]>
Commit | Line | Data |
---|---|---|
800e69fb IS |
1 | /* |
2 | * Janz MODULbus VMOD-TTL GPIO Driver | |
3 | * | |
4 | * Copyright (c) 2010 Ira W. Snyder <[email protected]> | |
5 | * | |
6 | * This program is free software; you can redistribute it and/or modify it | |
7 | * under the terms of the GNU General Public License as published by the | |
8 | * Free Software Foundation; either version 2 of the License, or (at your | |
9 | * option) any later version. | |
10 | */ | |
11 | ||
12 | #include <linux/kernel.h> | |
13 | #include <linux/module.h> | |
14 | #include <linux/init.h> | |
15 | #include <linux/interrupt.h> | |
16 | #include <linux/delay.h> | |
17 | #include <linux/platform_device.h> | |
18 | #include <linux/io.h> | |
19 | #include <linux/gpio.h> | |
20 | #include <linux/slab.h> | |
21 | ||
22 | #include <linux/mfd/janz.h> | |
23 | ||
24 | #define DRV_NAME "janz-ttl" | |
25 | ||
26 | #define PORTA_DIRECTION 0x23 | |
27 | #define PORTB_DIRECTION 0x2B | |
28 | #define PORTC_DIRECTION 0x06 | |
29 | #define PORTA_IOCTL 0x24 | |
30 | #define PORTB_IOCTL 0x2C | |
31 | #define PORTC_IOCTL 0x07 | |
32 | ||
33 | #define MASTER_INT_CTL 0x00 | |
34 | #define MASTER_CONF_CTL 0x01 | |
35 | ||
36 | #define CONF_PAE (1 << 2) | |
37 | #define CONF_PBE (1 << 7) | |
38 | #define CONF_PCE (1 << 4) | |
39 | ||
40 | struct ttl_control_regs { | |
41 | __be16 portc; | |
42 | __be16 portb; | |
43 | __be16 porta; | |
44 | __be16 control; | |
45 | }; | |
46 | ||
47 | struct ttl_module { | |
48 | struct gpio_chip gpio; | |
49 | ||
50 | /* base address of registers */ | |
51 | struct ttl_control_regs __iomem *regs; | |
52 | ||
53 | u8 portc_shadow; | |
54 | u8 portb_shadow; | |
55 | u8 porta_shadow; | |
56 | ||
57 | spinlock_t lock; | |
58 | }; | |
59 | ||
60 | static int ttl_get_value(struct gpio_chip *gpio, unsigned offset) | |
61 | { | |
58383c78 | 62 | struct ttl_module *mod = dev_get_drvdata(gpio->parent); |
800e69fb IS |
63 | u8 *shadow; |
64 | int ret; | |
65 | ||
66 | if (offset < 8) { | |
67 | shadow = &mod->porta_shadow; | |
68 | } else if (offset < 16) { | |
69 | shadow = &mod->portb_shadow; | |
70 | offset -= 8; | |
71 | } else { | |
72 | shadow = &mod->portc_shadow; | |
73 | offset -= 16; | |
74 | } | |
75 | ||
76 | spin_lock(&mod->lock); | |
77 | ret = *shadow & (1 << offset); | |
78 | spin_unlock(&mod->lock); | |
828240c2 | 79 | return !!ret; |
800e69fb IS |
80 | } |
81 | ||
82 | static void ttl_set_value(struct gpio_chip *gpio, unsigned offset, int value) | |
83 | { | |
58383c78 | 84 | struct ttl_module *mod = dev_get_drvdata(gpio->parent); |
800e69fb IS |
85 | void __iomem *port; |
86 | u8 *shadow; | |
87 | ||
88 | if (offset < 8) { | |
89 | port = &mod->regs->porta; | |
90 | shadow = &mod->porta_shadow; | |
91 | } else if (offset < 16) { | |
92 | port = &mod->regs->portb; | |
93 | shadow = &mod->portb_shadow; | |
94 | offset -= 8; | |
95 | } else { | |
96 | port = &mod->regs->portc; | |
97 | shadow = &mod->portc_shadow; | |
98 | offset -= 16; | |
99 | } | |
100 | ||
101 | spin_lock(&mod->lock); | |
102 | if (value) | |
103 | *shadow |= (1 << offset); | |
104 | else | |
105 | *shadow &= ~(1 << offset); | |
106 | ||
107 | iowrite16be(*shadow, port); | |
108 | spin_unlock(&mod->lock); | |
109 | } | |
110 | ||
3836309d | 111 | static void ttl_write_reg(struct ttl_module *mod, u8 reg, u16 val) |
800e69fb IS |
112 | { |
113 | iowrite16be(reg, &mod->regs->control); | |
