[linux.git] / drivers / scsi / dtc.c


#define AUTOSENSE
#define PSEUDO_DMA
#define DONT_USE_INTR
#define UNSAFE			/* Leave interrupts enabled during pseudo-dma I/O */
#define xNDEBUG (NDEBUG_INTR+NDEBUG_RESELECTION+\
		 NDEBUG_SELECTION+NDEBUG_ARBITRATION)
#define DMA_WORKS_RIGHT


/*
 * DTC 3180/3280 driver, by
 *	Ray Van Tassle	[email protected]
 *
 *	taken from ...
 *	Trantor T128/T128F/T228 driver by...
 *
 * 	Drew Eckhardt
 *	Visionary Computing
 *	(Unix and Linux consulting and custom programming)
 *	[email protected]
 *      +1 (303) 440-4894
 *
 * DISTRIBUTION RELEASE 1.
 *
 * For more information, please consult 
 *
 * NCR 5380 Family
 * SCSI Protocol Controller
 * Databook
*/

/*
 * Options : 
 * AUTOSENSE - if defined, REQUEST SENSE will be performed automatically
 *      for commands that return with a CHECK CONDITION status. 
 *
 * PSEUDO_DMA - enables PSEUDO-DMA hardware, should give a 3-4X performance
 * increase compared to polled I/O.
 *
 * PARITY - enable parity checking.  Not supported.
 *
 * UNSAFE - leave interrupts enabled during pseudo-DMA transfers. 
 *		You probably want this.
 *
 * The card is detected and initialized in one of several ways : 
 * 1.  Autoprobe (default) - since the board is memory mapped, 
 *     a BIOS signature is scanned for to locate the registers.
 *     An interrupt is triggered to autoprobe for the interrupt
 *     line.
 *
 * 2.  With command line overrides - dtc=address,irq may be 
 *     used on the LILO command line to override the defaults.
 * 
*/

/*----------------------------------------------------------------*/
/* the following will set the monitor border color (useful to find
 where something crashed or gets stuck at */
/* 1 = blue
 2 = green
 3 = cyan
 4 = red
 5 = magenta
 6 = yellow
 7 = white
*/
#if 0
#define rtrc(i) {inb(0x3da); outb(0x31, 0x3c0); outb((i), 0x3c0);}
#else
#define rtrc(i) {}
#endif


#include <asm/system.h>
#include <linux/module.h>
#include <linux/signal.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/stat.h>
#include <linux/string.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include "scsi.h"
#include <scsi/scsi_host.h>
#include "dtc.h"
#define AUTOPROBE_IRQ
#include "NCR5380.h"


#define DTC_PUBLIC_RELEASE 2

/*
 * The DTC3180 & 3280 boards are memory mapped.
 * 
 */

/*
 */
/* Offset from DTC_5380_OFFSET */
#define DTC_CONTROL_REG		0x100	/* rw */
#define D_CR_ACCESS		0x80	/* ro set=can access 3280 registers */
#define CSR_DIR_READ		0x40	/* rw direction, 1 = read 0 = write */

#define CSR_RESET              0x80	/* wo  Resets 53c400 */
#define CSR_5380_REG           0x80	/* ro  5380 registers can be accessed */
#define CSR_TRANS_DIR          0x40	/* rw  Data transfer direction */
#define CSR_SCSI_BUFF_INTR     0x20	/* rw  Enable int on transfer ready */
#define CSR_5380_INTR          0x10	/* rw  Enable 5380 interrupts */
#define CSR_SHARED_INTR        0x08	/* rw  Interrupt sharing */
#define CSR_HOST_BUF_NOT_RDY   0x04	/* ro  Host buffer not ready */
#define CSR_SCSI_BUF_RDY       0x02	/* ro  SCSI buffer ready */
#define CSR_GATED_5380_IRQ     0x01	/* ro  Last block xferred */
#define CSR_INT_BASE (CSR_SCSI_BUFF_INTR | CSR_5380_INTR)


#define DTC_BLK_CNT		0x101	/* rw 
					 * # of 128-byte blocks to transfer */


#define D_CR_ACCESS             0x80	/* ro set=can access 3280 registers */

#define DTC_SWITCH_REG		0x3982	/* ro - DIP switches */
#define DTC_RESUME_XFER		0x3982	/* wo - resume data xfer 
					 * after disconnect/reconnect*/

#define DTC_5380_OFFSET		0x3880	/* 8 registers here, see NCR5380.h */

/*!!!! for dtc, it's a 128 byte buffer at 3900 !!! */
#define DTC_DATA_BUF		0x3900	/* rw 128 bytes long */

static struct override {
	unsigned int address;
	int irq;
} overrides
#ifdef OVERRIDE
[] __initdata = OVERRIDE;
#else
[4] __initdata = { {
0, IRQ_AUTO}, {
0, IRQ_AUTO}, {
0, IRQ_AUTO}, {
0, IRQ_AUTO}};
#endif

