[linux.git] / drivers / atm / Kconfig

# SPDX-License-Identifier: GPL-2.0
#
# ATM device configuration
#

menuconfig ATM_DRIVERS
	bool "ATM drivers"
	depends on NETDEVICES && ATM
	default y
	help
	  Say Y here to get to see options for Asynchronous Transfer Mode
	  device drivers. This option alone does not add any kernel code.

	  If you say N, all options in this submenu will be skipped and disabled.

if ATM_DRIVERS && NETDEVICES && ATM

config ATM_DUMMY
	tristate "Dummy ATM driver"
	help
	  Dummy ATM driver. Useful for proxy signalling, testing,
	  and development.  If unsure, say N.

config ATM_TCP
	tristate "ATM over TCP"
	depends on INET
	help
	  ATM over TCP driver. Useful mainly for development and for
	  experiments. If unsure, say N.

config ATM_LANAI
	tristate "Efficient Networks Speedstream 3010"
	depends on PCI && ATM
	help
	  Supports ATM cards based on the Efficient Networks "Lanai"
	  chipset such as the Speedstream 3010 and the ENI-25p.  The
	  Speedstream 3060 is currently not supported since we don't
	  have the code to drive the on-board Alcatel DSL chipset (yet).

config ATM_ENI
	tristate "Efficient Networks ENI155P"
	depends on PCI
	help
	  Driver for the Efficient Networks ENI155p series and SMC ATM
	  Power155 155 Mbps ATM adapters. Both, the versions with 512KB and
	  2MB on-board RAM (Efficient calls them "C" and "S", respectively),
	  and the FPGA and the ASIC Tonga versions of the board are supported.
	  The driver works with MMF (-MF or ...F) and UTP-5 (-U5 or ...D)
	  adapters.

	  To compile this driver as a module, choose M here: the module will
	  be called eni.

config ATM_ENI_DEBUG
	bool "Enable extended debugging"
	depends on ATM_ENI
	help
	  Extended debugging records various events and displays that list
	  when an inconsistency is detected. This mechanism is faster than
	  generally using printks, but still has some impact on performance.
	  Note that extended debugging may create certain race conditions
	  itself. Enable this ONLY if you suspect problems with the driver.

config ATM_ENI_TUNE_BURST
	bool "Fine-tune burst settings"
	depends on ATM_ENI
	help
	  In order to obtain good throughput, the ENI NIC can transfer
	  multiple words of data per PCI bus access cycle. Such a multi-word
	  transfer is called a burst.

	  The default settings for the burst sizes are suitable for most PCI
	  chipsets. However, in some cases, large bursts may overrun buffers
	  in the PCI chipset and cause data corruption. In such cases, large
	  bursts must be disabled and only (slower) small bursts can be used.
	  The burst sizes can be set independently in the send (TX) and
	  receive (RX) direction.

	  Note that enabling many different burst sizes in the same direction
	  may increase the cost of setting up a transfer such that the
	  resulting throughput is lower than when using only the largest
	  available burst size.

	  Also, sometimes larger bursts lead to lower throughput, e.g. on an
	  Intel 440FX board, a drop from 135 Mbps to 103 Mbps was observed
	  when going from 8W to 16W bursts.

config ATM_ENI_BURST_TX_16W
	bool "Enable 16W TX bursts (discouraged)"
	depends on ATM_ENI_TUNE_BURST
	help
	  Burst sixteen words at once in the send direction. This may work
	  with recent PCI chipsets, but is known to fail with older chipsets.

config ATM_ENI_BURST_TX_8W
	bool "Enable 8W TX bursts (recommended)"
	depends on ATM_ENI_TUNE_BURST
	help
	  Burst eight words at once in the send direction. This is the default
	  setting.

