[linux.git] / drivers / phy / phy-miphy365x.c

/*
 * Copyright (C) 2014 STMicroelectronics – All Rights Reserved
 *
 * STMicroelectronics PHY driver MiPHY365 (for SoC STiH416).
 *
 * Authors: Alexandre Torgue <[email protected]>
 *          Lee Jones <[email protected]>
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2, as
 * published by the Free Software Foundation.
 *
 */

#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_platform.h>
#include <linux/of_address.h>
#include <linux/clk.h>
#include <linux/phy/phy.h>
#include <linux/delay.h>
#include <linux/mfd/syscon.h>
#include <linux/regmap.h>

#include <dt-bindings/phy/phy-miphy365x.h>

#define HFC_TIMEOUT		100

#define SYSCFG_SELECT_SATA_MASK	BIT(1)
#define SYSCFG_SELECT_SATA_POS	1

/* MiPHY365x register definitions */
#define RESET_REG		0x00
#define RST_PLL			BIT(1)
#define RST_PLL_CAL		BIT(2)
#define RST_RX			BIT(4)
#define RST_MACRO		BIT(7)

#define STATUS_REG		0x01
#define IDLL_RDY		BIT(0)
#define PLL_RDY			BIT(1)
#define DES_BIT_LOCK		BIT(2)
#define DES_SYMBOL_LOCK		BIT(3)

#define CTRL_REG		0x02
#define TERM_EN			BIT(0)
#define PCI_EN			BIT(2)
#define DES_BIT_LOCK_EN		BIT(3)
#define TX_POL			BIT(5)

#define INT_CTRL_REG		0x03

#define BOUNDARY1_REG		0x10
#define SPDSEL_SEL		BIT(0)

#define BOUNDARY3_REG		0x12
#define TX_SPDSEL_GEN1_VAL	0
#define TX_SPDSEL_GEN2_VAL	0x01
#define TX_SPDSEL_GEN3_VAL	0x02
#define RX_SPDSEL_GEN1_VAL	0
#define RX_SPDSEL_GEN2_VAL	(0x01 << 3)
#define RX_SPDSEL_GEN3_VAL	(0x02 << 3)

#define PCIE_REG		0x16

#define BUF_SEL_REG		0x20
#define CONF_GEN_SEL_GEN3	0x02
#define CONF_GEN_SEL_GEN2	0x01
#define PD_VDDTFILTER		BIT(4)

#define TXBUF1_REG		0x21
#define SWING_VAL		0x04
#define SWING_VAL_GEN1		0x03
#define PREEMPH_VAL		(0x3 << 5)

#define TXBUF2_REG		0x22
#define TXSLEW_VAL		0x2
#define TXSLEW_VAL_GEN1		0x4

#define RXBUF_OFFSET_CTRL_REG	0x23

#define RXBUF_REG		0x25
#define SDTHRES_VAL		0x01
#define EQ_ON3			(0x03 << 4)
#define EQ_ON1			(0x01 << 4)

#define COMP_CTRL1_REG		0x40
#define START_COMSR		BIT(0)
#define START_COMZC		BIT(1)
#define COMSR_DONE		BIT(2)
#define COMZC_DONE		BIT(3)
#define COMP_AUTO_LOAD		BIT(4)

#define COMP_CTRL2_REG		0x41
#define COMP_2MHZ_RAT_GEN1	0x1e
#define COMP_2MHZ_RAT		0xf

#define COMP_CTRL3_REG		0x42
#define COMSR_COMP_REF		0x33

#define COMP_IDLL_REG		0x47
#define COMZC_IDLL		0x2a

#define PLL_CTRL1_REG		0x50
#define PLL_START_CAL		BIT(0)
#define BUF_EN			BIT(2)
#define SYNCHRO_TX		BIT(3)
#define SSC_EN			BIT(6)
#define CONFIG_PLL		BIT(7)

#define PLL_CTRL2_REG		0x51
#define BYPASS_PLL_CAL		BIT(1)

#define PLL_RAT_REG		0x52

#define PLL_SSC_STEP_MSB_REG	0x56
#define PLL_SSC_STEP_MSB_VAL	0x03

#define PLL_SSC_STEP_LSB_REG	0x57
#define PLL_SSC_STEP_LSB_VAL	0x63

#define PLL_SSC_PER_MSB_REG	0x58
#define PLL_SSC_PER_MSB_VAL	0

#define PLL_SSC_PER_LSB_REG	0x59
#define PLL_SSC_PER_LSB_VAL	0xf1

#define IDLL_TEST_REG		0x72
#define START_CLK_HF		BIT(6)

#define DES_BITLOCK_REG		0x86
#define BIT_LOCK_LEVEL		0x01
#define BIT_LOCK_CNT_512	(0x03 << 5)

struct miphy365x_phy {
	struct phy *phy;
	void __iomem *base;
	bool pcie_tx_pol_inv;
	bool sata_tx_pol_inv;
	u32 sata_gen;
	u64 ctrlreg;
	u8 type;
};

struct miphy365x_dev {
	struct device *dev;
	struct regmap *regmap;
	struct mutex miphy_mutex;
	struct miphy365x_phy **phys;
};

/*
 * These values are represented in Device tree. They are considered to be ABI
 * and although they can be extended any existing values must not change.
 */
enum miphy_sata_gen {
	SATA_GEN1 = 1,
	SATA_GEN2,
	SATA_GEN3
};

static u8 rx_tx_spd[] = {
	0, /* GEN0 doesn't exist. */
	TX_SPDSEL_GEN1_VAL | RX_SPDSEL_GEN1_VAL,
	TX_SPDSEL_GEN2_VAL | RX_SPDSEL_GEN2_VAL,
	TX_SPDSEL_GEN3_VAL | RX_SPDSEL_GEN3_VAL
};

