                  * store enable buffer timestamp as reference for
299                  * hw timestamp
300                  */
301                 sensor->ts_ref = iio_get_time_ns(hw->iio_devs[i]);
302         }
303         return 0;
304 }
305
306 /*
307  * Set max bulk read to ST_LSM6DSX_MAX_WORD_LEN/ST_LSM6DSX_MAX_TAGGED_WORD_LEN
308  * in order to avoid a kmalloc for each bus access
309  */
310 static inline int st_lsm6dsx_read_block(struct st_lsm6dsx_hw *hw, u8 addr,
311                                         u8 *data, unsigned int data_len,
312                                         unsigned int max_word_len)
313 {
314         unsigned int word_len, read_len = 0;
315         int err;
316
317         while (read_len < data_len) {
318                 word_len = min_t(unsigned int, data_len - read_len,
319                                  max_word_len);
320                 err = st_lsm6dsx_read_locked(hw, addr, data + read_len,
321                                              word_len);
322                 if (err < 0)
323                         return err;
324                 read_len += word_len;
325         }
326         return 0;
327 }
328
329 #define ST_LSM6DSX_IIO_BUFF_SIZE        (ALIGN(ST_LSM6DSX_SAMPLE_SIZE, \
330                                                sizeof(s64)) + sizeof(s64))
331 /**
332  * st_lsm6dsx_read_fifo() - hw FIFO read routine
333  * @hw: Pointer to instance of struct st_lsm6dsx_hw.
334  *
335  * Read samples from the hw FIFO and push them to IIO buffers.
336  *
337  * Return: Number of bytes read from the FIFO
338  */
339 int st_lsm6dsx_read_fifo(struct st_lsm6dsx_hw *hw)
340 {
341         u16 fifo_len, pattern_len = hw->sip * ST_LSM6DSX_SAMPLE_SIZE;
342         u16 fifo_diff_mask = hw->settings->fifo_ops.fifo_diff.mask;
343         int err, acc_sip, gyro_sip, ts_sip, read_len, offset;
344         struct st_lsm6dsx_sensor *acc_sensor, *gyro_sensor;
345         u8 gyro_buff[ST_LSM6DSX_IIO_BUFF_SIZE];
346         u8 acc_buff[ST_LSM6DSX_IIO_BUFF_SIZE];
347         bool reset_ts = false;
348         __le16 fifo_status;
349         s64 ts = 0;
350
351         err = st_lsm6dsx_read_locked(hw,
352                                      hw->settings->fifo_ops.fifo_diff.addr,
353                                      &fifo_status, sizeof(fifo_status));
354         if (err < 0) {
355                 dev_err(hw->dev, "failed to read fifo status (err=%d)\n",
356                         err);
357                 return err;
358         }
359
360         if (fifo_status & cpu_to_le16(ST_LSM6DSX_FIFO_EMPTY_MASK))
361                 return 0;
362
363         fifo_len = (le16_to_cpu(fifo_status) & fifo_diff_mask) *
364                    ST_LSM6DSX_CHAN_SIZE;
365         fifo_len = (fifo_len / pattern_len) * pattern_len;
366
367         acc_sensor = iio_priv(hw->iio_devs[ST_LSM6DSX_ID_ACC]);
368         gyro_sensor = iio_priv(hw->iio_devs[ST_LSM6DSX_ID_GYRO]);
369
370         for (read_len = 0; read_len < fifo_len; read_len += pattern_len) {
371                 err = st_lsm6dsx_read_block(hw, ST_LSM6DSX_REG_FIFO_OUTL_ADDR,
372                                             hw->buff, pattern_len,
373                                             ST_LSM6DSX_MAX_WORD_LEN);
374                 if (err < 0) {
375                         dev_err(hw->dev,
376                                 "failed to read pattern from fifo (err=%d)\n",
377                                 err);
378                         return err;
379                 }
380
381                 /*
382                  * Data are written to the FIFO with a specific pattern
383                  * depending on the configured ODRs. The first sequence of data
384                  * stored in FIFO contains the data of all enabled sensors
385                  * (e.g. Gx, Gy, Gz, Ax, Ay, Az, Ts), then data are repeated
386                  * depending on the value of the decimation factor set for each
387                  * sensor.