config ATM_ENI_BURST_TX_4W
	bool "Enable 4W TX bursts (optional)"
	depends on ATM_ENI_TUNE_BURST
	help
	  Burst four words at once in the send direction. You may want to try
	  this if you have disabled 8W bursts. Enabling 4W if 8W is also set
	  may or may not improve throughput.

config ATM_ENI_BURST_TX_2W
	bool "Enable 2W TX bursts (optional)"
	depends on ATM_ENI_TUNE_BURST
	help
	  Burst two words at once in the send direction. You may want to try
	  this if you have disabled 4W and 8W bursts. Enabling 2W if 4W or 8W
	  are also set may or may not improve throughput.

config ATM_ENI_BURST_RX_16W
	bool "Enable 16W RX bursts (discouraged)"
	depends on ATM_ENI_TUNE_BURST
	help
	  Burst sixteen words at once in the receive direction. This may work
	  with recent PCI chipsets, but is known to fail with older chipsets.

config ATM_ENI_BURST_RX_8W
	bool "Enable 8W RX bursts (discouraged)"
	depends on ATM_ENI_TUNE_BURST
	help
	  Burst eight words at once in the receive direction. This may work
	  with recent PCI chipsets, but is known to fail with older chipsets,
	  such as the Intel Neptune series.

config ATM_ENI_BURST_RX_4W
	bool "Enable 4W RX bursts (recommended)"
	depends on ATM_ENI_TUNE_BURST
	help
	  Burst four words at once in the receive direction. This is the
	  default setting. Enabling 4W if 8W is also set may or may not
	  improve throughput.

config ATM_ENI_BURST_RX_2W
	bool "Enable 2W RX bursts (optional)"
	depends on ATM_ENI_TUNE_BURST
	help
	  Burst two words at once in the receive direction. You may want to
	  try this if you have disabled 4W and 8W bursts. Enabling 2W if 4W or
	  8W are also set may or may not improve throughput.

config ATM_NICSTAR
	tristate "IDT 77201 (NICStAR) (ForeRunnerLE)"
	depends on PCI
	help
	  The NICStAR chipset family is used in a large number of ATM NICs for
	  25 and for 155 Mbps, including IDT cards and the Fore ForeRunnerLE
	  series. Say Y if you have one of those.

	  To compile this driver as a module, choose M here: the module will
	  be called nicstar.

config ATM_NICSTAR_USE_SUNI
	bool "Use suni PHY driver (155Mbps)"
	depends on ATM_NICSTAR
	help
	  Support for the S-UNI and compatible PHYsical layer chips. These are
	  found in most 155Mbps NICStAR based ATM cards, namely in the
	  ForeRunner LE155 cards. This driver provides detection of cable~
	  removal and reinsertion and provides some statistics. This driver
	  doesn't have removal capability when compiled as a module, so if you
	  need that capability don't include S-UNI support (it's not needed to
	  make the card work).

config ATM_NICSTAR_USE_IDT77105
	bool "Use IDT77105 PHY driver (25Mbps)"
	depends on ATM_NICSTAR
	help
	  Support for the PHYsical layer chip in ForeRunner LE25 cards. In
	  addition to cable removal/reinsertion detection, this driver allows
	  you to control the loopback mode of the chip via a dedicated IOCTL.
	  This driver is required for proper handling of temporary carrier
	  loss, so if you have a 25Mbps NICStAR based ATM card you must say Y.

config ATM_IDT77252
	tristate "IDT 77252 (NICStAR II)"
	depends on PCI
	help
	  Driver for the IDT 77252 ATM PCI chips.

	  To compile this driver as a module, choose M here: the module will
	  be called idt77252.

config ATM_IDT77252_DEBUG
	bool "Enable debugging messages"
	depends on ATM_IDT77252
	help
	  Somewhat useful debugging messages are available. The choice of
	  messages is controlled by a bitmap.  This may be specified as a
	  module argument.  See the file <file:drivers/atm/idt77252.h> for
	  the meanings of the bits in the mask.