/*
 * This function selects the system configuration,
 * either two SATA, one SATA and one PCIe, or two PCIe lanes.
 */
static int miphy365x_set_path(struct miphy365x_phy *miphy_phy,
			      struct miphy365x_dev *miphy_dev)
{
	bool sata = (miphy_phy->type == MIPHY_TYPE_SATA);

	return regmap_update_bits(miphy_dev->regmap,
				  (unsigned int)miphy_phy->ctrlreg,
				  SYSCFG_SELECT_SATA_MASK,
				  sata << SYSCFG_SELECT_SATA_POS);
}

static int miphy365x_init_pcie_port(struct miphy365x_phy *miphy_phy,
				    struct miphy365x_dev *miphy_dev)
{
	u8 val;

	if (miphy_phy->pcie_tx_pol_inv) {
		/* Invert Tx polarity and clear pci_txdetect_pol bit */
		val = TERM_EN | PCI_EN | DES_BIT_LOCK_EN | TX_POL;
		writeb_relaxed(val, miphy_phy->base + CTRL_REG);
		writeb_relaxed(0x00, miphy_phy->base + PCIE_REG);
	}

	return 0;
}

static inline int miphy365x_hfc_not_rdy(struct miphy365x_phy *miphy_phy,
					struct miphy365x_dev *miphy_dev)
{
	unsigned long timeout = jiffies + msecs_to_jiffies(HFC_TIMEOUT);
	u8 mask = IDLL_RDY | PLL_RDY;
	u8 regval;

	do {
		regval = readb_relaxed(miphy_phy->base + STATUS_REG);
		if (!(regval & mask))
			return 0;

		usleep_range(2000, 2500);
	} while (time_before(jiffies, timeout));

	dev_err(miphy_dev->dev, "HFC ready timeout!\n");
	return -EBUSY;
}

static inline int miphy365x_rdy(struct miphy365x_phy *miphy_phy,
				struct miphy365x_dev *miphy_dev)
{
	unsigned long timeout = jiffies + msecs_to_jiffies(HFC_TIMEOUT);
	u8 mask = IDLL_RDY | PLL_RDY;
	u8 regval;

	do {
		regval = readb_relaxed(miphy_phy->base + STATUS_REG);
		if ((regval & mask) == mask)
			return 0;

		usleep_range(2000, 2500);
	} while (time_before(jiffies, timeout));

	dev_err(miphy_dev->dev, "PHY not ready timeout!\n");
	return -EBUSY;
}

static inline void miphy365x_set_comp(struct miphy365x_phy *miphy_phy,
				      struct miphy365x_dev *miphy_dev)
{
	u8 val, mask;

	if (miphy_phy->sata_gen == SATA_GEN1)
		writeb_relaxed(COMP_2MHZ_RAT_GEN1,
			       miphy_phy->base + COMP_CTRL2_REG);
	else
		writeb_relaxed(COMP_2MHZ_RAT,
			       miphy_phy->base + COMP_CTRL2_REG);

	if (miphy_phy->sata_gen != SATA_GEN3) {
		writeb_relaxed(COMSR_COMP_REF,
			       miphy_phy->base + COMP_CTRL3_REG);
		/*
		 * Force VCO current to value defined by address 0x5A
		 * and disable PCIe100Mref bit
		 * Enable auto load compensation for pll_i_bias
		 */
		writeb_relaxed(BYPASS_PLL_CAL, miphy_phy->base + PLL_CTRL2_REG);
		writeb_relaxed(COMZC_IDLL, miphy_phy->base + COMP_IDLL_REG);
	}

	/*
	 * Force restart compensation and enable auto load
	 * for Comzc_Tx, Comzc_Rx and Comsr on macro
	 */
	val = START_COMSR | START_COMZC | COMP_AUTO_LOAD;
	writeb_relaxed(val, miphy_phy->base + COMP_CTRL1_REG);

	mask = COMSR_DONE | COMZC_DONE;
	while ((readb_relaxed(miphy_phy->base + COMP_CTRL1_REG) & mask)	!= mask)
		cpu_relax();
}

static inline void miphy365x_set_ssc(struct miphy365x_phy *miphy_phy,
				     struct miphy365x_dev *miphy_dev)
{
	u8 val;

	/*
	 * SSC Settings. SSC will be enabled through Link
	 * SSC Ampl. = 0.4%
	 * SSC Freq = 31KHz
	 */
	writeb_relaxed(PLL_SSC_STEP_MSB_VAL,
		       miphy_phy->base + PLL_SSC_STEP_MSB_REG);
	writeb_relaxed(PLL_SSC_STEP_LSB_VAL,
		       miphy_phy->base + PLL_SSC_STEP_LSB_REG);
	writeb_relaxed(PLL_SSC_PER_MSB_VAL,
		       miphy_phy->base + PLL_SSC_PER_MSB_REG);
	writeb_relaxed(PLL_SSC_PER_LSB_VAL,
		       miphy_phy->base + PLL_SSC_PER_LSB_REG);

	/* SSC Settings complete */
	if (miphy_phy->sata_gen == SATA_GEN1) {
		val = PLL_START_CAL | BUF_EN | SYNCHRO_TX | CONFIG_PLL;
		writeb_relaxed(val, miphy_phy->base + PLL_CTRL1_REG);
	} else {
		val = SSC_EN | PLL_START_CAL | BUF_EN | SYNCHRO_TX | CONFIG_PLL;
		writeb_relaxed(val, miphy_phy->base + PLL_CTRL1_REG);
	}
}

static int miphy365x_init_sata_port(struct miphy365x_phy *miphy_phy,
				    struct miphy365x_dev *miphy_dev)
{
	int ret;
	u8 val;

	/*
	 * Force PHY macro reset, PLL calibration reset, PLL reset
	 * and assert Deserializer Reset
	 */
	val = RST_PLL | RST_PLL_CAL | RST_RX | RST_MACRO;
	writeb_relaxed(val, miphy_phy->base + RESET_REG);

	if (miphy_phy->sata_tx_pol_inv)
		writeb_relaxed(TX_POL, miphy_phy->base + CTRL_REG);

	/*
	 * Force macro1 to use rx_lspd, tx_lspd
	 * Force Rx_Clock on first I-DLL phase
	 * Force Des in HP mode on macro, rx_lspd, tx_lspd for Gen2/3
	 */
	writeb_relaxed(SPDSEL_SEL, miphy_phy->base + BOUNDARY1_REG);
	writeb_relaxed(START_CLK_HF, miphy_phy->base + IDLL_TEST_REG);
	val = rx_tx_spd[miphy_phy->sata_gen];
	writeb_relaxed(val, miphy_phy->base + BOUNDARY3_REG);

	/* Wait for HFC_READY = 0 */
	ret = miphy365x_hfc_not_rdy(miphy_phy, miphy_dev);
	if (ret)
		return ret;