388                  *
389                  * Supposing the FIFO is storing data from gyroscope and
390                  * accelerometer at different ODRs:
391                  *   - gyroscope ODR = 208Hz, accelerometer ODR = 104Hz
392                  * Since the gyroscope ODR is twice the accelerometer one, the
393                  * following pattern is repeated every 9 samples:
394                  *   - Gx, Gy, Gz, Ax, Ay, Az, Ts, Gx, Gy, Gz, Ts, Gx, ..
395                  */
396                 gyro_sip = gyro_sensor->sip;
397                 acc_sip = acc_sensor->sip;
398                 ts_sip = hw->ts_sip;
399                 offset = 0;
400
401                 while (acc_sip > 0 || gyro_sip > 0) {
402                         if (gyro_sip > 0) {
403                                 memcpy(gyro_buff, &hw->buff[offset],
404                                        ST_LSM6DSX_SAMPLE_SIZE);
405                                 offset += ST_LSM6DSX_SAMPLE_SIZE;
406                         }
407                         if (acc_sip > 0) {
408                                 memcpy(acc_buff, &hw->buff[offset],
409                                        ST_LSM6DSX_SAMPLE_SIZE);
410                                 offset += ST_LSM6DSX_SAMPLE_SIZE;
411                         }
412
413                         if (ts_sip-- > 0) {
414                                 u8 data[ST_LSM6DSX_SAMPLE_SIZE];
415
416                                 memcpy(data, &hw->buff[offset], sizeof(data));
417                                 /*
418                                  * hw timestamp is 3B long and it is stored
419                                  * in FIFO using 6B as 4th FIFO data set
420                                  * according to this schema:
421                                  * B0 = ts[15:8], B1 = ts[23:16], B3 = ts[7:0]
422                                  */
423                                 ts = data[1] << 16 | data[0] << 8 | data[3];
424                                 /*
425                                  * check if hw timestamp engine is going to
426                                  * reset (the sensor generates an interrupt
427                                  * to signal the hw timestamp will reset in
428                                  * 1.638s)
429                                  */
430                                 if (!reset_ts && ts >= 0xff0000)
431                                         reset_ts = true;
432                                 ts *= ST_LSM6DSX_TS_SENSITIVITY;
433
434                                 offset += ST_LSM6DSX_SAMPLE_SIZE;
435                         }
436
437                         if (gyro_sip-- > 0)
438                                 iio_push_to_buffers_with_timestamp(
439                                         hw->iio_devs[ST_LSM6DSX_ID_GYRO],
440                                         gyro_buff, gyro_sensor->ts_ref + ts);
441                         if (acc_sip-- > 0)
442                                 iio_push_to_buffers_with_timestamp(
443                                         hw->iio_devs[ST_LSM6DSX_ID_ACC],
444                                         acc_buff, acc_sensor->ts_ref + ts);
445                 }
446         }
447
448         if (unlikely(reset_ts)) {
449                 err = st_lsm6dsx_reset_hw_ts(hw);
450                 if (err < 0) {
451                         dev_err(hw->dev, "failed to reset hw ts (err=%d)\n",
452                                 err);
453                         return err;
454                 }
455         }
456         return read_len;
457 }
458
459 static int
460 st_lsm6dsx_push_tagged_data(struct st_lsm6dsx_hw *hw, u8 tag,
461                             u8 *data, s64 ts)
462 {
463         struct st_lsm6dsx_sensor *sensor;
464         struct iio_dev *iio_dev;
465
466         /*