#define NO_OVERRIDES ARRAY_SIZE(overrides)

static struct base {
	unsigned long address;
	int noauto;
} bases[] __initdata = {
	{ 0xcc000, 0 },
	{ 0xc8000, 0 },
	{ 0xdc000, 0 },
	{ 0xd8000, 0 }
};

#define NO_BASES ARRAY_SIZE(bases)

static const struct signature {
	const char *string;
	int offset;
} signatures[] = {
	{"DATA TECHNOLOGY CORPORATION BIOS", 0x25},
};

#define NO_SIGNATURES ARRAY_SIZE(signatures)

#ifndef MODULE
/*
 * Function : dtc_setup(char *str, int *ints)
 *
 * Purpose : LILO command line initialization of the overrides array,
 *
 * Inputs : str - unused, ints - array of integer parameters with ints[0]
 *	equal to the number of ints.
 *
*/

static void __init dtc_setup(char *str, int *ints)
{
	static int commandline_current = 0;
	int i;
	if (ints[0] != 2)
		printk("dtc_setup: usage dtc=address,irq\n");
	else if (commandline_current < NO_OVERRIDES) {
		overrides[commandline_current].address = ints[1];
		overrides[commandline_current].irq = ints[2];
		for (i = 0; i < NO_BASES; ++i)
			if (bases[i].address == ints[1]) {
				bases[i].noauto = 1;
				break;
			}
		++commandline_current;
	}
}
#endif

/* 
 * Function : int dtc_detect(struct scsi_host_template * tpnt)
 *
 * Purpose : detects and initializes DTC 3180/3280 controllers
 *	that were autoprobed, overridden on the LILO command line, 
 *	or specified at compile time.
 *
 * Inputs : tpnt - template for this SCSI adapter.
 * 
 * Returns : 1 if a host adapter was found, 0 if not.
 *
*/

static int __init dtc_detect(struct scsi_host_template * tpnt)
{
	static int current_override = 0, current_base = 0;
	struct Scsi_Host *instance;
	unsigned int addr;
	void __iomem *base;
	int sig, count;

	tpnt->proc_name = "dtc3x80";
	tpnt->proc_info = &dtc_proc_info;

	for (count = 0; current_override < NO_OVERRIDES; ++current_override) {
		addr = 0;
		base = NULL;

		if (overrides[current_override].address) {
			addr = overrides[current_override].address;
			base = ioremap(addr, 0x2000);
			if (!base)
				addr = 0;
		} else
			for (; !addr && (current_base < NO_BASES); ++current_base) {
#if (DTCDEBUG & DTCDEBUG_INIT)
				printk("scsi-dtc : probing address %08x\n", bases[current_base].address);
#endif
				if (bases[current_base].noauto)
					continue;
				base = ioremap(bases[current_base].address, 0x2000);
				if (!base)
					continue;
				for (sig = 0; sig < NO_SIGNATURES; ++sig) {
					if (check_signature(base + signatures[sig].offset, signatures[sig].string, strlen(signatures[sig].string))) {
						addr = bases[current_base].address;
#if (DTCDEBUG & DTCDEBUG_INIT)
						printk("scsi-dtc : detected board.\n");
#endif
						goto found;
					}
				}
				iounmap(base);
			}

#if defined(DTCDEBUG) && (DTCDEBUG & DTCDEBUG_INIT)
		printk("scsi-dtc : base = %08x\n", addr);
#endif

		if (!addr)
			break;

found:
		instance = scsi_register(tpnt, sizeof(struct NCR5380_hostdata));
		if (instance == NULL)
			break;

		instance->base = addr;
		((struct NCR5380_hostdata *)(instance)->hostdata)->base = base;

		NCR5380_init(instance, 0);

		NCR5380_write(DTC_CONTROL_REG, CSR_5380_INTR);	/* Enable int's */
		if (overrides[current_override].irq != IRQ_AUTO)
			instance->irq = overrides[current_override].irq;
		else
			instance->irq = NCR5380_probe_irq(instance, DTC_IRQS);