	/* Compensation Recalibration */
	miphy365x_set_comp(miphy_phy, miphy_dev);

	switch (miphy_phy->sata_gen) {
	case SATA_GEN3:
		/*
		 * TX Swing target 550-600mv peak to peak diff
		 * Tx Slew target 90-110ps rising/falling time
		 * Rx Eq ON3, Sigdet threshold SDTH1
		 */
		val = PD_VDDTFILTER | CONF_GEN_SEL_GEN3;
		writeb_relaxed(val, miphy_phy->base + BUF_SEL_REG);
		val = SWING_VAL | PREEMPH_VAL;
		writeb_relaxed(val, miphy_phy->base + TXBUF1_REG);
		writeb_relaxed(TXSLEW_VAL, miphy_phy->base + TXBUF2_REG);
		writeb_relaxed(0x00, miphy_phy->base + RXBUF_OFFSET_CTRL_REG);
		val = SDTHRES_VAL | EQ_ON3;
		writeb_relaxed(val, miphy_phy->base + RXBUF_REG);
		break;
	case SATA_GEN2:
		/*
		 * conf gen sel=0x1 to program Gen2 banked registers
		 * VDDT filter ON
		 * Tx Swing target 550-600mV peak-to-peak diff
		 * Tx Slew target 90-110 ps rising/falling time
		 * RX Equalization ON1, Sigdet threshold SDTH1
		 */
		writeb_relaxed(CONF_GEN_SEL_GEN2,
			       miphy_phy->base + BUF_SEL_REG);
		writeb_relaxed(SWING_VAL, miphy_phy->base + TXBUF1_REG);
		writeb_relaxed(TXSLEW_VAL, miphy_phy->base + TXBUF2_REG);
		val = SDTHRES_VAL | EQ_ON1;
		writeb_relaxed(val, miphy_phy->base + RXBUF_REG);
		break;
	case SATA_GEN1:
		/*
		 * conf gen sel = 00b to program Gen1 banked registers
		 * VDDT filter ON
		 * Tx Swing target 500-550mV peak-to-peak diff
		 * Tx Slew target120-140 ps rising/falling time
		 */
		writeb_relaxed(PD_VDDTFILTER, miphy_phy->base + BUF_SEL_REG);
		writeb_relaxed(SWING_VAL_GEN1, miphy_phy->base + TXBUF1_REG);
		writeb_relaxed(TXSLEW_VAL_GEN1,	miphy_phy->base + TXBUF2_REG);
		break;
	default:
		break;
	}

	/* Force Macro1 in partial mode & release pll cal reset */
	writeb_relaxed(RST_RX, miphy_phy->base + RESET_REG);
	usleep_range(100, 150);

	miphy365x_set_ssc(miphy_phy, miphy_dev);

	/* Wait for phy_ready */
	ret = miphy365x_rdy(miphy_phy, miphy_dev);
	if (ret)
		return ret;

	/*
	 * Enable macro1 to use rx_lspd & tx_lspd
	 * Release Rx_Clock on first I-DLL phase on macro1
	 * Assert deserializer reset
	 * des_bit_lock_en is set
	 * bit lock detection strength
	 * Deassert deserializer reset
	 */
	writeb_relaxed(0x00, miphy_phy->base + BOUNDARY1_REG);
	writeb_relaxed(0x00, miphy_phy->base + IDLL_TEST_REG);
	writeb_relaxed(RST_RX, miphy_phy->base + RESET_REG);
	val = miphy_phy->sata_tx_pol_inv ?
		(TX_POL | DES_BIT_LOCK_EN) : DES_BIT_LOCK_EN;
	writeb_relaxed(val, miphy_phy->base + CTRL_REG);

	val = BIT_LOCK_CNT_512 | BIT_LOCK_LEVEL;
	writeb_relaxed(val, miphy_phy->base + DES_BITLOCK_REG);
	writeb_relaxed(0x00, miphy_phy->base + RESET_REG);

	return 0;
}

static int miphy365x_init(struct phy *phy)
{
	struct miphy365x_phy *miphy_phy = phy_get_drvdata(phy);
	struct miphy365x_dev *miphy_dev = dev_get_drvdata(phy->dev.parent);
	int ret = 0;

	mutex_lock(&miphy_dev->miphy_mutex);

	ret = miphy365x_set_path(miphy_phy, miphy_dev);
	if (ret) {
		mutex_unlock(&miphy_dev->miphy_mutex);
		return ret;
	}

	/* Initialise Miphy for PCIe or SATA */
	if (miphy_phy->type == MIPHY_TYPE_PCIE)
		ret = miphy365x_init_pcie_port(miphy_phy, miphy_dev);
	else
		ret = miphy365x_init_sata_port(miphy_phy, miphy_dev);

	mutex_unlock(&miphy_dev->miphy_mutex);

	return ret;
}

int miphy365x_get_addr(struct device *dev, struct miphy365x_phy *miphy_phy,
		       int index)
{
	struct device_node *phynode = miphy_phy->phy->dev.of_node;
	const char *name;
	const __be32 *taddr;
	int type = miphy_phy->type;
	int ret;

	ret = of_property_read_string_index(phynode, "reg-names", index, &name);
	if (ret) {
		dev_err(dev, "no reg-names property not found\n");
		return ret;
	}

	if (!strncmp(name, "syscfg", 6)) {
		taddr = of_get_address(phynode, index, NULL, NULL);
		if (!taddr) {
			dev_err(dev, "failed to fetch syscfg address\n");
			return -EINVAL;
		}

		miphy_phy->ctrlreg = of_translate_address(phynode, taddr);
		if (miphy_phy->ctrlreg == OF_BAD_ADDR) {
			dev_err(dev, "failed to translate syscfg address\n");
			return -EINVAL;
		}

		return 0;
	}

	if (!((!strncmp(name, "sata", 4) && type == MIPHY_TYPE_SATA) ||
	      (!strncmp(name, "pcie", 4) && type == MIPHY_TYPE_PCIE)))
		return 0;

	miphy_phy->base = of_iomap(phynode, index);
	if (!miphy_phy->base) {
		dev_err(dev, "Failed to map %s\n", phynode->full_name);
		return -EINVAL;
	}

	return 0;
}

static struct phy *miphy365x_xlate(struct device *dev,
				   struct of_phandle_args *args)
{
	struct miphy365x_dev *miphy_dev = dev_get_drvdata(dev);
	struct miphy365x_phy *miphy_phy = NULL;
	struct device_node *phynode = args->np;
	int ret, index;

	if (!of_device_is_available(phynode)) {
		dev_warn(dev, "Requested PHY is disabled\n");
		return ERR_PTR(-ENODEV);
	}

	if (args->args_count != 1) {
		dev_err(dev, "Invalid number of cells in 'phy' property\n");
		return ERR_PTR(-EINVAL);
	}

	for (index = 0; index < of_get_child_count(dev->of_node); index++)
		if (phynode == miphy_dev->phys[index]->phy->dev.of_node) {
			miphy_phy = miphy_dev->phys[index];
			break;
		}

	if (!miphy_phy) {
		dev_err(dev, "Failed to find appropriate phy\n");
		return ERR_PTR(-EINVAL);
	}

	miphy_phy->type = args->args[0];

	if (!(miphy_phy->type == MIPHY_TYPE_SATA ||
	      miphy_phy->type == MIPHY_TYPE_PCIE)) {
		dev_err(dev, "Unsupported device type: %d\n", miphy_phy->type);
		return ERR_PTR(-EINVAL);
	}