114 | iowrite16be(val, &mod->regs->control); | |
115 | } | |
116 | ||
3836309d | 117 | static void ttl_setup_device(struct ttl_module *mod) |
800e69fb IS |
118 | { |
119 | /* reset the device to a known state */ | |
120 | iowrite16be(0x0000, &mod->regs->control); | |
121 | iowrite16be(0x0001, &mod->regs->control); | |
122 | iowrite16be(0x0000, &mod->regs->control); | |
123 | ||
124 | /* put all ports in open-drain mode */ | |
125 | ttl_write_reg(mod, PORTA_IOCTL, 0x00ff); | |
126 | ttl_write_reg(mod, PORTB_IOCTL, 0x00ff); | |
127 | ttl_write_reg(mod, PORTC_IOCTL, 0x000f); | |
128 | ||
129 | /* set all ports as outputs */ | |
130 | ttl_write_reg(mod, PORTA_DIRECTION, 0x0000); | |
131 | ttl_write_reg(mod, PORTB_DIRECTION, 0x0000); | |
132 | ttl_write_reg(mod, PORTC_DIRECTION, 0x0000); | |
133 | ||
134 | /* set all ports to drive zeroes */ | |
135 | iowrite16be(0x0000, &mod->regs->porta); | |
136 | iowrite16be(0x0000, &mod->regs->portb); | |
137 | iowrite16be(0x0000, &mod->regs->portc); | |
138 | ||
139 | /* enable all ports */ | |
140 | ttl_write_reg(mod, MASTER_CONF_CTL, CONF_PAE | CONF_PBE | CONF_PCE); | |
141 | } | |
142 | ||
3836309d | 143 | static int ttl_probe(struct platform_device *pdev) |
800e69fb IS |
144 | { |
145 | struct janz_platform_data *pdata; | |
146 | struct device *dev = &pdev->dev; | |
147 | struct ttl_module *mod; | |
148 | struct gpio_chip *gpio; | |
149 | struct resource *res; | |
150 | int ret; | |
151 | ||
e56aee18 | 152 | pdata = dev_get_platdata(&pdev->dev); |
800e69fb IS |
153 | if (!pdata) { |
154 | dev_err(dev, "no platform data\n"); | |
ae28193e | 155 | return -ENXIO; |
800e69fb IS |
156 | } |
157 | ||
ae28193e | 158 | mod = devm_kzalloc(dev, sizeof(*mod), GFP_KERNEL); |
159 | if (!mod) | |
160 | return -ENOMEM; | |
800e69fb IS |
161 | |
162 | platform_set_drvdata(pdev, mod); | |
163 | spin_lock_init(&mod->lock); | |
164 | ||
165 | /* get access to the MODULbus registers for this module */ | |
166 | res = platform_get_resource(pdev, IORESOURCE_MEM, 0); | |
ae28193e | 167 | mod->regs = devm_ioremap_resource(dev, res); |
168 | if (IS_ERR(mod->regs)) | |
169 | return PTR_ERR(mod->regs); | |
800e69fb IS |
170 | |
171 | ttl_setup_device(mod); | |
172 | ||
173 | /* Initialize the GPIO data structures */ | |
174 | gpio = &mod->gpio; | |
58383c78 | 175 | gpio->parent = &pdev->dev; |
800e69fb IS |
176 | gpio->label = pdev->name; |
177 | gpio->get = ttl_get_value; | |
178 | gpio->set = ttl_set_value; | |
179 | gpio->owner = THIS_MODULE; | |
180 | ||
181 | /* request dynamic allocation */ | |
182 | gpio->base = -1; | |
183 | gpio->ngpio = 20; | |
184 | ||
abeb3f40 | 185 | ret = devm_gpiochip_add_data(dev, gpio, NULL); |
800e69fb IS |
186 | if (ret) { |
187 | dev_err(dev, "unable to add GPIO chip\n"); | |
ae28193e | 188 | return ret; |
800e69fb IS |
189 | } |
190 | ||
800e69fb | 191 | return 0; |
800e69fb IS |
192 | } |
193 | ||
800e69fb IS |
194 | static struct platform_driver ttl_driver = { |
195 | .driver = { | |
196 | .name = DRV_NAME, | |
800e69fb IS |
197 | }, |
198 | .probe = ttl_probe, | |
800e69fb IS |
199 | }; |
200 | ||
6f61415e | 201 | module_platform_driver(ttl_driver); |
800e69fb IS |
202 | |
203 | MODULE_AUTHOR("Ira W. Snyder <[email protected]>"); | |
204 | MODULE_DESCRIPTION("Janz MODULbus VMOD-TTL Driver"); | |
205 | MODULE_LICENSE("GPL"); | |
206 | MODULE_ALIAS("platform:janz-ttl"); |