[linux.git] / drivers / hwmon / w83l785ts.c

/*
 * w83l785ts.c - Part of lm_sensors, Linux kernel modules for hardware
 *               monitoring
 * Copyright (C) 2003-2004  Jean Delvare <[email protected]>
 *
 * Inspired from the lm83 driver. The W83L785TS-S is a sensor chip made
 * by Winbond. It reports a single external temperature with a 1 deg
 * resolution and a 3 deg accuracy. Datasheet can be obtained from
 * Winbond's website at:
 *   http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/W83L785TS-S.pdf
 *
 * Ported to Linux 2.6 by Wolfgang Ziegler <[email protected]> and Jean Delvare
 * <[email protected]>.
 *
 * Thanks to James Bolt <[email protected]> for benchmarking the read
 * error handling mechanism.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
 */

#include <linux/module.h>
#include <linux/delay.h>
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/jiffies.h>
#include <linux/i2c.h>
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
#include <linux/err.h>
#include <linux/mutex.h>

/* How many retries on register read error */
#define MAX_RETRIES	5

/*
 * Address to scan
 * Address is fully defined internally and cannot be changed.
 */

static unsigned short normal_i2c[] = { 0x2e, I2C_CLIENT_END };

/*
 * Insmod parameters
 */

I2C_CLIENT_INSMOD_1(w83l785ts);

/*
 * The W83L785TS-S registers
 * Manufacturer ID is 0x5CA3 for Winbond.
 */

#define W83L785TS_REG_MAN_ID1		0x4D
#define W83L785TS_REG_MAN_ID2		0x4C
#define W83L785TS_REG_CHIP_ID		0x4E
#define W83L785TS_REG_CONFIG		0x40
#define W83L785TS_REG_TYPE		0x52
#define W83L785TS_REG_TEMP		0x27
#define W83L785TS_REG_TEMP_OVER		0x53 /* not sure about this one */

/*
 * Conversions
 * The W83L785TS-S uses signed 8-bit values.
 */

#define TEMP_FROM_REG(val)	((val) * 1000)

/*
 * Functions declaration
 */

static int w83l785ts_attach_adapter(struct i2c_adapter *adapter);
static int w83l785ts_detect(struct i2c_adapter *adapter, int address,
	int kind);
static int w83l785ts_detach_client(struct i2c_client *client);
static u8 w83l785ts_read_value(struct i2c_client *client, u8 reg, u8 defval);
static struct w83l785ts_data *w83l785ts_update_device(struct device *dev);

/*
 * Driver data (common to all clients)
 */
 
static struct i2c_driver w83l785ts_driver = {
	.driver = {
		.name	= "w83l785ts",
	},
	.id		= I2C_DRIVERID_W83L785TS,
	.attach_adapter	= w83l785ts_attach_adapter,
	.detach_client	= w83l785ts_detach_client,
};

/*
 * Client data (each client gets its own)
 */

struct w83l785ts_data {
	struct i2c_client client;
	struct device *hwmon_dev;
	struct mutex update_lock;
	char valid; /* zero until following fields are valid */
	unsigned long last_updated; /* in jiffies */

	/* registers values */
	s8 temp[2]; /* 0: input
		       1: critical limit */
};

/*
 * Sysfs stuff
 */

static ssize_t show_temp(struct device *dev, struct device_attribute *devattr,
	char *buf)
{
	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
	struct w83l785ts_data *data = w83l785ts_update_device(dev);
	return sprintf(buf, "%d\n", TEMP_FROM_REG(data->temp[attr->index]));
}

static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_temp, NULL, 0);
static SENSOR_DEVICE_ATTR(temp1_max, S_IRUGO, show_temp, NULL, 1);

/*
 * Real code
 */

static int w83l785ts_attach_adapter(struct i2c_adapter *adapter)
{
	if (!(adapter->class & I2C_CLASS_HWMON))
		return 0;
	return i2c_probe(adapter, &addr_data, w83l785ts_detect);
}

/*
 * The following function does more than just detection. If detection
 * succeeds, it also registers the new chip.
 */
static int w83l785ts_detect(struct i2c_adapter *adapter, int address, int kind)
{
	struct i2c_client *new_client;
	struct w83l785ts_data *data;
	int err = 0;