467          * EXT_TAG are managed in FIFO fashion so ST_LSM6DSX_EXT0_TAG
468          * corresponds to the first enabled channel, ST_LSM6DSX_EXT1_TAG
469          * to the second one and ST_LSM6DSX_EXT2_TAG to the last enabled
470          * channel
471          */
472         switch (tag) {
473         case ST_LSM6DSX_GYRO_TAG:
474                 iio_dev = hw->iio_devs[ST_LSM6DSX_ID_GYRO];
475                 break;
476         case ST_LSM6DSX_ACC_TAG:
477                 iio_dev = hw->iio_devs[ST_LSM6DSX_ID_ACC];
478                 break;
479         case ST_LSM6DSX_EXT0_TAG:
480                 if (hw->enable_mask & BIT(ST_LSM6DSX_ID_EXT0))
481                         iio_dev = hw->iio_devs[ST_LSM6DSX_ID_EXT0];
482                 else if (hw->enable_mask & BIT(ST_LSM6DSX_ID_EXT1))
483                         iio_dev = hw->iio_devs[ST_LSM6DSX_ID_EXT1];
484                 else
485                         iio_dev = hw->iio_devs[ST_LSM6DSX_ID_EXT2];
486                 break;
487         case ST_LSM6DSX_EXT1_TAG:
488                 if ((hw->enable_mask & BIT(ST_LSM6DSX_ID_EXT0)) &&
489                     (hw->enable_mask & BIT(ST_LSM6DSX_ID_EXT1)))
490                         iio_dev = hw->iio_devs[ST_LSM6DSX_ID_EXT1];
491                 else
492                         iio_dev = hw->iio_devs[ST_LSM6DSX_ID_EXT2];
493                 break;
494         case ST_LSM6DSX_EXT2_TAG:
495                 iio_dev = hw->iio_devs[ST_LSM6DSX_ID_EXT2];
496                 break;
497         default:
498                 return -EINVAL;
499         }
500
501         sensor = iio_priv(iio_dev);
502         iio_push_to_buffers_with_timestamp(iio_dev, data,
503                                            ts + sensor->ts_ref);
504
505         return 0;
506 }
507
508 /**
509  * st_lsm6dsx_read_tagged_fifo() - tagged hw FIFO read routine
510  * @hw: Pointer to instance of struct st_lsm6dsx_hw.
511  *
512  * Read samples from the hw FIFO and push them to IIO buffers.
513  *
514  * Return: Number of bytes read from the FIFO
515  */
516 int st_lsm6dsx_read_tagged_fifo(struct st_lsm6dsx_hw *hw)
517 {
518         u16 pattern_len = hw->sip * ST_LSM6DSX_TAGGED_SAMPLE_SIZE;
519         u16 fifo_len, fifo_diff_mask;
520         u8 iio_buff[ST_LSM6DSX_IIO_BUFF_SIZE], tag;
521         bool reset_ts = false;
522         int i, err, read_len;
523         __le16 fifo_status;
524         s64 ts = 0;
525
526         err = st_lsm6dsx_read_locked(hw,
527                                      hw->settings->fifo_ops.fifo_diff.addr,
528                                      &fifo_status, sizeof(fifo_status));
529         if (err < 0) {
530                 dev_err(hw->dev, "failed to read fifo status (err=%d)\n",
531                         err);
532                 return err;
533         }
534
535         fifo_diff_mask = hw->settings->fifo_ops.fifo_diff.mask;
536         fifo_len = (le16_to_cpu(fifo_status) & fifo_diff_mask) *
537                    ST_LSM6DSX_TAGGED_SAMPLE_SIZE;
538         if (!fifo_len)
539                 return 0;
540
541         for (read_len = 0; read_len < fifo_len; read_len += pattern_len) {
542                 err = st_lsm6dsx_read_block(hw,
543                                             ST_LSM6DSX_REG_FIFO_OUT_TAG_ADDR,
544                                             hw->buff, pattern_len,
545                                             ST_LSM6DSX_MAX_TAGGED_WORD_LEN);
546                 if (err < 0) {
547                         dev_err(hw->dev,
548                                 "failed to read pattern from fifo (err=%d)\n",
549                                 err);
550                         return err;
551                 }
552
553                 for (i = 0; i < pattern_len;
554                      i += ST_LSM6DSX_TAGGED_SAMPLE_SIZE) {
555                         memcpy(iio_buff, &hw->buff[i + ST_LSM6DSX_TAG_SIZE],