#ifndef DONT_USE_INTR
		/* With interrupts enabled, it will sometimes hang when doing heavy
		 * reads. So better not enable them until I finger it out. */
		if (instance->irq != SCSI_IRQ_NONE)
			if (request_irq(instance->irq, dtc_intr, IRQF_DISABLED, "dtc", instance)) {
				printk(KERN_ERR "scsi%d : IRQ%d not free, interrupts disabled\n", instance->host_no, instance->irq);
				instance->irq = SCSI_IRQ_NONE;
			}

		if (instance->irq == SCSI_IRQ_NONE) {
			printk(KERN_WARNING "scsi%d : interrupts not enabled. for better interactive performance,\n", instance->host_no);
			printk(KERN_WARNING "scsi%d : please jumper the board for a free IRQ.\n", instance->host_no);
		}
#else
		if (instance->irq != SCSI_IRQ_NONE)
			printk(KERN_WARNING "scsi%d : interrupts not used. Might as well not jumper it.\n", instance->host_no);
		instance->irq = SCSI_IRQ_NONE;
#endif
#if defined(DTCDEBUG) && (DTCDEBUG & DTCDEBUG_INIT)
		printk("scsi%d : irq = %d\n", instance->host_no, instance->irq);
#endif

		printk(KERN_INFO "scsi%d : at 0x%05X", instance->host_no, (int) instance->base);
		if (instance->irq == SCSI_IRQ_NONE)
			printk(" interrupts disabled");
		else
			printk(" irq %d", instance->irq);
		printk(" options CAN_QUEUE=%d  CMD_PER_LUN=%d release=%d", CAN_QUEUE, CMD_PER_LUN, DTC_PUBLIC_RELEASE);
		NCR5380_print_options(instance);
		printk("\n");

		++current_override;
		++count;
	}
	return count;
}

/*
 * Function : int dtc_biosparam(Disk * disk, struct block_device *dev, int *ip)
 *
 * Purpose : Generates a BIOS / DOS compatible H-C-S mapping for 
 *	the specified device / size.
 * 
 * Inputs : size = size of device in sectors (512 bytes), dev = block device
 *	major / minor, ip[] = {heads, sectors, cylinders}  
 *
 * Returns : always 0 (success), initializes ip
 *	
*/

/* 
 * XXX Most SCSI boards use this mapping, I could be incorrect.  Some one
 * using hard disks on a trantor should verify that this mapping corresponds
 * to that used by the BIOS / ASPI driver by running the linux fdisk program
 * and matching the H_C_S coordinates to what DOS uses.
*/

static int dtc_biosparam(struct scsi_device *sdev, struct block_device *dev,
			 sector_t capacity, int *ip)
{
	int size = capacity;

	ip[0] = 64;
	ip[1] = 32;
	ip[2] = size >> 11;
	return 0;
}


/****************************************************************
 * Function : int NCR5380_pread (struct Scsi_Host *instance, 
 *	unsigned char *dst, int len)
 *
 * Purpose : Fast 5380 pseudo-dma read function, reads len bytes to 
 *	dst
 * 
 * Inputs : dst = destination, len = length in bytes
 *
 * Returns : 0 on success, non zero on a failure such as a watchdog 
 * 	timeout.
*/

static int dtc_maxi = 0;
static int dtc_wmaxi = 0;

static inline int NCR5380_pread(struct Scsi_Host *instance, unsigned char *dst, int len)
{
	unsigned char *d = dst;
	int i;			/* For counting time spent in the poll-loop */
	NCR5380_local_declare();
	NCR5380_setup(instance);

	i = 0;
	NCR5380_read(RESET_PARITY_INTERRUPT_REG);
	NCR5380_write(MODE_REG, MR_ENABLE_EOP_INTR | MR_DMA_MODE);
	if (instance->irq == SCSI_IRQ_NONE)
		NCR5380_write(DTC_CONTROL_REG, CSR_DIR_READ);
	else
		NCR5380_write(DTC_CONTROL_REG, CSR_DIR_READ | CSR_INT_BASE);
	NCR5380_write(DTC_BLK_CNT, len >> 7);	/* Block count */
	rtrc(1);
	while (len > 0) {
		rtrc(2);
		while (NCR5380_read(DTC_CONTROL_REG) & CSR_HOST_BUF_NOT_RDY)
			++i;
		rtrc(3);
		memcpy_fromio(d, base + DTC_DATA_BUF, 128);
		d += 128;
		len -= 128;
		rtrc(7);
		/*** with int's on, it sometimes hangs after here.
		 * Looks like something makes HBNR go away. */
	}
	rtrc(4);
	while (!(NCR5380_read(DTC_CONTROL_REG) & D_CR_ACCESS))
		++i;
	NCR5380_write(MODE_REG, 0);	/* Clear the operating mode */
	rtrc(0);
	NCR5380_read(RESET_PARITY_INTERRUPT_REG);
	if (i > dtc_maxi)
		dtc_maxi = i;
	return (0);
}