	  When active, these messages can have a significant impact on the
	  speed of the driver, and the size of your syslog files! When
	  inactive, they will have only a modest impact on performance.

config ATM_IDT77252_RCV_ALL
	bool "Receive ALL cells in raw queue"
	depends on ATM_IDT77252
	help
	  Enable receiving of all cells on the ATM link, that do not match
	  an open connection in the raw cell queue of the driver.  Useful
	  for debugging or special applications only, so the safe answer is N.

config ATM_IDT77252_USE_SUNI
	bool
	depends on ATM_IDT77252
	default y

config ATM_IA
	tristate "Interphase ATM PCI x575/x525/x531"
	depends on PCI
	help
	  This is a driver for the Interphase (i)ChipSAR adapter cards
	  which include a variety of variants in term of the size of the
	  control memory (128K-1KVC, 512K-4KVC), the size of the packet
	  memory (128K, 512K, 1M), and the PHY type (Single/Multi mode OC3,
	  UTP155, UTP25, DS3 and E3). Go to:
	  	<http://www.iphase.com/>
	  for more info about the cards. Say Y (or M to compile as a module
	  named iphase) here if you have one of these cards.

	  See the file
	  <file:Documentation/networking/device_drivers/atm/iphase.rst>
	  for further details.

config ATM_IA_DEBUG
	bool "Enable debugging messages"
	depends on ATM_IA
	help
	  Somewhat useful debugging messages are available. The choice of
	  messages is controlled by a bitmap. This may be specified as a
	  module argument (kernel command line argument as well?), changed
	  dynamically using an ioctl (Get the debug utility, iadbg, from
	  <ftp://ftp.iphase.com/pub/atm/pci/>).

	  See the file <file:drivers/atm/iphase.h> for the meanings of the
	  bits in the mask.

	  When active, these messages can have a significant impact on the
	  speed of the driver, and the size of your syslog files! When
	  inactive, they will have only a modest impact on performance.

config ATM_FORE200E
	tristate "FORE Systems 200E-series"
	depends on (PCI || SBUS)
	select FW_LOADER
	help
	  This is a driver for the FORE Systems 200E-series ATM adapter
	  cards. It simultaneously supports PCA-200E and SBA-200E models
	  on PCI and SBUS hosts. Say Y (or M to compile as a module
	  named fore_200e) here if you have one of these ATM adapters.

	  See the file
	  <file:Documentation/networking/device_drivers/atm/fore200e.rst> for
	  further details.

config ATM_FORE200E_USE_TASKLET
	bool "Defer interrupt work to a tasklet"
	depends on ATM_FORE200E
	default n
	help
	  This defers work to be done by the interrupt handler to a
	  tasklet instead of handling everything at interrupt time.  This
	  may improve the responsive of the host.

config ATM_FORE200E_TX_RETRY
	int "Maximum number of tx retries"
	depends on ATM_FORE200E
	default "16"
	help
	  Specifies the number of times the driver attempts to transmit
	  a message before giving up, if the transmit queue of the ATM card
	  is transiently saturated.

	  Saturation of the transmit queue may occur only under extreme
	  conditions, e.g. when a fast host continuously submits very small
	  frames (<64 bytes) or raw AAL0 cells (48 bytes) to the ATM adapter.

	  Note that under common conditions, it is unlikely that you encounter
	  a saturation of the transmit queue, so the retry mechanism never
	  comes into play.

config ATM_FORE200E_DEBUG
	int "Debugging level (0-3)"
	depends on ATM_FORE200E
	default "0"
	help
	  Specifies the level of debugging messages issued by the driver.
	  The verbosity of the driver increases with the value of this
	  parameter.