	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
		goto exit;

	if (!(data = kzalloc(sizeof(struct w83l785ts_data), GFP_KERNEL))) {
		err = -ENOMEM;
		goto exit;
	}

	/* The common I2C client data is placed right before the
	 * W83L785TS-specific data. */
	new_client = &data->client;
	i2c_set_clientdata(new_client, data);
	new_client->addr = address;
	new_client->adapter = adapter;
	new_client->driver = &w83l785ts_driver;
	new_client->flags = 0;

	/*
	 * Now we do the remaining detection. A negative kind means that
	 * the driver was loaded with no force parameter (default), so we
	 * must both detect and identify the chip (actually there is only
	 * one possible kind of chip for now, W83L785TS-S). A zero kind means
	 * that the driver was loaded with the force parameter, the detection
	 * step shall be skipped. A positive kind means that the driver
	 * was loaded with the force parameter and a given kind of chip is
	 * requested, so both the detection and the identification steps
	 * are skipped.
	 */
	if (kind < 0) { /* detection */
		if (((w83l785ts_read_value(new_client,
		      W83L785TS_REG_CONFIG, 0) & 0x80) != 0x00)
		 || ((w83l785ts_read_value(new_client,
		      W83L785TS_REG_TYPE, 0) & 0xFC) != 0x00)) {
			dev_dbg(&adapter->dev,
				"W83L785TS-S detection failed at 0x%02x.\n",
				address);
			goto exit_free;
		}
	}

	if (kind <= 0) { /* identification */
		u16 man_id;
		u8 chip_id;

		man_id = (w83l785ts_read_value(new_client,
			 W83L785TS_REG_MAN_ID1, 0) << 8) +
			 w83l785ts_read_value(new_client,
			 W83L785TS_REG_MAN_ID2, 0);
		chip_id = w83l785ts_read_value(new_client,
			  W83L785TS_REG_CHIP_ID, 0);

		if (man_id == 0x5CA3) { /* Winbond */
			if (chip_id == 0x70) { /* W83L785TS-S */
				kind = w83l785ts;			
			}
		}
	
		if (kind <= 0) { /* identification failed */
			dev_info(&adapter->dev,
				 "Unsupported chip (man_id=0x%04X, "
				 "chip_id=0x%02X).\n", man_id, chip_id);
			goto exit_free;
		}
	}

	/* We can fill in the remaining client fields. */
	strlcpy(new_client->name, "w83l785ts", I2C_NAME_SIZE);
	data->valid = 0;
	mutex_init(&data->update_lock);

	/* Default values in case the first read fails (unlikely). */
	data->temp[1] = data->temp[0] = 0;

	/* Tell the I2C layer a new client has arrived. */
	if ((err = i2c_attach_client(new_client))) 
		goto exit_free;

	/*
	 * Initialize the W83L785TS chip
	 * Nothing yet, assume it is already started.
	 */

	err = device_create_file(&new_client->dev,
				 &sensor_dev_attr_temp1_input.dev_attr);
	if (err)
		goto exit_remove;

	err = device_create_file(&new_client->dev,
				 &sensor_dev_attr_temp1_max.dev_attr);
	if (err)
		goto exit_remove;

	/* Register sysfs hooks */
	data->hwmon_dev = hwmon_device_register(&new_client->dev);
	if (IS_ERR(data->hwmon_dev)) {
		err = PTR_ERR(data->hwmon_dev);
		goto exit_remove;
	}

	return 0;

exit_remove:
	device_remove_file(&new_client->dev,
			   &sensor_dev_attr_temp1_input.dev_attr);
	device_remove_file(&new_client->dev,
			   &sensor_dev_attr_temp1_max.dev_attr);
	i2c_detach_client(new_client);
exit_free:
	kfree(data);
exit:
	return err;
}

static int w83l785ts_detach_client(struct i2c_client *client)
{
	struct w83l785ts_data *data = i2c_get_clientdata(client);
	int err;

	hwmon_device_unregister(data->hwmon_dev);
	device_remove_file(&client->dev,
			   &sensor_dev_attr_temp1_input.dev_attr);
	device_remove_file(&client->dev,
			   &sensor_dev_attr_temp1_max.dev_attr);
	if ((err = i2c_detach_client(client)))
		return err;

	kfree(data);
	return 0;
}

static u8 w83l785ts_read_value(struct i2c_client *client, u8 reg, u8 defval)
{
	int value, i;