556                                ST_LSM6DSX_SAMPLE_SIZE);
557
558                         tag = hw->buff[i] >> 3;
559                         if (tag == ST_LSM6DSX_TS_TAG) {
560                                 /*
561                                  * hw timestamp is 4B long and it is stored
562                                  * in FIFO according to this schema:
563                                  * B0 = ts[7:0], B1 = ts[15:8], B2 = ts[23:16],
564                                  * B3 = ts[31:24]
565                                  */
566                                 ts = le32_to_cpu(*((__le32 *)iio_buff));
567                                 /*
568                                  * check if hw timestamp engine is going to
569                                  * reset (the sensor generates an interrupt
570                                  * to signal the hw timestamp will reset in
571                                  * 1.638s)
572                                  */
573                                 if (!reset_ts && ts >= 0xffff0000)
574                                         reset_ts = true;
575                                 ts *= ST_LSM6DSX_TS_SENSITIVITY;
576                         } else {
577                                 st_lsm6dsx_push_tagged_data(hw, tag, iio_buff,
578                                                             ts);
579                         }
580                 }
581         }
582
583         if (unlikely(reset_ts)) {
584                 err = st_lsm6dsx_reset_hw_ts(hw);
585                 if (err < 0)
586                         return err;
587         }
588         return read_len;
589 }
590
591 int st_lsm6dsx_flush_fifo(struct st_lsm6dsx_hw *hw)
592 {
593         int err;
594
595         mutex_lock(&hw->fifo_lock);
596
597         hw->settings->fifo_ops.read_fifo(hw);
598         err = st_lsm6dsx_set_fifo_mode(hw, ST_LSM6DSX_FIFO_BYPASS);
599
600         mutex_unlock(&hw->fifo_lock);
601
602         return err;
603 }
604
605 static int st_lsm6dsx_update_fifo(struct iio_dev *iio_dev, bool enable)
606 {
607         struct st_lsm6dsx_sensor *sensor = iio_priv(iio_dev);
608         struct st_lsm6dsx_hw *hw = sensor->hw;
609         int err;
610
611         mutex_lock(&hw->conf_lock);
612
613         if (hw->fifo_mode != ST_LSM6DSX_FIFO_BYPASS) {
614                 err = st_lsm6dsx_flush_fifo(hw);
615                 if (err < 0)
616                         goto out;
617         }
618
619         if (sensor->id == ST_LSM6DSX_ID_EXT0 ||
620             sensor->id == ST_LSM6DSX_ID_EXT1 ||
621             sensor->id == ST_LSM6DSX_ID_EXT2) {
622                 err = st_lsm6dsx_shub_set_enable(sensor, enable);
623                 if (err < 0)
624                         goto out;
625         } else {
626                 err = st_lsm6dsx_sensor_set_enable(sensor, enable);
627                 if (err < 0)
628                         goto out;
629
630                 err = st_lsm6dsx_set_fifo_odr(sensor, enable);
631                 if (err < 0)
632                         goto out;
633         }
634
635         err = st_lsm6dsx_update_decimators(hw);
636         if (err < 0)
637                 goto out;
638
639         err = st_lsm6dsx_update_watermark(sensor, sensor->watermark);
640         if (err < 0)
641                 goto out;
642
643         if (hw->enable_mask) {
644                 /* reset hw ts counter */
645                 err = st_lsm6dsx_reset_hw_ts(hw);
646                 if (err < 0)
647                         goto out;
648
649                 err = st_lsm6dsx_set_fifo_mode(hw, ST_LSM6DSX_FIFO_CONT);
650         }
651
652 out:
653         mutex_unlock(&hw->conf_lock);
654
655         return err;
656 }
657
658 static irqreturn_t st_lsm6dsx_handler_irq(int irq, void *private)
659 {
660         struct st_lsm6dsx_hw *hw = private;
661