	  When active, these messages can have a significant impact on
	  the performances of the driver, and the size of your syslog files!
	  Keep the debugging level to 0 during normal operations.

config ATM_HE
	tristate "ForeRunner HE Series"
	depends on PCI
	help
	  This is a driver for the Marconi ForeRunner HE-series ATM adapter
	  cards. It simultaneously supports the 155 and 622 versions.

config ATM_HE_USE_SUNI
	bool "Use S/UNI PHY driver"
	depends on ATM_HE
	help
	  Support for the S/UNI-Ultra and S/UNI-622 found in the ForeRunner
	  HE cards.  This driver provides carrier detection some statistics.

config ATM_SOLOS
	tristate "Solos ADSL2+ PCI Multiport card driver"
	depends on PCI
	select FW_LOADER
	help
	  Support for the Solos multiport ADSL2+ card.

endif # ATM
Commit	Line	Data
b2441318	1	# SPDX-License-Identifier: GPL-2.0
1da177e4 LT	2	#
	3	# ATM device configuration
	4	#
	5
4151ce31 JE	6	menuconfig ATM_DRIVERS
4151ce31 JE	7	bool "ATM drivers"
1da177e4	8	depends on NETDEVICES && ATM
4151ce31	9	default y
a7f7f624	10	help
06bfb7eb JE	11	Say Y here to get to see options for Asynchronous Transfer Mode
	12	device drivers. This option alone does not add any kernel code.
	13
	14	If you say N, all options in this submenu will be skipped and disabled.
4151ce31	15
59faba1b	16	if ATM_DRIVERS && NETDEVICES && ATM
1da177e4	17
fb296449 CW	18	config ATM_DUMMY
fb296449 CW	19	tristate "Dummy ATM driver"
fb296449 CW	20	help
	21	Dummy ATM driver. Useful for proxy signalling, testing,
	22	and development. If unsure, say N.
	23
1da177e4 LT	24	config ATM_TCP
1da177e4 LT	25	tristate "ATM over TCP"
4151ce31	26	depends on INET
1da177e4 LT	27	help
	28	ATM over TCP driver. Useful mainly for development and for
	29	experiments. If unsure, say N.
	30
	31	config ATM_LANAI
	32	tristate "Efficient Networks Speedstream 3010"
	33	depends on PCI && ATM
	34	help
	35	Supports ATM cards based on the Efficient Networks "Lanai"
	36	chipset such as the Speedstream 3010 and the ENI-25p. The
	37	Speedstream 3060 is currently not supported since we don't
	38	have the code to drive the on-board Alcatel DSL chipset (yet).
	39
	40	config ATM_ENI
	41	tristate "Efficient Networks ENI155P"
4151ce31	42	depends on PCI
a7f7f624	43	help
1da177e4 LT	44	Driver for the Efficient Networks ENI155p series and SMC ATM
	45	Power155 155 Mbps ATM adapters. Both, the versions with 512KB and
	46	2MB on-board RAM (Efficient calls them "C" and "S", respectively),
	47	and the FPGA and the ASIC Tonga versions of the board are supported.
	48	The driver works with MMF (-MF or ...F) and UTP-5 (-U5 or ...D)
	49	adapters.
	50
	51	To compile this driver as a module, choose M here: the module will
	52	be called eni.
	53
	54	config ATM_ENI_DEBUG
	55	bool "Enable extended debugging"
	56	depends on ATM_ENI
	57	help
	58	Extended debugging records various events and displays that list
	59	when an inconsistency is detected. This mechanism is faster than
	60	generally using printks, but still has some impact on performance.
	61	Note that extended debugging may create certain race conditions
	62	itself. Enable this ONLY if you suspect problems with the driver.
	63
	64	config ATM_ENI_TUNE_BURST
	65	bool "Fine-tune burst settings"
	66	depends on ATM_ENI
a7f7f624	67	help
1da177e4 LT	68	In order to obtain good throughput, the ENI NIC can transfer
	69	multiple words of data per PCI bus access cycle. Such a multi-word
	70	transfer is called a burst.
	71
