[linux.git] / drivers / serial / sunzilog.h

#ifndef _SUNZILOG_H
#define _SUNZILOG_H

struct zilog_channel {
	volatile unsigned char control;
	volatile unsigned char __pad1;
	volatile unsigned char data;
	volatile unsigned char __pad2;
};

struct zilog_layout {
	struct zilog_channel channelB;
	struct zilog_channel channelA;
};

#define	NUM_ZSREGS	17
#define	R7p		16 /* Written as R7 with P15 bit 0 set */

/* Conversion routines to/from brg time constants from/to bits
 * per second.
 */
#define BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))
#define BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)

/* The Zilog register set */

#define	FLAG	0x7e

/* Write Register 0 */
#define	R0	0		/* Register selects */
#define	R1	1
#define	R2	2
#define	R3	3
#define	R4	4
#define	R5	5
#define	R6	6
#define	R7	7
#define	R8	8
#define	R9	9
#define	R10	10
#define	R11	11
#define	R12	12
#define	R13	13
#define	R14	14
#define	R15	15

#define	NULLCODE	0	/* Null Code */
#define	POINT_HIGH	0x8	/* Select upper half of registers */
#define	RES_EXT_INT	0x10	/* Reset Ext. Status Interrupts */
#define	SEND_ABORT	0x18	/* HDLC Abort */
#define	RES_RxINT_FC	0x20	/* Reset RxINT on First Character */
#define	RES_Tx_P	0x28	/* Reset TxINT Pending */
#define	ERR_RES		0x30	/* Error Reset */
#define	RES_H_IUS	0x38	/* Reset highest IUS */

#define	RES_Rx_CRC	0x40	/* Reset Rx CRC Checker */
#define	RES_Tx_CRC	0x80	/* Reset Tx CRC Checker */
#define	RES_EOM_L	0xC0	/* Reset EOM latch */

/* Write Register 1 */

#define	EXT_INT_ENAB	0x1	/* Ext Int Enable */
#define	TxINT_ENAB	0x2	/* Tx Int Enable */
#define	PAR_SPEC	0x4	/* Parity is special condition */

#define	RxINT_DISAB	0	/* Rx Int Disable */
#define	RxINT_FCERR	0x8	/* Rx Int on First Character Only or Error */
#define	INT_ALL_Rx	0x10	/* Int on all Rx Characters or error */
#define	INT_ERR_Rx	0x18	/* Int on error only */
#define RxINT_MASK	0x18

#define	WT_RDY_RT	0x20	/* Wait/Ready on R/T */
#define	WT_FN_RDYFN	0x40	/* Wait/FN/Ready FN */
#define	WT_RDY_ENAB	0x80	/* Wait/Ready Enable */

/* Write Register #2 (Interrupt Vector) */

/* Write Register 3 */

#define	RxENAB  	0x1	/* Rx Enable */
#define	SYNC_L_INH	0x2	/* Sync Character Load Inhibit */
#define	ADD_SM		0x4	/* Address Search Mode (SDLC) */
#define	RxCRC_ENAB	0x8	/* Rx CRC Enable */
#define	ENT_HM		0x10	/* Enter Hunt Mode */
#define	AUTO_ENAB	0x20	/* Auto Enables */
#define	Rx5		0x0	/* Rx 5 Bits/Character */
#define	Rx7		0x40	/* Rx 7 Bits/Character */
#define	Rx6		0x80	/* Rx 6 Bits/Character */
#define	Rx8		0xc0	/* Rx 8 Bits/Character */
#define RxN_MASK	0xc0

/* Write Register 4 */

#define	PAR_ENAB	0x1	/* Parity Enable */
#define	PAR_EVEN	0x2	/* Parity Even/Odd* */

#define	SYNC_ENAB	0	/* Sync Modes Enable */
#define	SB1		0x4	/* 1 stop bit/char */
#define	SB15		0x8	/* 1.5 stop bits/char */
#define	SB2		0xc	/* 2 stop bits/char */

#define	MONSYNC		0	/* 8 Bit Sync character */
#define	BISYNC		0x10	/* 16 bit sync character */
#define	SDLC		0x20	/* SDLC Mode (01111110 Sync Flag) */
#define	EXTSYNC		0x30	/* External Sync Mode */

#define	X1CLK		0x0	/* x1 clock mode */
#define	X16CLK		0x40	/* x16 clock mode */
#define	X32CLK		0x80	/* x32 clock mode */
#define	X64CLK		0xC0	/* x64 clock mode */
#define XCLK_MASK	0xC0