	/* Frequent read errors have been reported on Asus boards, so we
	 * retry on read errors. If it still fails (unlikely), return the
	 * default value requested by the caller. */
	for (i = 1; i <= MAX_RETRIES; i++) {
		value = i2c_smbus_read_byte_data(client, reg);
		if (value >= 0) {
			dev_dbg(&client->dev, "Read 0x%02x from register "
				"0x%02x.\n", value, reg);
			return value;
		}
		dev_dbg(&client->dev, "Read failed, will retry in %d.\n", i);
		msleep(i);
	}

	dev_err(&client->dev, "Couldn't read value from register 0x%02x. "
		"Please report.\n", reg);
	return defval;
}

static struct w83l785ts_data *w83l785ts_update_device(struct device *dev)
{
	struct i2c_client *client = to_i2c_client(dev);
	struct w83l785ts_data *data = i2c_get_clientdata(client);

	mutex_lock(&data->update_lock);

	if (!data->valid || time_after(jiffies, data->last_updated + HZ * 2)) {
		dev_dbg(&client->dev, "Updating w83l785ts data.\n");
		data->temp[0] = w83l785ts_read_value(client,
				W83L785TS_REG_TEMP, data->temp[0]);
		data->temp[1] = w83l785ts_read_value(client,
				W83L785TS_REG_TEMP_OVER, data->temp[1]);

		data->last_updated = jiffies;
		data->valid = 1;
	}

	mutex_unlock(&data->update_lock);

	return data;
}

static int __init sensors_w83l785ts_init(void)
{
	return i2c_add_driver(&w83l785ts_driver);
}

static void __exit sensors_w83l785ts_exit(void)
{
	i2c_del_driver(&w83l785ts_driver);
}

MODULE_AUTHOR("Jean Delvare <[email protected]>");
MODULE_DESCRIPTION("W83L785TS-S driver");
MODULE_LICENSE("GPL");