	/* Each port handles SATA and PCIE - third entry is always sysconf. */
	for (index = 0; index < 3; index++) {
		ret = miphy365x_get_addr(dev, miphy_phy, index);
		if (ret < 0)
			return ERR_PTR(ret);
	}

	return miphy_phy->phy;
}

static struct phy_ops miphy365x_ops = {
	.init		= miphy365x_init,
	.owner		= THIS_MODULE,
};

static int miphy365x_of_probe(struct device_node *phynode,
			      struct miphy365x_phy *miphy_phy)
{
	of_property_read_u32(phynode, "st,sata-gen", &miphy_phy->sata_gen);
	if (!miphy_phy->sata_gen)
		miphy_phy->sata_gen = SATA_GEN1;

	miphy_phy->pcie_tx_pol_inv =
		of_property_read_bool(phynode, "st,pcie-tx-pol-inv");

	miphy_phy->sata_tx_pol_inv =
		of_property_read_bool(phynode, "st,sata-tx-pol-inv");

	return 0;
}

static int miphy365x_probe(struct platform_device *pdev)
{
	struct device_node *child, *np = pdev->dev.of_node;
	struct miphy365x_dev *miphy_dev;
	struct phy_provider *provider;
	struct phy *phy;
	int chancount, port = 0;
	int ret;

	miphy_dev = devm_kzalloc(&pdev->dev, sizeof(*miphy_dev), GFP_KERNEL);
	if (!miphy_dev)
		return -ENOMEM;

	chancount = of_get_child_count(np);
	miphy_dev->phys = devm_kzalloc(&pdev->dev, sizeof(phy) * chancount,
				       GFP_KERNEL);
	if (!miphy_dev->phys)
		return -ENOMEM;

	miphy_dev->regmap = syscon_regmap_lookup_by_phandle(np, "st,syscfg");
	if (IS_ERR(miphy_dev->regmap)) {
		dev_err(miphy_dev->dev, "No syscfg phandle specified\n");
		return PTR_ERR(miphy_dev->regmap);
	}

	miphy_dev->dev = &pdev->dev;

	dev_set_drvdata(&pdev->dev, miphy_dev);

	mutex_init(&miphy_dev->miphy_mutex);

	for_each_child_of_node(np, child) {
		struct miphy365x_phy *miphy_phy;

		miphy_phy = devm_kzalloc(&pdev->dev, sizeof(*miphy_phy),
					 GFP_KERNEL);
		if (!miphy_phy)
			return -ENOMEM;

		miphy_dev->phys[port] = miphy_phy;

		phy = devm_phy_create(&pdev->dev, child, &miphy365x_ops);
		if (IS_ERR(phy)) {
			dev_err(&pdev->dev, "failed to create PHY\n");
			return PTR_ERR(phy);
		}

		miphy_dev->phys[port]->phy = phy;

		ret = miphy365x_of_probe(child, miphy_phy);
		if (ret)
			return ret;

		phy_set_drvdata(phy, miphy_dev->phys[port]);
		port++;
	}

	provider = devm_of_phy_provider_register(&pdev->dev, miphy365x_xlate);
	return PTR_ERR_OR_ZERO(provider);
}

static const struct of_device_id miphy365x_of_match[] = {
	{ .compatible = "st,miphy365x-phy", },
	{ },
};
MODULE_DEVICE_TABLE(of, miphy365x_of_match);

static struct platform_driver miphy365x_driver = {
	.probe	= miphy365x_probe,
	.driver = {
		.name	= "miphy365x-phy",
		.of_match_table	= miphy365x_of_match,
	}
};
module_platform_driver(miphy365x_driver);