/****************************************************************
 * Function : int NCR5380_pwrite (struct Scsi_Host *instance, 
 *	unsigned char *src, int len)
 *
 * Purpose : Fast 5380 pseudo-dma write function, transfers len bytes from
 *	src
 * 
 * Inputs : src = source, len = length in bytes
 *
 * Returns : 0 on success, non zero on a failure such as a watchdog 
 * 	timeout.
*/

static inline int NCR5380_pwrite(struct Scsi_Host *instance, unsigned char *src, int len)
{
	int i;
	NCR5380_local_declare();
	NCR5380_setup(instance);

	NCR5380_read(RESET_PARITY_INTERRUPT_REG);
	NCR5380_write(MODE_REG, MR_ENABLE_EOP_INTR | MR_DMA_MODE);
	/* set direction (write) */
	if (instance->irq == SCSI_IRQ_NONE)
		NCR5380_write(DTC_CONTROL_REG, 0);
	else
		NCR5380_write(DTC_CONTROL_REG, CSR_5380_INTR);
	NCR5380_write(DTC_BLK_CNT, len >> 7);	/* Block count */
	for (i = 0; len > 0; ++i) {
		rtrc(5);
		/* Poll until the host buffer can accept data. */
		while (NCR5380_read(DTC_CONTROL_REG) & CSR_HOST_BUF_NOT_RDY)
			++i;
		rtrc(3);
		memcpy_toio(base + DTC_DATA_BUF, src, 128);
		src += 128;
		len -= 128;
	}
	rtrc(4);
	while (!(NCR5380_read(DTC_CONTROL_REG) & D_CR_ACCESS))
		++i;
	rtrc(6);
	/* Wait until the last byte has been sent to the disk */
	while (!(NCR5380_read(TARGET_COMMAND_REG) & TCR_LAST_BYTE_SENT))
		++i;
	rtrc(7);
	/* Check for parity error here. fixme. */
	NCR5380_write(MODE_REG, 0);	/* Clear the operating mode */
	rtrc(0);
	if (i > dtc_wmaxi)
		dtc_wmaxi = i;
	return (0);
}

MODULE_LICENSE("GPL");

#include "NCR5380.c"

static int dtc_release(struct Scsi_Host *shost)
{
	NCR5380_local_declare();
	NCR5380_setup(shost);
	if (shost->irq)
		free_irq(shost->irq, NULL);
	NCR5380_exit(shost);
	if (shost->io_port && shost->n_io_port)
		release_region(shost->io_port, shost->n_io_port);
	scsi_unregister(shost);
	iounmap(base);
	return 0;
}