/* Write Register 5 */

#define	TxCRC_ENAB	0x1	/* Tx CRC Enable */
#define	RTS		0x2	/* RTS */
#define	SDLC_CRC	0x4	/* SDLC/CRC-16 */
#define	TxENAB		0x8	/* Tx Enable */
#define	SND_BRK		0x10	/* Send Break */
#define	Tx5		0x0	/* Tx 5 bits (or less)/character */
#define	Tx7		0x20	/* Tx 7 bits/character */
#define	Tx6		0x40	/* Tx 6 bits/character */
#define	Tx8		0x60	/* Tx 8 bits/character */
#define TxN_MASK	0x60
#define	DTR		0x80	/* DTR */

/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */

/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */

/* Write Register 7' (ESCC Only) */
#define	AUTO_TxFLAG	1	/* Automatic Tx SDLC Flag */
#define	AUTO_EOM_RST	2	/* Automatic EOM Reset */
#define	AUTOnRTS	4	/* Automatic /RTS pin deactivation */
#define	RxFIFO_LVL	8	/* Receive FIFO interrupt level */
#define	nDTRnREQ	0x10	/* /DTR/REQ timing */
#define	TxFIFO_LVL	0x20	/* Transmit FIFO interrupt level */
#define	EXT_RD_EN	0x40	/* Extended read register enable */

/* Write Register 8 (transmit buffer) */

/* Write Register 9 (Master interrupt control) */
#define	VIS	1	/* Vector Includes Status */
#define	NV	2	/* No Vector */
#define	DLC	4	/* Disable Lower Chain */
#define	MIE	8	/* Master Interrupt Enable */
#define	STATHI	0x10	/* Status high */
#define	SWIACK  0x20    /* Software Interrupt Ack (not on NMOS) */
#define	NORESET	0	/* No reset on write to R9 */
#define	CHRB	0x40	/* Reset channel B */
#define	CHRA	0x80	/* Reset channel A */
#define	FHWRES	0xc0	/* Force hardware reset */

/* Write Register 10 (misc control bits) */
#define	BIT6	1	/* 6 bit/8bit sync */
#define	LOOPMODE 2	/* SDLC Loop mode */
#define	ABUNDER	4	/* Abort/flag on SDLC xmit underrun */
#define	MARKIDLE 8	/* Mark/flag on idle */
#define	GAOP	0x10	/* Go active on poll */
#define	NRZ	0	/* NRZ mode */
#define	NRZI	0x20	/* NRZI mode */
#define	FM1	0x40	/* FM1 (transition = 1) */
#define	FM0	0x60	/* FM0 (transition = 0) */
#define	CRCPS	0x80	/* CRC Preset I/O */

/* Write Register 11 (Clock Mode control) */
#define	TRxCXT	0	/* TRxC = Xtal output */
#define	TRxCTC	1	/* TRxC = Transmit clock */
#define	TRxCBR	2	/* TRxC = BR Generator Output */
#define	TRxCDP	3	/* TRxC = DPLL output */
#define	TRxCOI	4	/* TRxC O/I */
#define	TCRTxCP	0	/* Transmit clock = RTxC pin */
#define	TCTRxCP	8	/* Transmit clock = TRxC pin */
#define	TCBR	0x10	/* Transmit clock = BR Generator output */
#define	TCDPLL	0x18	/* Transmit clock = DPLL output */
#define	RCRTxCP	0	/* Receive clock = RTxC pin */
#define	RCTRxCP	0x20	/* Receive clock = TRxC pin */
#define	RCBR	0x40	/* Receive clock = BR Generator output */
#define	RCDPLL	0x60	/* Receive clock = DPLL output */
#define	RTxCX	0x80	/* RTxC Xtal/No Xtal */

/* Write Register 12 (lower byte of baud rate generator time constant) */

/* Write Register 13 (upper byte of baud rate generator time constant) */

/* Write Register 14 (Misc control bits) */
#define	BRENAB 	1	/* Baud rate generator enable */
#define	BRSRC	2	/* Baud rate generator source */
#define	DTRREQ	4	/* DTR/Request function */
#define	AUTOECHO 8	/* Auto Echo */
#define	LOOPBAK	0x10	/* Local loopback */
#define	SEARCH	0x20	/* Enter search mode */
#define	RMC	0x40	/* Reset missing clock */
#define	DISDPLL	0x60	/* Disable DPLL */
#define	SSBR	0x80	/* Set DPLL source = BR generator */
#define	SSRTxC	0xa0	/* Set DPLL source = RTxC */
#define	SFMM	0xc0	/* Set FM mode */
#define	SNRZI	0xe0	/* Set NRZI mode */