	72	The default settings for the burst sizes are suitable for most PCI
	73	chipsets. However, in some cases, large bursts may overrun buffers
	74	in the PCI chipset and cause data corruption. In such cases, large
	75	bursts must be disabled and only (slower) small bursts can be used.
	76	The burst sizes can be set independently in the send (TX) and
	77	receive (RX) direction.
	78
	79	Note that enabling many different burst sizes in the same direction
	80	may increase the cost of setting up a transfer such that the
	81	resulting throughput is lower than when using only the largest
	82	available burst size.
	83
	84	Also, sometimes larger bursts lead to lower throughput, e.g. on an
	85	Intel 440FX board, a drop from 135 Mbps to 103 Mbps was observed
	86	when going from 8W to 16W bursts.
	87
	88	config ATM_ENI_BURST_TX_16W
	89	bool "Enable 16W TX bursts (discouraged)"
	90	depends on ATM_ENI_TUNE_BURST
	91	help
	92	Burst sixteen words at once in the send direction. This may work
	93	with recent PCI chipsets, but is known to fail with older chipsets.
	94
	95	config ATM_ENI_BURST_TX_8W
	96	bool "Enable 8W TX bursts (recommended)"
	97	depends on ATM_ENI_TUNE_BURST
	98	help
	99	Burst eight words at once in the send direction. This is the default
	100	setting.
	101
	102	config ATM_ENI_BURST_TX_4W
	103	bool "Enable 4W TX bursts (optional)"
	104	depends on ATM_ENI_TUNE_BURST
	105	help
	106	Burst four words at once in the send direction. You may want to try
	107	this if you have disabled 8W bursts. Enabling 4W if 8W is also set
	108	may or may not improve throughput.
	109
	110	config ATM_ENI_BURST_TX_2W
	111	bool "Enable 2W TX bursts (optional)"
	112	depends on ATM_ENI_TUNE_BURST
	113	help
	114	Burst two words at once in the send direction. You may want to try
	115	this if you have disabled 4W and 8W bursts. Enabling 2W if 4W or 8W
	116	are also set may or may not improve throughput.
	117
	118	config ATM_ENI_BURST_RX_16W
	119	bool "Enable 16W RX bursts (discouraged)"
	120	depends on ATM_ENI_TUNE_BURST
	121	help
	122	Burst sixteen words at once in the receive direction. This may work
	123	with recent PCI chipsets, but is known to fail with older chipsets.
	124
	125	config ATM_ENI_BURST_RX_8W
	126	bool "Enable 8W RX bursts (discouraged)"
	127	depends on ATM_ENI_TUNE_BURST
	128	help
	129	Burst eight words at once in the receive direction. This may work
	130	with recent PCI chipsets, but is known to fail with older chipsets,
	131	such as the Intel Neptune series.
132
133	config ATM_ENI_BURST_RX_4W
134	bool "Enable 4W RX bursts (recommended)"
135	depends on ATM_ENI_TUNE_BURST
136	help
137	Burst four words at once in the receive direction. This is the
138	default setting. Enabling 4W if 8W is also set may or may not
139	improve throughput.
140
141	config ATM_ENI_BURST_RX_2W
142	bool "Enable 2W RX bursts (optional)"
143	depends on ATM_ENI_TUNE_BURST
144	help
145	Burst two words at once in the receive direction. You may want to
146	try this if you have disabled 4W and 8W bursts. Enabling 2W if 4W or
147	8W are also set may or may not improve throughput.
148
1da177e4 LT	149	config ATM_NICSTAR
1da177e4 LT	150	tristate "IDT 77201 (NICStAR) (ForeRunnerLE)"
864a3ff6	151	depends on PCI
1da177e4 LT	152	help
	153	The NICStAR chipset family is used in a large number of ATM NICs for
	154	25 and for 155 Mbps, including IDT cards and the Fore ForeRunnerLE
	155	series. Say Y if you have one of those.
	156