static struct scsi_host_template driver_template = {
	.name				= "DTC 3180/3280 ",
	.detect				= dtc_detect,
	.release			= dtc_release,
	.queuecommand			= dtc_queue_command,
	.eh_abort_handler		= dtc_abort,
	.eh_bus_reset_handler		= dtc_bus_reset,
	.bios_param     		= dtc_biosparam,
	.can_queue      		= CAN_QUEUE,
	.this_id        		= 7,
	.sg_tablesize   		= SG_ALL,
	.cmd_per_lun    		= CMD_PER_LUN,
	.use_clustering 		= DISABLE_CLUSTERING,
};
#include "scsi_module.c"
Commit	Line	Data
1da177e4 LT	1
	2	#define AUTOSENSE
	3	#define PSEUDO_DMA
	4	#define DONT_USE_INTR
	5	#define UNSAFE /* Leave interrupts enabled during pseudo-dma I/O */
	6	#define xNDEBUG (NDEBUG_INTR+NDEBUG_RESELECTION+\
	7	NDEBUG_SELECTION+NDEBUG_ARBITRATION)
	8	#define DMA_WORKS_RIGHT
	9
	10
	11	/*
	12	* DTC 3180/3280 driver, by
	13	* Ray Van Tassle [email protected]
	14	*
	15	* taken from ...
	16	* Trantor T128/T128F/T228 driver by...
	17	*
	18	* Drew Eckhardt
	19	* Visionary Computing
	20	* (Unix and Linux consulting and custom programming)
	21	* [email protected]
	22	* +1 (303) 440-4894
	23	*
	24	* DISTRIBUTION RELEASE 1.
	25	*
	26	* For more information, please consult
	27	*
	28	* NCR 5380 Family
	29	* SCSI Protocol Controller
	30	* Databook
	31	*/
	32
	33	/*
	34	* Options :
	35	* AUTOSENSE - if defined, REQUEST SENSE will be performed automatically
	36	* for commands that return with a CHECK CONDITION status.
	37	*
	38	* PSEUDO_DMA - enables PSEUDO-DMA hardware, should give a 3-4X performance
	39	* increase compared to polled I/O.
	40	*
	41	* PARITY - enable parity checking. Not supported.
	42	*
	43	* UNSAFE - leave interrupts enabled during pseudo-DMA transfers.
	44	* You probably want this.
	45	*
	46	* The card is detected and initialized in one of several ways :
	47	* 1. Autoprobe (default) - since the board is memory mapped,
	48	* a BIOS signature is scanned for to locate the registers.
	49	* An interrupt is triggered to autoprobe for the interrupt
	50	* line.
	51	*
	52	* 2. With command line overrides - dtc=address,irq may be
	53	* used on the LILO command line to override the defaults.
	54	*
	55	*/
	56
	57	/----------------------------------------------------------------/
	58	/* the following will set the monitor border color (useful to find
	59	where something crashed or gets stuck at */
	60	/* 1 = blue
	61	2 = green
	62	3 = cyan
	63	4 = red
	64	5 = magenta
65	6 = yellow
66	7 = white
67	*/
68	#if 0
69	#define rtrc(i) {inb(0x3da); outb(0x31, 0x3c0); outb((i), 0x3c0);}
70	#else
71	#define rtrc(i) {}
72	#endif
73
74
75	#include <asm/system.h>
76	#include <linux/module.h>
77	#include <linux/signal.h>
1da177e4 LT	78	#include <linux/blkdev.h>
	79	#include <linux/delay.h>
	80	#include <linux/stat.h>
	81	#include <linux/string.h>
	82	#include <linux/init.h>
	83	#include <linux/interrupt.h>
53d5ed62	84	#include <linux/io.h>
1da177e4 LT	85	#include "scsi.h"
	86	#include <scsi/scsi_host.h>
	87	#include "dtc.h"
	88	#define AUTOPROBE_IRQ
	89	#include "NCR5380.h"
	90
	91
	92	#define DTC_PUBLIC_RELEASE 2
	93
1da177e4 LT	94	/*
	95	* The DTC3180 & 3280 boards are memory mapped.
	96	*
	97	*/
	98
	99	/*
	100	*/
	101	/* Offset from DTC_5380_OFFSET */
	102	#define DTC_CONTROL_REG 0x100 /* rw */
	103	#define D_CR_ACCESS 0x80 /* ro set=can access 3280 registers */
	104	#define CSR_DIR_READ 0x40 /* rw direction, 1 = read 0 = write */
	105
	106	#define CSR_RESET 0x80 /* wo Resets 53c400 */
	107	#define CSR_5380_REG 0x80 /* ro 5380 registers can be accessed */
	108	#define CSR_TRANS_DIR 0x40 /* rw Data transfer direction */
	109	#define CSR_SCSI_BUFF_INTR 0x20 /* rw Enable int on transfer ready */
	110	#define CSR_5380_INTR 0x10 /* rw Enable 5380 interrupts */
	111	#define CSR_SHARED_INTR 0x08 /* rw Interrupt sharing */
	112	#define CSR_HOST_BUF_NOT_RDY 0x04 /* ro Host buffer not ready */
	113	#define CSR_SCSI_BUF_RDY 0x02 /* ro SCSI buffer ready */