/* Write Register 15 (external/status interrupt control) */
#define	WR7pEN	1	/* WR7' Enable (ESCC only) */
#define	ZCIE	2	/* Zero count IE */
#define	FIFOEN	4	/* FIFO Enable (ESCC only) */
#define	DCDIE	8	/* DCD IE */
#define	SYNCIE	0x10	/* Sync/hunt IE */
#define	CTSIE	0x20	/* CTS IE */
#define	TxUIE	0x40	/* Tx Underrun/EOM IE */
#define	BRKIE	0x80	/* Break/Abort IE */


/* Read Register 0 */
#define	Rx_CH_AV	0x1	/* Rx Character Available */
#define	ZCOUNT		0x2	/* Zero count */
#define	Tx_BUF_EMP	0x4	/* Tx Buffer empty */
#define	DCD		0x8	/* DCD */
#define	SYNC		0x10	/* Sync/hunt */
#define	CTS		0x20	/* CTS */
#define	TxEOM		0x40	/* Tx underrun */
#define	BRK_ABRT	0x80	/* Break/Abort */

/* Read Register 1 */
#define	ALL_SNT		0x1	/* All sent */
/* Residue Data for 8 Rx bits/char programmed */
#define	RES3		0x8	/* 0/3 */
#define	RES4		0x4	/* 0/4 */
#define	RES5		0xc	/* 0/5 */
#define	RES6		0x2	/* 0/6 */
#define	RES7		0xa	/* 0/7 */
#define	RES8		0x6	/* 0/8 */
#define	RES18		0xe	/* 1/8 */
#define	RES28		0x0	/* 2/8 */
/* Special Rx Condition Interrupts */
#define	PAR_ERR		0x10	/* Parity error */
#define	Rx_OVR		0x20	/* Rx Overrun Error */
#define	CRC_ERR		0x40	/* CRC/Framing Error */
#define	END_FR		0x80	/* End of Frame (SDLC) */

/* Read Register 2 (channel b only) - Interrupt vector */
#define CHB_Tx_EMPTY	0x00
#define CHB_EXT_STAT	0x02
#define CHB_Rx_AVAIL	0x04
#define CHB_SPECIAL	0x06
#define CHA_Tx_EMPTY	0x08
#define CHA_EXT_STAT	0x0a
#define CHA_Rx_AVAIL	0x0c
#define CHA_SPECIAL	0x0e
#define STATUS_MASK	0x0e

/* Read Register 3 (interrupt pending register) ch a only */
#define	CHBEXT	0x1		/* Channel B Ext/Stat IP */
#define	CHBTxIP	0x2		/* Channel B Tx IP */
#define	CHBRxIP	0x4		/* Channel B Rx IP */
#define	CHAEXT	0x8		/* Channel A Ext/Stat IP */
#define	CHATxIP	0x10		/* Channel A Tx IP */
#define	CHARxIP	0x20		/* Channel A Rx IP */

/* Read Register 6 (LSB frame byte count [Not on NMOS]) */

/* Read Register 7 (MSB frame byte count and FIFO status [Not on NMOS]) */

/* Read Register 8 (receive data register) */

/* Read Register 10  (misc status bits) */
#define	ONLOOP	2		/* On loop */
#define	LOOPSEND 0x10		/* Loop sending */
#define	CLK2MIS	0x40		/* Two clocks missing */
#define	CLK1MIS	0x80		/* One clock missing */

/* Read Register 12 (lower byte of baud rate generator constant) */

/* Read Register 13 (upper byte of baud rate generator constant) */

/* Read Register 15 (value of WR 15) */

/* Misc macros */
#define ZS_CLEARERR(channel)    do { sbus_writeb(ERR_RES, &channel->control); \
				     udelay(5); } while(0)

#define ZS_CLEARSTAT(channel)   do { sbus_writeb(RES_EXT_INT, &channel->control); \
				     udelay(5); } while(0)

#define ZS_CLEARFIFO(channel)   do { sbus_readb(&channel->data); \
				     udelay(2); \
				     sbus_readb(&channel->data); \
				     udelay(2); \
				     sbus_readb(&channel->data); \
				     udelay(2); } while(0)