	157	To compile this driver as a module, choose M here: the module will
	158	be called nicstar.
	159
	160	config ATM_NICSTAR_USE_SUNI
	161	bool "Use suni PHY driver (155Mbps)"
	162	depends on ATM_NICSTAR
	163	help
	164	Support for the S-UNI and compatible PHYsical layer chips. These are
	165	found in most 155Mbps NICStAR based ATM cards, namely in the
	166	ForeRunner LE155 cards. This driver provides detection of cable~
	167	removal and reinsertion and provides some statistics. This driver
	168	doesn't have removal capability when compiled as a module, so if you
	169	need that capability don't include S-UNI support (it's not needed to
	170	make the card work).
	171
	172	config ATM_NICSTAR_USE_IDT77105
cd9d4ff9	173	bool "Use IDT77105 PHY driver (25Mbps)"
1da177e4 LT	174	depends on ATM_NICSTAR
	175	help
	176	Support for the PHYsical layer chip in ForeRunner LE25 cards. In
	177	addition to cable removal/reinsertion detection, this driver allows
	178	you to control the loopback mode of the chip via a dedicated IOCTL.
	179	This driver is required for proper handling of temporary carrier
	180	loss, so if you have a 25Mbps NICStAR based ATM card you must say Y.
	181
	182	config ATM_IDT77252
	183	tristate "IDT 77252 (NICStAR II)"
4151ce31	184	depends on PCI
1da177e4 LT	185	help
	186	Driver for the IDT 77252 ATM PCI chips.
	187
	188	To compile this driver as a module, choose M here: the module will
	189	be called idt77252.
	190
	191	config ATM_IDT77252_DEBUG
	192	bool "Enable debugging messages"
	193	depends on ATM_IDT77252
	194	help
	195	Somewhat useful debugging messages are available. The choice of
	196	messages is controlled by a bitmap. This may be specified as a
	197	module argument. See the file <file:drivers/atm/idt77252.h> for
	198	the meanings of the bits in the mask.
	199
	200	When active, these messages can have a significant impact on the
	201	speed of the driver, and the size of your syslog files! When
	202	inactive, they will have only a modest impact on performance.
	203
	204	config ATM_IDT77252_RCV_ALL
	205	bool "Receive ALL cells in raw queue"
	206	depends on ATM_IDT77252
	207	help
	208	Enable receiving of all cells on the ATM link, that do not match
	209	an open connection in the raw cell queue of the driver. Useful
	210	for debugging or special applications only, so the safe answer is N.
	211
	212	config ATM_IDT77252_USE_SUNI
	213	bool
	214	depends on ATM_IDT77252
	215	default y
	216
1da177e4 LT	217	config ATM_IA
1da177e4 LT	218	tristate "Interphase ATM PCI x575/x525/x531"
97928f70	219	depends on PCI
a7f7f624	220	help
1da177e4 LT	221	This is a driver for the Interphase (i)ChipSAR adapter cards
	222	which include a variety of variants in term of the size of the
	223	control memory (128K-1KVC, 512K-4KVC), the size of the packet
	224	memory (128K, 512K, 1M), and the PHY type (Single/Multi mode OC3,
	225	UTP155, UTP25, DS3 and E3). Go to:
631dd1a8	226	<http://www.iphase.com/>
1da177e4 LT	227	for more info about the cards. Say Y (or M to compile as a module
	228	named iphase) here if you have one of these cards.
	229
9633a0e9 JK	230	See the file
	231	<file:Documentation/networking/device_drivers/atm/iphase.rst>
	232	for further details.
1da177e4 LT	233
	234	config ATM_IA_DEBUG
	235	bool "Enable debugging messages"
	236	depends on ATM_IA
a7f7f624	237	help
1da177e4 LT	238	Somewhat useful debugging messages are available. The choice of
	239	messages is controlled by a bitmap. This may be specified as a
