projects / linux.git / blame
| Commit | Line | Data |
|---|---|---|
| 37ab3564 VK |
1 | Kernel driver pxe1610 |
| 2 | ===================== | |
| 3 | ||
| 4 | Supported chips: | |
| 899df7b4 | 5 | |
| 37ab3564 | 6 | * Infineon PXE1610 |
| 899df7b4 | 7 | |
| 37ab3564 | 8 | Prefix: 'pxe1610' |
| 899df7b4 | 9 | |
| 37ab3564 | 10 | Addresses scanned: - |
| 899df7b4 | 11 | |
| 37ab3564 VK |
12 | Datasheet: Datasheet is not publicly available. |
| 13 | ||
| 14 | * Infineon PXE1110 | |
| 899df7b4 | 15 | |
| 37ab3564 | 16 | Prefix: 'pxe1110' |
| 899df7b4 | 17 | |
| 37ab3564 | 18 | Addresses scanned: - |
| 899df7b4 | 19 | |
| 37ab3564 VK |
20 | Datasheet: Datasheet is not publicly available. |
| 21 | ||
| 22 | * Infineon PXM1310 | |
| 899df7b4 | 23 | |
| 37ab3564 | 24 | Prefix: 'pxm1310' |
| 899df7b4 | 25 | |
| 37ab3564 | 26 | Addresses scanned: - |
| 899df7b4 | 27 | |
| 37ab3564 VK |
28 | Datasheet: Datasheet is not publicly available. |
| 29 | ||
| 30 | Author: Vijay Khemka <[email protected]> | |
| 31 | ||
| 32 | ||
| 33 | Description | |
| 34 | ----------- | |
| 35 | ||
| 36 | PXE1610/PXE1110 are Multi-rail/Multiphase Digital Controllers | |
| 37 | and compliant to | |
| 899df7b4 MCC |
38 | |
| 39 | - Intel VR13 DC-DC converter specifications. | |
| 40 | - Intel SVID protocol. | |
| 41 | ||
| 37ab3564 | 42 | Used for Vcore power regulation for Intel VR13 based microprocessors |
| 899df7b4 MCC |
43 | |
| 44 | - Servers, Workstations, and High-end desktops | |
| 37ab3564 VK |
45 | |
| 46 | PXM1310 is a Multi-rail Controller and it is compliant to | |
| 899df7b4 MCC |
47 | |
| 48 | - Intel VR13 DC-DC converter specifications. | |
| 49 | - Intel SVID protocol. | |
| 50 | ||
| 37ab3564 VK |
51 | Used for DDR3/DDR4 Memory power regulation for Intel VR13 and |
| 52 | IMVP8 based systems | |
| 53 | ||
| 54 | ||
| 55 | Usage Notes | |
| 56 | ----------- | |
| 57 | ||
| 58 | This driver does not probe for PMBus devices. You will have | |
| 59 | to instantiate devices explicitly. | |
| 60 | ||
| 61 | Example: the following commands will load the driver for an PXE1610 | |
| 899df7b4 | 62 | at address 0x70 on I2C bus #4:: |
| 37ab3564 | 63 | |
| 899df7b4 MCC |
64 | # modprobe pxe1610 |
| 65 | # echo pxe1610 0x70 > /sys/bus/i2c/devices/i2c-4/new_device | |
| 37ab3564 VK |
66 | |
| 67 | It can also be instantiated by declaring in device tree | |
| 68 | ||
| 69 | ||
| 70 | Sysfs attributes | |
| 71 | ---------------- | |
| 72 | ||
| 899df7b4 | 73 | ====================== ==================================== |
| 37ab3564 VK |
74 | curr1_label "iin" |
| 75 | curr1_input Measured input current | |
| 76 | curr1_alarm Current high alarm | |
| 77 | ||
| 78 | curr[2-4]_label "iout[1-3]" | |
| 79 | curr[2-4]_input Measured output current | |
| 80 | curr[2-4]_crit Critical maximum current | |
| 81 | curr[2-4]_crit_alarm Current critical high alarm | |
| 82 | ||
| 83 | in1_label "vin" | |
| 84 | in1_input Measured input voltage | |
| 85 | in1_crit Critical maximum input voltage | |
| 86 | in1_crit_alarm Input voltage critical high alarm | |
| 87 | ||
| 88 | in[2-4]_label "vout[1-3]" | |
| 89 | in[2-4]_input Measured output voltage | |
| 90 | in[2-4]_lcrit Critical minimum output voltage | |
| 91 | in[2-4]_lcrit_alarm Output voltage critical low alarm | |
| 92 | in[2-4]_crit Critical maximum output voltage | |
| 93 | in[2-4]_crit_alarm Output voltage critical high alarm | |
| 94 | ||
| 95 | power1_label "pin" | |
| 96 | power1_input Measured input power | |
| 97 | power1_alarm Input power high alarm | |
| 98 | ||
| 99 | power[2-4]_label "pout[1-3]" | |
| 100 | power[2-4]_input Measured output power | |
| 101 | ||
| 102 | temp[1-3]_input Measured temperature | |
| 103 | temp[1-3]_crit Critical high temperature | |
| 104 | temp[1-3]_crit_alarm Chip temperature critical high alarm | |
| 105 | temp[1-3]_max Maximum temperature | |
| 106 | temp[1-3]_max_alarm Chip temperature high alarm | |
| 899df7b4 | 107 | ====================== ==================================== |