	114	#define CSR_GATED_5380_IRQ 0x01 /* ro Last block xferred */
	115	#define CSR_INT_BASE (CSR_SCSI_BUFF_INTR \| CSR_5380_INTR)
	116
	117
	118	#define DTC_BLK_CNT 0x101 /* rw
	119	* # of 128-byte blocks to transfer */
	120
	121
	122	#define D_CR_ACCESS 0x80 /* ro set=can access 3280 registers */
	123
	124	#define DTC_SWITCH_REG 0x3982 /* ro - DIP switches */
	125	#define DTC_RESUME_XFER 0x3982 /* wo - resume data xfer
	126	* after disconnect/reconnect*/
	127
	128	#define DTC_5380_OFFSET 0x3880 /* 8 registers here, see NCR5380.h */
	129
	130	/!!!! for dtc, it's a 128 byte buffer at 3900 !!! /
	131	#define DTC_DATA_BUF 0x3900 /* rw 128 bytes long */
	132
	133	static struct override {
	134	unsigned int address;
	135	int irq;
	136	} overrides
	137	#ifdef OVERRIDE
	138	[] __initdata = OVERRIDE;
	139	#else
	140	[4] __initdata = { {
	141	0, IRQ_AUTO}, {
	142	0, IRQ_AUTO}, {
	143	0, IRQ_AUTO}, {
	144	0, IRQ_AUTO}};
	145	#endif
	146
6391a113	147	#define NO_OVERRIDES ARRAY_SIZE(overrides)
1da177e4 LT	148
	149	static struct base {
	150	unsigned long address;
	151	int noauto;
6391a113 TK	152	} bases[] __initdata = {
	153	{ 0xcc000, 0 },
	154	{ 0xc8000, 0 },
	155	{ 0xdc000, 0 },
1da177e4 LT	156	{ 0xd8000, 0 }
	157	};
	158
6391a113	159	#define NO_BASES ARRAY_SIZE(bases)
1da177e4 LT	160
	161	static const struct signature {
	162	const char *string;
	163	int offset;
6391a113	164	} signatures[] = {
1da177e4 LT	165	{"DATA TECHNOLOGY CORPORATION BIOS", 0x25},
	166	};
	167
6391a113	168	#define NO_SIGNATURES ARRAY_SIZE(signatures)
1da177e4 LT	169
	170	#ifndef MODULE
	171	/*
	172	* Function : dtc_setup(char str, int ints)
	173	*
	174	* Purpose : LILO command line initialization of the overrides array,
6391a113	175	*
1da177e4 LT	176	* Inputs : str - unused, ints - array of integer parameters with ints[0]
	177	* equal to the number of ints.
	178	*
	179	*/
	180
	181	static void __init dtc_setup(char str, int ints)
	182	{
	183	static int commandline_current = 0;
	184	int i;
	185	if (ints[0] != 2)
	186	printk("dtc_setup: usage dtc=address,irq\n");
	187	else if (commandline_current < NO_OVERRIDES) {
	188	overrides[commandline_current].address = ints[1];
	189	overrides[commandline_current].irq = ints[2];
	190	for (i = 0; i < NO_BASES; ++i)
	191	if (bases[i].address == ints[1]) {
	192	bases[i].noauto = 1;
	193	break;
	194	}
	195	++commandline_current;
	196	}
	197	}
	198	#endif
	199
	200	/*
d0be4a7d	201	* Function : int dtc_detect(struct scsi_host_template * tpnt)
1da177e4 LT	202	*
	203	* Purpose : detects and initializes DTC 3180/3280 controllers
	204	* that were autoprobed, overridden on the LILO command line,
	205	* or specified at compile time.
	206	*
	207	* Inputs : tpnt - template for this SCSI adapter.
	208	*
	209	* Returns : 1 if a host adapter was found, 0 if not.
	210	*
	211	*/
	212
d0be4a7d	213	static int __init dtc_detect(struct scsi_host_template * tpnt)
1da177e4 LT	214	{
	215	static int current_override = 0, current_base = 0;
	216	struct Scsi_Host *instance;
	217	unsigned int addr;
	218	void __iomem *base;
	219	int sig, count;
	220
	221	tpnt->proc_name = "dtc3x80";
	222	tpnt->proc_info = &dtc_proc_info;
	223
	224	for (count = 0; current_override < NO_OVERRIDES; ++current_override) {
	225	addr = 0;
	226	base = NULL;
	227
	228	if (overrides[current_override].address) {
	229	addr = overrides[current_override].address;
	230	base = ioremap(addr, 0x2000);
	231	if (!base)
	232	addr = 0;
	233	} else
	234	for (; !addr && (current_base < NO_BASES); ++current_base) {
	235	#if (DTCDEBUG & DTCDEBUG_INIT)
	236	printk("scsi-dtc : probing address %08x\n", bases[current_base].address);
	237	#endif
	238	if (bases[current_base].noauto)
	239	continue;
	240	base = ioremap(bases[current_base].address, 0x2000);
	241	if (!base)
	242	continue;
	243	for (sig = 0; sig < NO_SIGNATURES; ++sig) {