	240	module argument (kernel command line argument as well?), changed
	241	dynamically using an ioctl (Get the debug utility, iadbg, from
	242	<ftp://ftp.iphase.com/pub/atm/pci/>).
	243
	244	See the file <file:drivers/atm/iphase.h> for the meanings of the
	245	bits in the mask.
	246
	247	When active, these messages can have a significant impact on the
	248	speed of the driver, and the size of your syslog files! When
	249	inactive, they will have only a modest impact on performance.
	250
e92481f9	251	config ATM_FORE200E
1da177e4	252	tristate "FORE Systems 200E-series"
e92481f9 CW	253	depends on (PCI \|\| SBUS)
e92481f9 CW	254	select FW_LOADER
a7f7f624	255	help
1da177e4 LT	256	This is a driver for the FORE Systems 200E-series ATM adapter
	257	cards. It simultaneously supports PCA-200E and SBA-200E models
	258	on PCI and SBUS hosts. Say Y (or M to compile as a module
	259	named fore_200e) here if you have one of these ATM adapters.
	260
9633a0e9 JK	261	See the file
9633a0e9 JK	262	<file:Documentation/networking/device_drivers/atm/fore200e.rst> for
1da177e4 LT	263	further details.
1da177e4 LT	264
1da177e4 LT	265	config ATM_FORE200E_USE_TASKLET
1da177e4 LT	266	bool "Defer interrupt work to a tasklet"
e92481f9	267	depends on ATM_FORE200E
1da177e4 LT	268	default n
	269	help
	270	This defers work to be done by the interrupt handler to a
00181fc9	271	tasklet instead of handling everything at interrupt time. This
1da177e4 LT	272	may improve the responsive of the host.
	273
	274	config ATM_FORE200E_TX_RETRY
	275	int "Maximum number of tx retries"
e92481f9	276	depends on ATM_FORE200E
1da177e4	277	default "16"
a7f7f624	278	help
1da177e4 LT	279	Specifies the number of times the driver attempts to transmit
	280	a message before giving up, if the transmit queue of the ATM card
	281	is transiently saturated.
	282
	283	Saturation of the transmit queue may occur only under extreme
	284	conditions, e.g. when a fast host continuously submits very small
	285	frames (<64 bytes) or raw AAL0 cells (48 bytes) to the ATM adapter.
	286
	287	Note that under common conditions, it is unlikely that you encounter
	288	a saturation of the transmit queue, so the retry mechanism never
	289	comes into play.
	290
	291	config ATM_FORE200E_DEBUG
	292	int "Debugging level (0-3)"
e92481f9	293	depends on ATM_FORE200E
1da177e4 LT	294	default "0"
	295	help
	296	Specifies the level of debugging messages issued by the driver.
	297	The verbosity of the driver increases with the value of this
	298	parameter.
	299
	300	When active, these messages can have a significant impact on
	301	the performances of the driver, and the size of your syslog files!
	302	Keep the debugging level to 0 during normal operations.
	303
1da177e4 LT	304	config ATM_HE
1da177e4 LT	305	tristate "ForeRunner HE Series"
4151ce31	306	depends on PCI
1da177e4 LT	307	help
	308	This is a driver for the Marconi ForeRunner HE-series ATM adapter
	309	cards. It simultaneously supports the 155 and 622 versions.
	310
	311	config ATM_HE_USE_SUNI
	312	bool "Use S/UNI PHY driver"
	313	depends on ATM_HE
	314	help
	315	Support for the S/UNI-Ultra and S/UNI-622 found in the ForeRunner
	316	HE cards. This driver provides carrier detection some statistics.
	317
9c54004e DW	318	config ATM_SOLOS
	319	tristate "Solos ADSL2+ PCI Multiport card driver"
	320	depends on PCI
e1bc7eed	321	select FW_LOADER
9c54004e DW	322	help
	323	Support for the Solos multiport ADSL2+ card.
	324
4151ce31	325	endif # ATM