MODULE_AUTHOR("Alexandre Torgue <[email protected]>");
MODULE_DESCRIPTION("STMicroelectronics miphy365x driver");
MODULE_LICENSE("GPL v2");
Commit	Line	Data
6e877fed LJ	1	/*
	2	* Copyright (C) 2014 STMicroelectronics – All Rights Reserved
	3	*
	4	* STMicroelectronics PHY driver MiPHY365 (for SoC STiH416).
	5	*
	6	* Authors: Alexandre Torgue <[email protected]>
	7	* Lee Jones <[email protected]>
	8	*
	9	* This program is free software; you can redistribute it and/or modify
	10	* it under the terms of the GNU General Public License version 2, as
	11	* published by the Free Software Foundation.
	12	*
	13	*/
	14
	15	#include <linux/platform_device.h>
	16	#include <linux/io.h>
	17	#include <linux/kernel.h>
	18	#include <linux/module.h>
	19	#include <linux/of.h>
	20	#include <linux/of_platform.h>
7ebdb52e	21	#include <linux/of_address.h>
6e877fed LJ	22	#include <linux/clk.h>
	23	#include <linux/phy/phy.h>
	24	#include <linux/delay.h>
	25	#include <linux/mfd/syscon.h>
	26	#include <linux/regmap.h>
	27
	28	#include <dt-bindings/phy/phy-miphy365x.h>
	29
	30	#define HFC_TIMEOUT 100
	31
7ebdb52e LJ	32	#define SYSCFG_SELECT_SATA_MASK BIT(1)
7ebdb52e LJ	33	#define SYSCFG_SELECT_SATA_POS 1
6e877fed LJ	34
	35	/* MiPHY365x register definitions */
	36	#define RESET_REG 0x00
	37	#define RST_PLL BIT(1)
	38	#define RST_PLL_CAL BIT(2)
	39	#define RST_RX BIT(4)
	40	#define RST_MACRO BIT(7)
	41
	42	#define STATUS_REG 0x01
	43	#define IDLL_RDY BIT(0)
	44	#define PLL_RDY BIT(1)
	45	#define DES_BIT_LOCK BIT(2)
	46	#define DES_SYMBOL_LOCK BIT(3)
	47
	48	#define CTRL_REG 0x02
	49	#define TERM_EN BIT(0)
	50	#define PCI_EN BIT(2)
	51	#define DES_BIT_LOCK_EN BIT(3)
	52	#define TX_POL BIT(5)
	53
	54	#define INT_CTRL_REG 0x03
	55
	56	#define BOUNDARY1_REG 0x10
	57	#define SPDSEL_SEL BIT(0)
	58
	59	#define BOUNDARY3_REG 0x12
	60	#define TX_SPDSEL_GEN1_VAL 0
	61	#define TX_SPDSEL_GEN2_VAL 0x01
	62	#define TX_SPDSEL_GEN3_VAL 0x02
	63	#define RX_SPDSEL_GEN1_VAL 0
	64	#define RX_SPDSEL_GEN2_VAL (0x01 << 3)
	65	#define RX_SPDSEL_GEN3_VAL (0x02 << 3)
	66
	67	#define PCIE_REG 0x16
	68
	69	#define BUF_SEL_REG 0x20
	70	#define CONF_GEN_SEL_GEN3 0x02
	71	#define CONF_GEN_SEL_GEN2 0x01
	72	#define PD_VDDTFILTER BIT(4)
	73
	74	#define TXBUF1_REG 0x21
	75	#define SWING_VAL 0x04
	76	#define SWING_VAL_GEN1 0x03
	77	#define PREEMPH_VAL (0x3 << 5)
	78
	79	#define TXBUF2_REG 0x22
	80	#define TXSLEW_VAL 0x2
	81	#define TXSLEW_VAL_GEN1 0x4
	82
	83	#define RXBUF_OFFSET_CTRL_REG 0x23
	84
	85	#define RXBUF_REG 0x25
	86	#define SDTHRES_VAL 0x01
	87	#define EQ_ON3 (0x03 << 4)
	88	#define EQ_ON1 (0x01 << 4)
	89
	90	#define COMP_CTRL1_REG 0x40
	91	#define START_COMSR BIT(0)
	92	#define START_COMZC BIT(1)
	93	#define COMSR_DONE BIT(2)
	94	#define COMZC_DONE BIT(3)
	95	#define COMP_AUTO_LOAD BIT(4)
	96
	97	#define COMP_CTRL2_REG 0x41
98	#define COMP_2MHZ_RAT_GEN1 0x1e
99	#define COMP_2MHZ_RAT 0xf
100
101	#define COMP_CTRL3_REG 0x42
102	#define COMSR_COMP_REF 0x33
103
104	#define COMP_IDLL_REG 0x47
105	#define COMZC_IDLL 0x2a
106
107	#define PLL_CTRL1_REG 0x50
108	#define PLL_START_CAL BIT(0)
109	#define BUF_EN BIT(2)
110	#define SYNCHRO_TX BIT(3)
111	#define SSC_EN BIT(6)
112	#define CONFIG_PLL BIT(7)
113
114	#define PLL_CTRL2_REG 0x51
115	#define BYPASS_PLL_CAL BIT(1)
116
117	#define PLL_RAT_REG 0x52
118
119	#define PLL_SSC_STEP_MSB_REG 0x56
120	#define PLL_SSC_STEP_MSB_VAL 0x03
121
122	#define PLL_SSC_STEP_LSB_REG 0x57
123	#define PLL_SSC_STEP_LSB_VAL 0x63
124
125	#define PLL_SSC_PER_MSB_REG 0x58
126	#define PLL_SSC_PER_MSB_VAL 0
127
128	#define PLL_SSC_PER_LSB_REG 0x59
129	#define PLL_SSC_PER_LSB_VAL 0xf1
130
131	#define IDLL_TEST_REG 0x72
132	#define START_CLK_HF BIT(6)
133
134	#define DES_BITLOCK_REG 0x86
135	#define BIT_LOCK_LEVEL 0x01
136	#define BIT_LOCK_CNT_512 (0x03 << 5)
137
6e877fed LJ	138	struct miphy365x_phy {
	139	struct phy *phy;
	140	void __iomem *base;
7ebdb52e LJ	141	bool pcie_tx_pol_inv;
	142	bool sata_tx_pol_inv;
	143	u32 sata_gen;
	144	u64 ctrlreg;
6e877fed	145	u8 type;
6e877fed LJ	146	};
	147
	148	struct miphy365x_dev {
	149	struct device *dev;
	150	struct regmap *regmap;
	151	struct mutex miphy_mutex;
7ebdb52e	152	struct miphy365x_phy **phys;
6e877fed LJ	153	};
	154
	155	/*
	156	* These values are represented in Device tree. They are considered to be ABI
	157	* and although they can be extended any existing values must not change.
	158	*/
	159	enum miphy_sata_gen {
	160	SATA_GEN1 = 1,
	161	SATA_GEN2,
	162	SATA_GEN3
	163	};
	164
	165	static u8 rx_tx_spd[] = {
a6cc1b94	166	0, /* GEN0 doesn't exist. */
6e877fed LJ	167	TX_SPDSEL_GEN1_VAL \| RX_SPDSEL_GEN1_VAL,
	168	TX_SPDSEL_GEN2_VAL \| RX_SPDSEL_GEN2_VAL,
	169	TX_SPDSEL_GEN3_VAL \| RX_SPDSEL_GEN3_VAL
	170	};
	171
	172	/*
	173	* This function selects the system configuration,
	174	* either two SATA, one SATA and one PCIe, or two PCIe lanes.
	175	*/
	176	static int miphy365x_set_path(struct miphy365x_phy *miphy_phy,
	177	struct miphy365x_dev *miphy_dev)