	244	if (check_signature(base + signatures[sig].offset, signatures[sig].string, strlen(signatures[sig].string))) {
	245	addr = bases[current_base].address;
	246	#if (DTCDEBUG & DTCDEBUG_INIT)
	247	printk("scsi-dtc : detected board.\n");
	248	#endif
	249	goto found;
	250	}
	251	}
	252	iounmap(base);
	253	}
	254
	255	#if defined(DTCDEBUG) && (DTCDEBUG & DTCDEBUG_INIT)
	256	printk("scsi-dtc : base = %08x\n", addr);
	257	#endif
	258
	259	if (!addr)
	260	break;
	261
	262	found:
	263	instance = scsi_register(tpnt, sizeof(struct NCR5380_hostdata));
	264	if (instance == NULL)
	265	break;
	266
	267	instance->base = addr;
	268	((struct NCR5380_hostdata *)(instance)->hostdata)->base = base;
	269
	270	NCR5380_init(instance, 0);
	271
	272	NCR5380_write(DTC_CONTROL_REG, CSR_5380_INTR); /* Enable int's */
	273	if (overrides[current_override].irq != IRQ_AUTO)
	274	instance->irq = overrides[current_override].irq;
	275	else
	276	instance->irq = NCR5380_probe_irq(instance, DTC_IRQS);
	277
278	#ifndef DONT_USE_INTR
279	/* With interrupts enabled, it will sometimes hang when doing heavy
280	* reads. So better not enable them until I finger it out. */
281	if (instance->irq != SCSI_IRQ_NONE)
1d6f359a	282	if (request_irq(instance->irq, dtc_intr, IRQF_DISABLED, "dtc", instance)) {
1da177e4 LT	283	printk(KERN_ERR "scsi%d : IRQ%d not free, interrupts disabled\n", instance->host_no, instance->irq);
	284	instance->irq = SCSI_IRQ_NONE;
	285	}
	286
	287	if (instance->irq == SCSI_IRQ_NONE) {
	288	printk(KERN_WARNING "scsi%d : interrupts not enabled. for better interactive performance,\n", instance->host_no);
	289	printk(KERN_WARNING "scsi%d : please jumper the board for a free IRQ.\n", instance->host_no);
	290	}
	291	#else
	292	if (instance->irq != SCSI_IRQ_NONE)
	293	printk(KERN_WARNING "scsi%d : interrupts not used. Might as well not jumper it.\n", instance->host_no);
	294	instance->irq = SCSI_IRQ_NONE;
	295	#endif
	296	#if defined(DTCDEBUG) && (DTCDEBUG & DTCDEBUG_INIT)
	297	printk("scsi%d : irq = %d\n", instance->host_no, instance->irq);
	298	#endif
	299
	300	printk(KERN_INFO "scsi%d : at 0x%05X", instance->host_no, (int) instance->base);
	301	if (instance->irq == SCSI_IRQ_NONE)
	302	printk(" interrupts disabled");
	303	else
	304	printk(" irq %d", instance->irq);
	305	printk(" options CAN_QUEUE=%d CMD_PER_LUN=%d release=%d", CAN_QUEUE, CMD_PER_LUN, DTC_PUBLIC_RELEASE);
	306	NCR5380_print_options(instance);
	307	printk("\n");
	308
	309	++current_override;
	310	++count;
	311	}
	312	return count;
	313	}
	314
	315	/*
	316	* Function : int dtc_biosparam(Disk * disk, struct block_device dev, int ip)
	317	*
	318	* Purpose : Generates a BIOS / DOS compatible H-C-S mapping for
	319	* the specified device / size.
	320	*
	321	* Inputs : size = size of device in sectors (512 bytes), dev = block device
	322	* major / minor, ip[] = {heads, sectors, cylinders}
	323	*
	324	* Returns : always 0 (success), initializes ip
	325	*
	326	*/
	327
	328	/*
	329	* XXX Most SCSI boards use this mapping, I could be incorrect. Some one
	330	* using hard disks on a trantor should verify that this mapping corresponds
	331	* to that used by the BIOS / ASPI driver by running the linux fdisk program
	332	* and matching the H_C_S coordinates to what DOS uses.
	333	*/
	334
	335	static int dtc_biosparam(struct scsi_device sdev, struct block_device dev,
	336	sector_t capacity, int *ip)
	337	{
	338	int size = capacity;
	339
	340	ip[0] = 64;
	341	ip[1] = 32;
	342	ip[2] = size >> 11;
	343	return 0;
	344	}
	345
	346
347	/****************************************************************
348	* Function : int NCR5380_pread (struct Scsi_Host *instance,
349	* unsigned char *dst, int len)
350	*
351	* Purpose : Fast 5380 pseudo-dma read function, reads len bytes to
352	* dst
353	*
354	* Inputs : dst = destination, len = length in bytes
355	*
356	* Returns : 0 on success, non zero on a failure such as a watchdog