module_init(sensors_w83l785ts_init);
module_exit(sensors_w83l785ts_exit);
Commit	Line	Data
1da177e4 LT	1	/*
	2	* w83l785ts.c - Part of lm_sensors, Linux kernel modules for hardware
	3	* monitoring
	4	* Copyright (C) 2003-2004 Jean Delvare <[email protected]>
	5	*
	6	* Inspired from the lm83 driver. The W83L785TS-S is a sensor chip made
	7	* by Winbond. It reports a single external temperature with a 1 deg
	8	* resolution and a 3 deg accuracy. Datasheet can be obtained from
	9	* Winbond's website at:
	10	* http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/W83L785TS-S.pdf
	11	*
	12	* Ported to Linux 2.6 by Wolfgang Ziegler <[email protected]> and Jean Delvare
	13	* <[email protected]>.
	14	*
	15	* Thanks to James Bolt <[email protected]> for benchmarking the read
	16	* error handling mechanism.
	17	*
	18	* This program is free software; you can redistribute it and/or modify
	19	* it under the terms of the GNU General Public License as published by
	20	* the Free Software Foundation; either version 2 of the License, or
	21	* (at your option) any later version.
	22	*
	23	* This program is distributed in the hope that it will be useful,
	24	* but WITHOUT ANY WARRANTY; without even the implied warranty of
	25	* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
	26	* GNU General Public License for more details.
	27	*
	28	* You should have received a copy of the GNU General Public License
	29	* along with this program; if not, write to the Free Software
	30	* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
	31	*/
	32
1da177e4 LT	33	#include <linux/module.h>
	34	#include <linux/delay.h>
	35	#include <linux/init.h>
	36	#include <linux/slab.h>
	37	#include <linux/jiffies.h>
	38	#include <linux/i2c.h>
943b0830	39	#include <linux/hwmon.h>
709439a2	40	#include <linux/hwmon-sysfs.h>
943b0830	41	#include <linux/err.h>
9a61bf63	42	#include <linux/mutex.h>
1da177e4 LT	43
	44	/* How many retries on register read error */
	45	#define MAX_RETRIES 5
	46
	47	/*
	48	* Address to scan
	49	* Address is fully defined internally and cannot be changed.
	50	*/
	51
	52	static unsigned short normal_i2c[] = { 0x2e, I2C_CLIENT_END };
1da177e4 LT	53
	54	/*
	55	* Insmod parameters
	56	*/
	57
f4b50261	58	I2C_CLIENT_INSMOD_1(w83l785ts);
1da177e4 LT	59
	60	/*
	61	* The W83L785TS-S registers
	62	* Manufacturer ID is 0x5CA3 for Winbond.
	63	*/
	64
	65	#define W83L785TS_REG_MAN_ID1 0x4D
	66	#define W83L785TS_REG_MAN_ID2 0x4C
	67	#define W83L785TS_REG_CHIP_ID 0x4E
	68	#define W83L785TS_REG_CONFIG 0x40
	69	#define W83L785TS_REG_TYPE 0x52
	70	#define W83L785TS_REG_TEMP 0x27
	71	#define W83L785TS_REG_TEMP_OVER 0x53 /* not sure about this one */
	72
	73	/*
	74	* Conversions
	75	* The W83L785TS-S uses signed 8-bit values.
	76	*/
	77
cb929eae	78	#define TEMP_FROM_REG(val) ((val) * 1000)
1da177e4 LT	79
	80	/*
	81	* Functions declaration
	82	*/
	83
	84	static int w83l785ts_attach_adapter(struct i2c_adapter *adapter);
	85	static int w83l785ts_detect(struct i2c_adapter *adapter, int address,
	86	int kind);
	87	static int w83l785ts_detach_client(struct i2c_client *client);
	88	static u8 w83l785ts_read_value(struct i2c_client *client, u8 reg, u8 defval);
	89	static struct w83l785ts_data w83l785ts_update_device(struct device dev);
	90
	91	/*
	92	* Driver data (common to all clients)
	93	*/
	94
	95	static struct i2c_driver w83l785ts_driver = {
cdaf7934	96	.driver = {
cdaf7934 LR	97	.name = "w83l785ts",
cdaf7934 LR	98	},
1da177e4	99	.id = I2C_DRIVERID_W83L785TS,
1da177e4 LT	100	.attach_adapter = w83l785ts_attach_adapter,
	101	.detach_client = w83l785ts_detach_client,
	102	};
	103
	104	/*
	105	* Client data (each client gets its own)
	106	*/
	107
	108	struct w83l785ts_data {
	109	struct i2c_client client;
1beeffe4	110	struct device *hwmon_dev;
9a61bf63	111	struct mutex update_lock;