	178	{
7ebdb52e	179	bool sata = (miphy_phy->type == MIPHY_TYPE_SATA);
6e877fed	180
7ebdb52e LJ	181	return regmap_update_bits(miphy_dev->regmap,
	182	(unsigned int)miphy_phy->ctrlreg,
	183	SYSCFG_SELECT_SATA_MASK,
	184	sata << SYSCFG_SELECT_SATA_POS);
6e877fed LJ	185	}
	186
	187	static int miphy365x_init_pcie_port(struct miphy365x_phy *miphy_phy,
	188	struct miphy365x_dev *miphy_dev)
	189	{
	190	u8 val;
	191
	192	if (miphy_phy->pcie_tx_pol_inv) {
	193	/* Invert Tx polarity and clear pci_txdetect_pol bit */
	194	val = TERM_EN \| PCI_EN \| DES_BIT_LOCK_EN \| TX_POL;
	195	writeb_relaxed(val, miphy_phy->base + CTRL_REG);
	196	writeb_relaxed(0x00, miphy_phy->base + PCIE_REG);
	197	}
	198
	199	return 0;
	200	}
	201
	202	static inline int miphy365x_hfc_not_rdy(struct miphy365x_phy *miphy_phy,
	203	struct miphy365x_dev *miphy_dev)
	204	{
	205	unsigned long timeout = jiffies + msecs_to_jiffies(HFC_TIMEOUT);
	206	u8 mask = IDLL_RDY \| PLL_RDY;
	207	u8 regval;
	208
	209	do {
	210	regval = readb_relaxed(miphy_phy->base + STATUS_REG);
	211	if (!(regval & mask))
	212	return 0;
	213
	214	usleep_range(2000, 2500);
	215	} while (time_before(jiffies, timeout));
	216
	217	dev_err(miphy_dev->dev, "HFC ready timeout!\n");
	218	return -EBUSY;
	219	}
	220
	221	static inline int miphy365x_rdy(struct miphy365x_phy *miphy_phy,
	222	struct miphy365x_dev *miphy_dev)
	223	{
	224	unsigned long timeout = jiffies + msecs_to_jiffies(HFC_TIMEOUT);
	225	u8 mask = IDLL_RDY \| PLL_RDY;
	226	u8 regval;
	227
	228	do {
	229	regval = readb_relaxed(miphy_phy->base + STATUS_REG);
	230	if ((regval & mask) == mask)
	231	return 0;
	232
	233	usleep_range(2000, 2500);
	234	} while (time_before(jiffies, timeout));
	235
	236	dev_err(miphy_dev->dev, "PHY not ready timeout!\n");
	237	return -EBUSY;
	238	}
	239
	240	static inline void miphy365x_set_comp(struct miphy365x_phy *miphy_phy,
	241	struct miphy365x_dev *miphy_dev)
	242	{
	243	u8 val, mask;
	244
7ebdb52e	245	if (miphy_phy->sata_gen == SATA_GEN1)
6e877fed LJ	246	writeb_relaxed(COMP_2MHZ_RAT_GEN1,
	247	miphy_phy->base + COMP_CTRL2_REG);
	248	else
	249	writeb_relaxed(COMP_2MHZ_RAT,
	250	miphy_phy->base + COMP_CTRL2_REG);
	251
7ebdb52e	252	if (miphy_phy->sata_gen != SATA_GEN3) {
6e877fed LJ	253	writeb_relaxed(COMSR_COMP_REF,
	254	miphy_phy->base + COMP_CTRL3_REG);
	255	/*
	256	* Force VCO current to value defined by address 0x5A
	257	* and disable PCIe100Mref bit
	258	* Enable auto load compensation for pll_i_bias
	259	*/
	260	writeb_relaxed(BYPASS_PLL_CAL, miphy_phy->base + PLL_CTRL2_REG);
	261	writeb_relaxed(COMZC_IDLL, miphy_phy->base + COMP_IDLL_REG);
	262	}
	263
	264	/*
	265	* Force restart compensation and enable auto load
	266	* for Comzc_Tx, Comzc_Rx and Comsr on macro
	267	*/
	268	val = START_COMSR \| START_COMZC \| COMP_AUTO_LOAD;
	269	writeb_relaxed(val, miphy_phy->base + COMP_CTRL1_REG);
	270
	271	mask = COMSR_DONE \| COMZC_DONE;
	272	while ((readb_relaxed(miphy_phy->base + COMP_CTRL1_REG) & mask) != mask)
	273	cpu_relax();
	274	}
	275
	276	static inline void miphy365x_set_ssc(struct miphy365x_phy *miphy_phy,
	277	struct miphy365x_dev *miphy_dev)
	278	{
	279	u8 val;
	280
	281	/*
	282	* SSC Settings. SSC will be enabled through Link
	283	* SSC Ampl. = 0.4%
	284	* SSC Freq = 31KHz
	285	*/
	286	writeb_relaxed(PLL_SSC_STEP_MSB_VAL,
	287	miphy_phy->base + PLL_SSC_STEP_MSB_REG);
	288	writeb_relaxed(PLL_SSC_STEP_LSB_VAL,
	289	miphy_phy->base + PLL_SSC_STEP_LSB_REG);
	290	writeb_relaxed(PLL_SSC_PER_MSB_VAL,
	291	miphy_phy->base + PLL_SSC_PER_MSB_REG);
	292	writeb_relaxed(PLL_SSC_PER_LSB_VAL,
	293	miphy_phy->base + PLL_SSC_PER_LSB_REG);
	294
	295	/* SSC Settings complete */
7ebdb52e	296	if (miphy_phy->sata_gen == SATA_GEN1) {
6e877fed LJ	297	val = PLL_START_CAL \| BUF_EN \| SYNCHRO_TX \| CONFIG_PLL;
	298	writeb_relaxed(val, miphy_phy->base + PLL_CTRL1_REG);
	299	} else {
	300	val = SSC_EN \| PLL_START_CAL \| BUF_EN \| SYNCHRO_TX \| CONFIG_PLL;
	301	writeb_relaxed(val, miphy_phy->base + PLL_CTRL1_REG);
	302	}
	303	}
	304
	305	static int miphy365x_init_sata_port(struct miphy365x_phy *miphy_phy,
	306	struct miphy365x_dev *miphy_dev)
	307	{
	308	int ret;
	309	u8 val;
	310
	311	/*
	312	* Force PHY macro reset, PLL calibration reset, PLL reset
	313	* and assert Deserializer Reset
	314	*/
	315	val = RST_PLL \| RST_PLL_CAL \| RST_RX \| RST_MACRO;
	316	writeb_relaxed(val, miphy_phy->base + RESET_REG);
	317
7ebdb52e	318	if (miphy_phy->sata_tx_pol_inv)
6e877fed LJ	319	writeb_relaxed(TX_POL, miphy_phy->base + CTRL_REG);
	320
	321	/*
	322	* Force macro1 to use rx_lspd, tx_lspd
	323	* Force Rx_Clock on first I-DLL phase
	324	* Force Des in HP mode on macro, rx_lspd, tx_lspd for Gen2/3
	325	*/
	326	writeb_relaxed(SPDSEL_SEL, miphy_phy->base + BOUNDARY1_REG);
	327	writeb_relaxed(START_CLK_HF, miphy_phy->base + IDLL_TEST_REG);
7ebdb52e	328	val = rx_tx_spd[miphy_phy->sata_gen];
6e877fed LJ	329	writeb_relaxed(val, miphy_phy->base + BOUNDARY3_REG);
	330