357	* timeout.
358	*/
359
360	static int dtc_maxi = 0;
361	static int dtc_wmaxi = 0;
362
363	static inline int NCR5380_pread(struct Scsi_Host instance, unsigned char dst, int len)
364	{
365	unsigned char *d = dst;
366	int i; /* For counting time spent in the poll-loop */
367	NCR5380_local_declare();
368	NCR5380_setup(instance);
369
370	i = 0;
371	NCR5380_read(RESET_PARITY_INTERRUPT_REG);
372	NCR5380_write(MODE_REG, MR_ENABLE_EOP_INTR \| MR_DMA_MODE);
373	if (instance->irq == SCSI_IRQ_NONE)
374	NCR5380_write(DTC_CONTROL_REG, CSR_DIR_READ);
375	else
376	NCR5380_write(DTC_CONTROL_REG, CSR_DIR_READ \| CSR_INT_BASE);
377	NCR5380_write(DTC_BLK_CNT, len >> 7); /* Block count */
378	rtrc(1);
379	while (len > 0) {
380	rtrc(2);
381	while (NCR5380_read(DTC_CONTROL_REG) & CSR_HOST_BUF_NOT_RDY)
382	++i;
383	rtrc(3);
384	memcpy_fromio(d, base + DTC_DATA_BUF, 128);
385	d += 128;
386	len -= 128;
387	rtrc(7);
388	/*** with int's on, it sometimes hangs after here.
389	* Looks like something makes HBNR go away. */
390	}
391	rtrc(4);
392	while (!(NCR5380_read(DTC_CONTROL_REG) & D_CR_ACCESS))
393	++i;
394	NCR5380_write(MODE_REG, 0); /* Clear the operating mode */
395	rtrc(0);
396	NCR5380_read(RESET_PARITY_INTERRUPT_REG);
397	if (i > dtc_maxi)
398	dtc_maxi = i;
399	return (0);
400	}
401
402	/****************************************************************
403	* Function : int NCR5380_pwrite (struct Scsi_Host *instance,
404	* unsigned char *src, int len)
405	*
406	* Purpose : Fast 5380 pseudo-dma write function, transfers len bytes from
407	* src
408	*
409	* Inputs : src = source, len = length in bytes
410	*
411	* Returns : 0 on success, non zero on a failure such as a watchdog
412	* timeout.
413	*/
414
415	static inline int NCR5380_pwrite(struct Scsi_Host instance, unsigned char src, int len)
416	{
417	int i;
418	NCR5380_local_declare();
419	NCR5380_setup(instance);
420
421	NCR5380_read(RESET_PARITY_INTERRUPT_REG);
422	NCR5380_write(MODE_REG, MR_ENABLE_EOP_INTR \| MR_DMA_MODE);
423	/* set direction (write) */
424	if (instance->irq == SCSI_IRQ_NONE)
425	NCR5380_write(DTC_CONTROL_REG, 0);
426	else
427	NCR5380_write(DTC_CONTROL_REG, CSR_5380_INTR);
428	NCR5380_write(DTC_BLK_CNT, len >> 7); /* Block count */
429	for (i = 0; len > 0; ++i) {
430	rtrc(5);
431	/* Poll until the host buffer can accept data. */
432	while (NCR5380_read(DTC_CONTROL_REG) & CSR_HOST_BUF_NOT_RDY)
433	++i;
434	rtrc(3);
435	memcpy_toio(base + DTC_DATA_BUF, src, 128);
436	src += 128;
437	len -= 128;
438	}
439	rtrc(4);
440	while (!(NCR5380_read(DTC_CONTROL_REG) & D_CR_ACCESS))
441	++i;
442	rtrc(6);
443	/* Wait until the last byte has been sent to the disk */
444	while (!(NCR5380_read(TARGET_COMMAND_REG) & TCR_LAST_BYTE_SENT))
445	++i;
446	rtrc(7);
447	/* Check for parity error here. fixme. */
448	NCR5380_write(MODE_REG, 0); /* Clear the operating mode */
449	rtrc(0);
450	if (i > dtc_wmaxi)
451	dtc_wmaxi = i;
452	return (0);
453	}
454
455	MODULE_LICENSE("GPL");
456
457	#include "NCR5380.c"
458
459	static int dtc_release(struct Scsi_Host *shost)
460	{
461	NCR5380_local_declare();
462	NCR5380_setup(shost);
463	if (shost->irq)
464	free_irq(shost->irq, NULL);
465	NCR5380_exit(shost);
466	if (shost->io_port && shost->n_io_port)
467	release_region(shost->io_port, shost->n_io_port);
468	scsi_unregister(shost);
469	iounmap(base);
470	return 0;
471	}
472
d0be4a7d	473	static struct scsi_host_template driver_template = {
1da177e4 LT	474	.name = "DTC 3180/3280 ",
	475	.detect = dtc_detect,
	476	.release = dtc_release,
	477	.queuecommand = dtc_queue_command,
	478	.eh_abort_handler = dtc_abort,
	479	.eh_bus_reset_handler = dtc_bus_reset,
1da177e4 LT	480	.bios_param = dtc_biosparam,
	481	.can_queue = CAN_QUEUE,
	482	.this_id = 7,
	483	.sg_tablesize = SG_ALL,
	484	.cmd_per_lun = CMD_PER_LUN,
	485	.use_clustering = DISABLE_CLUSTERING,
	486	};
	487	#include "scsi_module.c"