projects / linux.git / blame
| Commit | Line | Data |
|---|---|---|
| 1da177e4 LT |
1 | /* TERMS AND CONDITIONS OF USE |
| 2 | * | |
| 3 | * Redistribution and use in source form, with or without modification, are | |
| 4 | * permitted provided that redistributions of source code must retain the | |
| 5 | * above copyright notice, this list of conditions and the following disclaimer. | |
| 6 | * | |
| 7 | * This software is provided `as is' by Adaptec and | |
| 8 | * any express or implied warranties, including, but not limited to, the | |
| 9 | * implied warranties of merchantability and fitness for a particular purpose, | |
| 10 | * are disclaimed. In no event shall Adaptec be | |
| 11 | * liable for any direct, indirect, incidental, special, exemplary or | |
| 12 | * consequential damages (including, but not limited to, procurement of | |
| 13 | * substitute goods or services; loss of use, data, or profits; or business | |
| 14 | * interruptions) however caused and on any theory of liability, whether in | |
| 15 | * contract, strict liability, or tort (including negligence or otherwise) | |
| 16 | * arising in any way out of the use of this driver software, even if advised | |
| 17 | * of the possibility of such damage. | |
| 18 | * | |
| 19 | **************************************************************** | |
| 20 | * This driver supports the Adaptec I2O RAID and DPT SmartRAID V I2O boards. | |
| 21 | * | |
| 22 | * CREDITS: | |
| 23 | * The original linux driver was ported to Linux by Karen White while at | |
| 24 | * Dell Computer. It was ported from Bob Pasteur's (of DPT) original | |
| 25 | * non-Linux driver. Mark Salyzyn and Bob Pasteur consulted on the original | |
| 26 | * driver. | |
| 27 | * | |
| 28 | * 2.0 version of the driver by Deanna Bonds and Mark Salyzyn. | |
| 29 | * | |
| 30 | * HISTORY: | |
| 31 | * The driver was originally ported to linux version 2.0.34 | |
| 32 | * | |
| 33 | * V2.0 Rewrite of driver. Re-architectured based on i2o subsystem. | |
| 34 | * This was the first full GPL version since the last version used | |
| 35 | * i2osig headers which were not GPL. Developer Testing version. | |
| 36 | * V2.1 Internal testing | |
| 37 | * V2.2 First released version | |
| 38 | * | |
| 39 | * V2.3 | |
| 40 | * Changes: | |
| 41 | * Added Raptor Support | |
| 42 | * Fixed bug causing system to hang under extreme load with | |
| 43 | * management utilities running (removed GFP_DMA from kmalloc flags) | |
| 44 | * | |
| 45 | * | |
| 46 | * V2.4 First version ready to be submitted to be embedded in the kernel | |
| 47 | * Changes: | |
| 48 | * Implemented suggestions from Alan Cox | |
| 49 | * Added calculation of resid for sg layer | |
| 50 | * Better error handling | |
| 6c28f2c0 | 51 | * Added checking underflow conditions |
| 1da177e4 LT |
52 | * Added DATAPROTECT checking |
| 53 | * Changed error return codes | |
| 54 | * Fixed pointer bug in bus reset routine | |
| 55 | * Enabled hba reset from ioctls (allows a FW flash to reboot and use the new | |
| 56 | * FW without having to reboot) | |
| 57 | * Changed proc output | |
| 58 | * | |
| 59 | * TODO: | |
| 60 | * Add 64 bit Scatter Gather when compiled on 64 bit architectures | |
| 61 | * Add sparse lun scanning | |
| 62 | * Add code that checks if a device that had been taken offline is | |
| 63 | * now online (at the FW level) when test unit ready or inquiry | |
| 64 | * command from scsi-core | |
| 65 | * Add proc read interface | |
| 66 | * busrescan command | |
| 67 | * rescan command | |
| 68 | * Add code to rescan routine that notifies scsi-core about new devices | |
| 69 | * Add support for C-PCI (hotplug stuff) | |
| 70 | * Add ioctl passthru error recovery | |
| 71 | * | |
| 72 | * NOTES: | |
| 73 | * The DPT card optimizes the order of processing commands. Consequently, | |
| 74 | * a command may take up to 6 minutes to complete after it has been sent | |
| 75 | * to the board. | |
| 76 | * | |
| 77 | * The files dpti_ioctl.h dptsig.h osd_defs.h osd_util.h sys_info.h are part of the | |
| 78 | * interface files for Adaptec's management routines. These define the structures used | |
| 79 | * in the ioctls. They are written to be portable. They are hard to read, but I need | |
| 80 | * to use them 'as is' or I can miss changes in the interface. | |
| 81 | * | |
| 82 | */ | |
| 83 |