1da177e4 LT	112	char valid; /* zero until following fields are valid */
	113	unsigned long last_updated; /* in jiffies */
	114
	115	/* registers values */
cb929eae	116	s8 temp[2]; /* 0: input
709439a2	117	1: critical limit */
1da177e4 LT	118	};
	119
	120	/*
	121	* Sysfs stuff
	122	*/
	123
709439a2 JD	124	static ssize_t show_temp(struct device dev, struct device_attribute devattr,
709439a2 JD	125	char *buf)
1da177e4	126	{
709439a2	127	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
1da177e4	128	struct w83l785ts_data *data = w83l785ts_update_device(dev);
709439a2	129	return sprintf(buf, "%d\n", TEMP_FROM_REG(data->temp[attr->index]));
1da177e4 LT	130	}
1da177e4 LT	131
709439a2 JD	132	static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_temp, NULL, 0);
709439a2 JD	133	static SENSOR_DEVICE_ATTR(temp1_max, S_IRUGO, show_temp, NULL, 1);
1da177e4 LT	134
	135	/*
	136	* Real code
	137	*/
	138
	139	static int w83l785ts_attach_adapter(struct i2c_adapter *adapter)
	140	{
	141	if (!(adapter->class & I2C_CLASS_HWMON))
	142	return 0;
2ed2dc3c	143	return i2c_probe(adapter, &addr_data, w83l785ts_detect);
1da177e4 LT	144	}
	145
	146	/*
	147	* The following function does more than just detection. If detection
	148	* succeeds, it also registers the new chip.
	149	*/
	150	static int w83l785ts_detect(struct i2c_adapter *adapter, int address, int kind)
	151	{
	152	struct i2c_client *new_client;
	153	struct w83l785ts_data *data;
	154	int err = 0;
	155
	156
	157	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
	158	goto exit;
	159
ba9c2e8d	160	if (!(data = kzalloc(sizeof(struct w83l785ts_data), GFP_KERNEL))) {
1da177e4 LT	161	err = -ENOMEM;
	162	goto exit;
	163	}
1da177e4 LT	164
	165	/* The common I2C client data is placed right before the
	166	* W83L785TS-specific data. */
	167	new_client = &data->client;
	168	i2c_set_clientdata(new_client, data);
	169	new_client->addr = address;
	170	new_client->adapter = adapter;
	171	new_client->driver = &w83l785ts_driver;
	172	new_client->flags = 0;
	173
	174	/*
	175	* Now we do the remaining detection. A negative kind means that
	176	* the driver was loaded with no force parameter (default), so we
	177	* must both detect and identify the chip (actually there is only
	178	* one possible kind of chip for now, W83L785TS-S). A zero kind means
	179	* that the driver was loaded with the force parameter, the detection
	180	* step shall be skipped. A positive kind means that the driver
	181	* was loaded with the force parameter and a given kind of chip is
	182	* requested, so both the detection and the identification steps
	183	* are skipped.
	184	*/
	185	if (kind < 0) { /* detection */
	186	if (((w83l785ts_read_value(new_client,
	187	W83L785TS_REG_CONFIG, 0) & 0x80) != 0x00)
	188	\|\| ((w83l785ts_read_value(new_client,
	189	W83L785TS_REG_TYPE, 0) & 0xFC) != 0x00)) {
	190	dev_dbg(&adapter->dev,
	191	"W83L785TS-S detection failed at 0x%02x.\n",
	192	address);
	193	goto exit_free;
	194	}
	195	}
	196
	197	if (kind <= 0) { /* identification */
	198	u16 man_id;
	199	u8 chip_id;
	200
	201	man_id = (w83l785ts_read_value(new_client,
	202	W83L785TS_REG_MAN_ID1, 0) << 8) +
	203	w83l785ts_read_value(new_client,
	204	W83L785TS_REG_MAN_ID2, 0);
	205	chip_id = w83l785ts_read_value(new_client,
	206	W83L785TS_REG_CHIP_ID, 0);
	207
	208	if (man_id == 0x5CA3) { /* Winbond */
	209	if (chip_id == 0x70) { /* W83L785TS-S */
	210	kind = w83l785ts;
	211	}
	212	}
	213
	214	if (kind <= 0) { /* identification failed */
	215	dev_info(&adapter->dev,
	216	"Unsupported chip (man_id=0x%04X, "
	217	"chip_id=0x%02X).\n", man_id, chip_id);
	218	goto exit_free;
	219	}
	220	}
	221
	222	/* We can fill in the remaining client fields. */
	223	strlcpy(new_client->name, "w83l785ts", I2C_NAME_SIZE);
	224	data->valid = 0;
9a61bf63	225	mutex_init(&data->update_lock);
1da177e4 LT	226