	331	/* Wait for HFC_READY = 0 */
	332	ret = miphy365x_hfc_not_rdy(miphy_phy, miphy_dev);
	333	if (ret)
	334	return ret;
	335
	336	/* Compensation Recalibration */
	337	miphy365x_set_comp(miphy_phy, miphy_dev);
	338
7ebdb52e	339	switch (miphy_phy->sata_gen) {
6e877fed LJ	340	case SATA_GEN3:
	341	/*
	342	* TX Swing target 550-600mv peak to peak diff
	343	* Tx Slew target 90-110ps rising/falling time
	344	* Rx Eq ON3, Sigdet threshold SDTH1
	345	*/
	346	val = PD_VDDTFILTER \| CONF_GEN_SEL_GEN3;
	347	writeb_relaxed(val, miphy_phy->base + BUF_SEL_REG);
	348	val = SWING_VAL \| PREEMPH_VAL;
	349	writeb_relaxed(val, miphy_phy->base + TXBUF1_REG);
	350	writeb_relaxed(TXSLEW_VAL, miphy_phy->base + TXBUF2_REG);
	351	writeb_relaxed(0x00, miphy_phy->base + RXBUF_OFFSET_CTRL_REG);
	352	val = SDTHRES_VAL \| EQ_ON3;
	353	writeb_relaxed(val, miphy_phy->base + RXBUF_REG);
	354	break;
	355	case SATA_GEN2:
	356	/*
	357	* conf gen sel=0x1 to program Gen2 banked registers
	358	* VDDT filter ON
	359	* Tx Swing target 550-600mV peak-to-peak diff
	360	* Tx Slew target 90-110 ps rising/falling time
	361	* RX Equalization ON1, Sigdet threshold SDTH1
	362	*/
	363	writeb_relaxed(CONF_GEN_SEL_GEN2,
	364	miphy_phy->base + BUF_SEL_REG);
	365	writeb_relaxed(SWING_VAL, miphy_phy->base + TXBUF1_REG);
	366	writeb_relaxed(TXSLEW_VAL, miphy_phy->base + TXBUF2_REG);
	367	val = SDTHRES_VAL \| EQ_ON1;
	368	writeb_relaxed(val, miphy_phy->base + RXBUF_REG);
	369	break;
	370	case SATA_GEN1:
	371	/*
	372	* conf gen sel = 00b to program Gen1 banked registers
	373	* VDDT filter ON
	374	* Tx Swing target 500-550mV peak-to-peak diff
	375	* Tx Slew target120-140 ps rising/falling time
	376	*/
	377	writeb_relaxed(PD_VDDTFILTER, miphy_phy->base + BUF_SEL_REG);
	378	writeb_relaxed(SWING_VAL_GEN1, miphy_phy->base + TXBUF1_REG);
	379	writeb_relaxed(TXSLEW_VAL_GEN1, miphy_phy->base + TXBUF2_REG);
	380	break;
	381	default:
	382	break;
	383	}
	384
	385	/* Force Macro1 in partial mode & release pll cal reset */
	386	writeb_relaxed(RST_RX, miphy_phy->base + RESET_REG);
	387	usleep_range(100, 150);
	388
	389	miphy365x_set_ssc(miphy_phy, miphy_dev);
	390
	391	/* Wait for phy_ready */
	392	ret = miphy365x_rdy(miphy_phy, miphy_dev);
	393	if (ret)
	394	return ret;
	395
	396	/*
	397	* Enable macro1 to use rx_lspd & tx_lspd
	398	* Release Rx_Clock on first I-DLL phase on macro1
	399	* Assert deserializer reset
	400	* des_bit_lock_en is set
	401	* bit lock detection strength
	402	* Deassert deserializer reset
	403	*/
404	writeb_relaxed(0x00, miphy_phy->base + BOUNDARY1_REG);
405	writeb_relaxed(0x00, miphy_phy->base + IDLL_TEST_REG);
406	writeb_relaxed(RST_RX, miphy_phy->base + RESET_REG);
7ebdb52e	407	val = miphy_phy->sata_tx_pol_inv ?
6e877fed LJ	408	(TX_POL \| DES_BIT_LOCK_EN) : DES_BIT_LOCK_EN;
	409	writeb_relaxed(val, miphy_phy->base + CTRL_REG);
	410
	411	val = BIT_LOCK_CNT_512 \| BIT_LOCK_LEVEL;
	412	writeb_relaxed(val, miphy_phy->base + DES_BITLOCK_REG);
	413	writeb_relaxed(0x00, miphy_phy->base + RESET_REG);
	414
	415	return 0;
	416	}
	417
	418	static int miphy365x_init(struct phy *phy)
	419	{
	420	struct miphy365x_phy *miphy_phy = phy_get_drvdata(phy);
	421	struct miphy365x_dev *miphy_dev = dev_get_drvdata(phy->dev.parent);
	422	int ret = 0;
	423
	424	mutex_lock(&miphy_dev->miphy_mutex);
	425
	426	ret = miphy365x_set_path(miphy_phy, miphy_dev);
	427	if (ret) {
	428	mutex_unlock(&miphy_dev->miphy_mutex);
	429	return ret;
	430	}
	431
	432	/* Initialise Miphy for PCIe or SATA */
	433	if (miphy_phy->type == MIPHY_TYPE_PCIE)
	434	ret = miphy365x_init_pcie_port(miphy_phy, miphy_dev);
	435	else
	436	ret = miphy365x_init_sata_port(miphy_phy, miphy_dev);
	437
	438	mutex_unlock(&miphy_dev->miphy_mutex);
	439
	440	return ret;
	441	}
	442
7ebdb52e LJ	443	int miphy365x_get_addr(struct device dev, struct miphy365x_phy miphy_phy,
	444	int index)
	445	{
	446	struct device_node *phynode = miphy_phy->phy->dev.of_node;
	447	const char *name;
	448	const __be32 *taddr;
	449	int type = miphy_phy->type;
	450	int ret;
	451
	452	ret = of_property_read_string_index(phynode, "reg-names", index, &name);
	453	if (ret) {
	454	dev_err(dev, "no reg-names property not found\n");
	455	return ret;
	456	}
	457
	458	if (!strncmp(name, "syscfg", 6)) {
	459	taddr = of_get_address(phynode, index, NULL, NULL);
	460	if (!taddr) {
	461	dev_err(dev, "failed to fetch syscfg address\n");
	462	return -EINVAL;
	463	}
	464
	465	miphy_phy->ctrlreg = of_translate_address(phynode, taddr);
	466	if (miphy_phy->ctrlreg == OF_BAD_ADDR) {
	467	dev_err(dev, "failed to translate syscfg address\n");
	468	return -EINVAL;
	469	}
	470
	471	return 0;
	472	}
	473
	474	if (!((!strncmp(name, "sata", 4) && type == MIPHY_TYPE_SATA) \|\|
	475	(!strncmp(name, "pcie", 4) && type == MIPHY_TYPE_PCIE)))
	476	return 0;
	477
	478	miphy_phy->base = of_iomap(phynode, index);
	479	if (!miphy_phy->base) {
	480	dev_err(dev, "Failed to map %s\n", phynode->full_name);
	481	return -EINVAL;