662         return hw->sip > 0 ? IRQ_WAKE_THREAD : IRQ_NONE;
663 }
664
665 static irqreturn_t st_lsm6dsx_handler_thread(int irq, void *private)
666 {
667         struct st_lsm6dsx_hw *hw = private;
668         int count;
669
670         mutex_lock(&hw->fifo_lock);
671         count = hw->settings->fifo_ops.read_fifo(hw);
672         mutex_unlock(&hw->fifo_lock);
673
674         return !count ? IRQ_NONE : IRQ_HANDLED;
675 }
676
677 static int st_lsm6dsx_buffer_preenable(struct iio_dev *iio_dev)
678 {
679         return st_lsm6dsx_update_fifo(iio_dev, true);
680 }
681
682 static int st_lsm6dsx_buffer_postdisable(struct iio_dev *iio_dev)
683 {
684         return st_lsm6dsx_update_fifo(iio_dev, false);
685 }
686
687 static const struct iio_buffer_setup_ops st_lsm6dsx_buffer_ops = {
688         .preenable = st_lsm6dsx_buffer_preenable,
689         .postdisable = st_lsm6dsx_buffer_postdisable,
690 };
691
692 int st_lsm6dsx_fifo_setup(struct st_lsm6dsx_hw *hw)
693 {
694         struct device_node *np = hw->dev->of_node;
695         struct st_sensors_platform_data *pdata;
696         struct iio_buffer *buffer;
697         unsigned long irq_type;
698         bool irq_active_low;
699         int i, err;
700
701         irq_type = irqd_get_trigger_type(irq_get_irq_data(hw->irq));
702
703         switch (irq_type) {
704         case IRQF_TRIGGER_HIGH:
705         case IRQF_TRIGGER_RISING:
706                 irq_active_low = false;
707                 break;
708         case IRQF_TRIGGER_LOW:
709         case IRQF_TRIGGER_FALLING:
710                 irq_active_low = true;
711                 break;
712         default:
713                 dev_info(hw->dev, "mode %lx unsupported\n", irq_type);
714                 return -EINVAL;
715         }
716
717         err = regmap_update_bits(hw->regmap, ST_LSM6DSX_REG_HLACTIVE_ADDR,
718                                  ST_LSM6DSX_REG_HLACTIVE_MASK,
719                                  FIELD_PREP(ST_LSM6DSX_REG_HLACTIVE_MASK,
720                                             irq_active_low));
721         if (err < 0)
722                 return err;
723
724         pdata = (struct st_sensors_platform_data *)hw->dev->platform_data;
725         if ((np && of_property_read_bool(np, "drive-open-drain")) ||
726             (pdata && pdata->open_drain)) {
727                 err = regmap_update_bits(hw->regmap, ST_LSM6DSX_REG_PP_OD_ADDR,
728                                          ST_LSM6DSX_REG_PP_OD_MASK,
729                                          FIELD_PREP(ST_LSM6DSX_REG_PP_OD_MASK,
730                                                     1));
731                 if (err < 0)
732                         return err;
733
734                 irq_type |= IRQF_SHARED;
735         }
736
737         err = devm_request_threaded_irq(hw->dev, hw->irq,
738                                         st_lsm6dsx_handler_irq,
739                                         st_lsm6dsx_handler_thread,
740                                         irq_type | IRQF_ONESHOT,
741                                         "lsm6dsx", hw);
742         if (err) {
743                 dev_err(hw->dev, "failed to request trigger irq %d\n",
744                         hw->irq);
745                 return err;
746         }
747
748         for (i = 0; i < ST_LSM6DSX_ID_MAX; i++) {
749                 if (!hw->iio_devs[i])
750                         continue;
751
752                 buffer = devm_iio_kfifo_allocate(hw->dev);
753                 if (!buffer)
754                         return -ENOMEM;
755
756                 iio_device_attach_buffer(hw->iio_devs[i], buffer);
757                 hw->iio_devs[i]->modes |= INDIO_BUFFER_SOFTWARE;
758                 hw->iio_devs[i]->setup_ops = &st_lsm6dsx_buffer_ops;
759         }
760
761         return 0;
762 }
This page took 0.082003 seconds and 4 git commands to generate.