1da177e4 LT	227	/* Default values in case the first read fails (unlikely). */
709439a2	228	data->temp[1] = data->temp[0] = 0;
1da177e4 LT	229
	230	/* Tell the I2C layer a new client has arrived. */
	231	if ((err = i2c_attach_client(new_client)))
	232	goto exit_free;
	233
	234	/*
	235	* Initialize the W83L785TS chip
	236	* Nothing yet, assume it is already started.
	237	*/
	238
ccc5c306 RM	239	err = device_create_file(&new_client->dev,
	240	&sensor_dev_attr_temp1_input.dev_attr);
	241	if (err)
	242	goto exit_remove;
	243
	244	err = device_create_file(&new_client->dev,
	245	&sensor_dev_attr_temp1_max.dev_attr);
	246	if (err)
	247	goto exit_remove;
	248
1da177e4	249	/* Register sysfs hooks */
1beeffe4 TJ	250	data->hwmon_dev = hwmon_device_register(&new_client->dev);
	251	if (IS_ERR(data->hwmon_dev)) {
	252	err = PTR_ERR(data->hwmon_dev);
ccc5c306	253	goto exit_remove;
943b0830 MH	254	}
943b0830 MH	255
1da177e4 LT	256	return 0;
1da177e4 LT	257
ccc5c306 RM	258	exit_remove:
	259	device_remove_file(&new_client->dev,
	260	&sensor_dev_attr_temp1_input.dev_attr);
	261	device_remove_file(&new_client->dev,
	262	&sensor_dev_attr_temp1_max.dev_attr);
943b0830	263	i2c_detach_client(new_client);
1da177e4 LT	264	exit_free:
	265	kfree(data);
	266	exit:
	267	return err;
	268	}
	269
	270	static int w83l785ts_detach_client(struct i2c_client *client)
	271	{
943b0830	272	struct w83l785ts_data *data = i2c_get_clientdata(client);
1da177e4 LT	273	int err;
1da177e4 LT	274
1beeffe4	275	hwmon_device_unregister(data->hwmon_dev);
ccc5c306 RM	276	device_remove_file(&client->dev,
	277	&sensor_dev_attr_temp1_input.dev_attr);
	278	device_remove_file(&client->dev,
	279	&sensor_dev_attr_temp1_max.dev_attr);
7bef5594	280	if ((err = i2c_detach_client(client)))
1da177e4	281	return err;
1da177e4	282
943b0830	283	kfree(data);
1da177e4 LT	284	return 0;
	285	}
	286
	287	static u8 w83l785ts_read_value(struct i2c_client *client, u8 reg, u8 defval)
	288	{
	289	int value, i;
	290
	291	/* Frequent read errors have been reported on Asus boards, so we
	292	* retry on read errors. If it still fails (unlikely), return the
	293	* default value requested by the caller. */
	294	for (i = 1; i <= MAX_RETRIES; i++) {
	295	value = i2c_smbus_read_byte_data(client, reg);
	296	if (value >= 0) {
	297	dev_dbg(&client->dev, "Read 0x%02x from register "
	298	"0x%02x.\n", value, reg);
	299	return value;
	300	}
	301	dev_dbg(&client->dev, "Read failed, will retry in %d.\n", i);
	302	msleep(i);
	303	}
	304
	305	dev_err(&client->dev, "Couldn't read value from register 0x%02x. "
	306	"Please report.\n", reg);
	307	return defval;
	308	}
	309
	310	static struct w83l785ts_data w83l785ts_update_device(struct device dev)
	311	{
	312	struct i2c_client *client = to_i2c_client(dev);
	313	struct w83l785ts_data *data = i2c_get_clientdata(client);
	314
9a61bf63	315	mutex_lock(&data->update_lock);
1da177e4 LT	316
	317	if (!data->valid \|\| time_after(jiffies, data->last_updated + HZ * 2)) {
	318	dev_dbg(&client->dev, "Updating w83l785ts data.\n");
709439a2 JD	319	data->temp[0] = w83l785ts_read_value(client,
	320	W83L785TS_REG_TEMP, data->temp[0]);
	321	data->temp[1] = w83l785ts_read_value(client,
	322	W83L785TS_REG_TEMP_OVER, data->temp[1]);
1da177e4 LT	323
	324	data->last_updated = jiffies;
	325	data->valid = 1;
	326	}
	327
9a61bf63	328	mutex_unlock(&data->update_lock);
1da177e4 LT	329
	330	return data;
	331	}
	332
	333	static int __init sensors_w83l785ts_init(void)
	334	{
	335	return i2c_add_driver(&w83l785ts_driver);
	336	}
	337
	338	static void __exit sensors_w83l785ts_exit(void)
	339	{
	340	i2c_del_driver(&w83l785ts_driver);
	341	}
	342
	343	MODULE_AUTHOR("Jean Delvare <[email protected]>");
	344	MODULE_DESCRIPTION("W83L785TS-S driver");
	345	MODULE_LICENSE("GPL");
	346
	347	module_init(sensors_w83l785ts_init);
	348	module_exit(sensors_w83l785ts_exit);