	482	}
	483
	484	return 0;
	485	}
	486
6e877fed LJ	487	static struct phy miphy365x_xlate(struct device dev,
	488	struct of_phandle_args *args)
	489	{
7ebdb52e LJ	490	struct miphy365x_dev *miphy_dev = dev_get_drvdata(dev);
	491	struct miphy365x_phy *miphy_phy = NULL;
	492	struct device_node *phynode = args->np;
	493	int ret, index;
	494
	495	if (!of_device_is_available(phynode)) {
	496	dev_warn(dev, "Requested PHY is disabled\n");
	497	return ERR_PTR(-ENODEV);
	498	}
6e877fed	499
7ebdb52e	500	if (args->args_count != 1) {
6e877fed LJ	501	dev_err(dev, "Invalid number of cells in 'phy' property\n");
	502	return ERR_PTR(-EINVAL);
	503	}
	504
7ebdb52e LJ	505	for (index = 0; index < of_get_child_count(dev->of_node); index++)
	506	if (phynode == miphy_dev->phys[index]->phy->dev.of_node) {
	507	miphy_phy = miphy_dev->phys[index];
	508	break;
	509	}
	510
	511	if (!miphy_phy) {
	512	dev_err(dev, "Failed to find appropriate phy\n");
6e877fed LJ	513	return ERR_PTR(-EINVAL);
	514	}
	515
7ebdb52e	516	miphy_phy->type = args->args[0];
6e877fed	517
7ebdb52e LJ	518	if (!(miphy_phy->type == MIPHY_TYPE_SATA \|\|
	519	miphy_phy->type == MIPHY_TYPE_PCIE)) {
	520	dev_err(dev, "Unsupported device type: %d\n", miphy_phy->type);
6e877fed LJ	521	return ERR_PTR(-EINVAL);
	522	}
	523
7ebdb52e LJ	524	/* Each port handles SATA and PCIE - third entry is always sysconf. */
	525	for (index = 0; index < 3; index++) {
	526	ret = miphy365x_get_addr(dev, miphy_phy, index);
	527	if (ret < 0)
	528	return ERR_PTR(ret);
	529	}
6e877fed	530
7ebdb52e	531	return miphy_phy->phy;
6e877fed LJ	532	}
	533
	534	static struct phy_ops miphy365x_ops = {
	535	.init = miphy365x_init,
	536	.owner = THIS_MODULE,
	537	};
	538
7ebdb52e LJ	539	static int miphy365x_of_probe(struct device_node *phynode,
7ebdb52e LJ	540	struct miphy365x_phy *miphy_phy)
6e877fed	541	{
7ebdb52e LJ	542	of_property_read_u32(phynode, "st,sata-gen", &miphy_phy->sata_gen);
	543	if (!miphy_phy->sata_gen)
	544	miphy_phy->sata_gen = SATA_GEN1;
6e877fed	545
7ebdb52e LJ	546	miphy_phy->pcie_tx_pol_inv =
7ebdb52e LJ	547	of_property_read_bool(phynode, "st,pcie-tx-pol-inv");
6e877fed	548
7ebdb52e LJ	549	miphy_phy->sata_tx_pol_inv =
7ebdb52e LJ	550	of_property_read_bool(phynode, "st,sata-tx-pol-inv");
6e877fed LJ	551
	552	return 0;
	553	}
	554
	555	static int miphy365x_probe(struct platform_device *pdev)
	556	{
7ebdb52e LJ	557	struct device_node child, np = pdev->dev.of_node;
7ebdb52e LJ	558	struct miphy365x_dev *miphy_dev;
6e877fed	559	struct phy_provider *provider;
7ebdb52e LJ	560	struct phy *phy;
7ebdb52e LJ	561	int chancount, port = 0;
6e877fed LJ	562	int ret;
6e877fed LJ	563
7ebdb52e LJ	564	miphy_dev = devm_kzalloc(&pdev->dev, sizeof(*miphy_dev), GFP_KERNEL);
7ebdb52e LJ	565	if (!miphy_dev)
6e877fed LJ	566	return -ENOMEM;
6e877fed LJ	567
7ebdb52e LJ	568	chancount = of_get_child_count(np);
	569	miphy_dev->phys = devm_kzalloc(&pdev->dev, sizeof(phy) * chancount,
	570	GFP_KERNEL);
	571	if (!miphy_dev->phys)
	572	return -ENOMEM;
	573
	574	miphy_dev->regmap = syscon_regmap_lookup_by_phandle(np, "st,syscfg");
	575	if (IS_ERR(miphy_dev->regmap)) {
	576	dev_err(miphy_dev->dev, "No syscfg phandle specified\n");
	577	return PTR_ERR(miphy_dev->regmap);
	578	}
	579
	580	miphy_dev->dev = &pdev->dev;
	581
	582	dev_set_drvdata(&pdev->dev, miphy_dev);
6e877fed	583
7ebdb52e	584	mutex_init(&miphy_dev->miphy_mutex);
6e877fed	585
7ebdb52e LJ	586	for_each_child_of_node(np, child) {
7ebdb52e LJ	587	struct miphy365x_phy *miphy_phy;
6e877fed	588
7ebdb52e LJ	589	miphy_phy = devm_kzalloc(&pdev->dev, sizeof(*miphy_phy),
	590	GFP_KERNEL);
	591	if (!miphy_phy)
	592	return -ENOMEM;
6e877fed	593
7ebdb52e	594	miphy_dev->phys[port] = miphy_phy;
6e877fed	595
dbc98635	596	phy = devm_phy_create(&pdev->dev, child, &miphy365x_ops);
6e877fed	597	if (IS_ERR(phy)) {
7ebdb52e	598	dev_err(&pdev->dev, "failed to create PHY\n");
6e877fed LJ	599	return PTR_ERR(phy);
	600	}
	601
7ebdb52e	602	miphy_dev->phys[port]->phy = phy;
6e877fed	603
7ebdb52e	604	ret = miphy365x_of_probe(child, miphy_phy);
6e877fed LJ	605	if (ret)
	606	return ret;
	607
7ebdb52e LJ	608	phy_set_drvdata(phy, miphy_dev->phys[port]);
7ebdb52e LJ	609	port++;
6e877fed LJ	610	}
6e877fed LJ	611
7ebdb52e	612	provider = devm_of_phy_provider_register(&pdev->dev, miphy365x_xlate);
c1fc0050	613	return PTR_ERR_OR_ZERO(provider);
6e877fed LJ	614	}
	615
	616	static const struct of_device_id miphy365x_of_match[] = {
	617	{ .compatible = "st,miphy365x-phy", },
	618	{ },
	619	};
	620	MODULE_DEVICE_TABLE(of, miphy365x_of_match);
	621
	622	static struct platform_driver miphy365x_driver = {
	623	.probe = miphy365x_probe,
	624	.driver = {
	625	.name = "miphy365x-phy",
6e877fed LJ	626	.of_match_table = miphy365x_of_match,
	627	}
	628	};
	629	module_platform_driver(miphy365x_driver);
	630
	631	MODULE_AUTHOR("Alexandre Torgue <[email protected]>");
	632	MODULE_DESCRIPTION("STMicroelectronics miphy365x driver");
	633	MODULE_LICENSE("GPL v2");