#endif /* _SUNZILOG_H */
Commit	Line	Data
1da177e4 LT	1	#ifndef _SUNZILOG_H
	2	#define _SUNZILOG_H
	3
	4	struct zilog_channel {
	5	volatile unsigned char control;
	6	volatile unsigned char __pad1;
	7	volatile unsigned char data;
	8	volatile unsigned char __pad2;
	9	};
	10
	11	struct zilog_layout {
	12	struct zilog_channel channelB;
	13	struct zilog_channel channelA;
	14	};
	15
7cc5c855 MF	16	#define NUM_ZSREGS 17
7cc5c855 MF	17	#define R7p 16 /* Written as R7 with P15 bit 0 set */
1da177e4 LT	18
	19	/* Conversion routines to/from brg time constants from/to bits
	20	* per second.
	21	*/
	22	#define BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))
	23	#define BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)
	24
	25	/* The Zilog register set */
	26
	27	#define FLAG 0x7e
	28
	29	/* Write Register 0 */
	30	#define R0 0 /* Register selects */
	31	#define R1 1
	32	#define R2 2
	33	#define R3 3
	34	#define R4 4
	35	#define R5 5
	36	#define R6 6
	37	#define R7 7
	38	#define R8 8
	39	#define R9 9
	40	#define R10 10
	41	#define R11 11
	42	#define R12 12
	43	#define R13 13
	44	#define R14 14
	45	#define R15 15
	46
	47	#define NULLCODE 0 /* Null Code */
	48	#define POINT_HIGH 0x8 /* Select upper half of registers */
	49	#define RES_EXT_INT 0x10 /* Reset Ext. Status Interrupts */
	50	#define SEND_ABORT 0x18 /* HDLC Abort */
	51	#define RES_RxINT_FC 0x20 /* Reset RxINT on First Character */
	52	#define RES_Tx_P 0x28 /* Reset TxINT Pending */
	53	#define ERR_RES 0x30 /* Error Reset */
	54	#define RES_H_IUS 0x38 /* Reset highest IUS */
	55
	56	#define RES_Rx_CRC 0x40 /* Reset Rx CRC Checker */
	57	#define RES_Tx_CRC 0x80 /* Reset Tx CRC Checker */
	58	#define RES_EOM_L 0xC0 /* Reset EOM latch */
	59
	60	/* Write Register 1 */
	61
	62	#define EXT_INT_ENAB 0x1 /* Ext Int Enable */
	63	#define TxINT_ENAB 0x2 /* Tx Int Enable */
	64	#define PAR_SPEC 0x4 /* Parity is special condition */
	65
	66	#define RxINT_DISAB 0 /* Rx Int Disable */
	67	#define RxINT_FCERR 0x8 /* Rx Int on First Character Only or Error */
	68	#define INT_ALL_Rx 0x10 /* Int on all Rx Characters or error */
	69	#define INT_ERR_Rx 0x18 /* Int on error only */
	70	#define RxINT_MASK 0x18
	71
	72	#define WT_RDY_RT 0x20 /* Wait/Ready on R/T */
	73	#define WT_FN_RDYFN 0x40 /* Wait/FN/Ready FN */
	74	#define WT_RDY_ENAB 0x80 /* Wait/Ready Enable */
	75
	76	/* Write Register #2 (Interrupt Vector) */
	77
	78	/* Write Register 3 */
	79
	80	#define RxENAB 0x1 /* Rx Enable */
	81	#define SYNC_L_INH 0x2 /* Sync Character Load Inhibit */
82	#define ADD_SM 0x4 /* Address Search Mode (SDLC) */
83	#define RxCRC_ENAB 0x8 /* Rx CRC Enable */
84	#define ENT_HM 0x10 /* Enter Hunt Mode */
85	#define AUTO_ENAB 0x20 /* Auto Enables */
86	#define Rx5 0x0 /* Rx 5 Bits/Character */
87	#define Rx7 0x40 /* Rx 7 Bits/Character */
88	#define Rx6 0x80 /* Rx 6 Bits/Character */
89	#define Rx8 0xc0 /* Rx 8 Bits/Character */
90	#define RxN_MASK 0xc0
91
92	/* Write Register 4 */
93
94	#define PAR_ENAB 0x1 /* Parity Enable */
95	#define PAR_EVEN 0x2 /* Parity Even/Odd* */
96
97	#define SYNC_ENAB 0 /* Sync Modes Enable */
98	#define SB1 0x4 /* 1 stop bit/char */
99	#define SB15 0x8 /* 1.5 stop bits/char */
100	#define SB2 0xc /* 2 stop bits/char */
101
102	#define MONSYNC 0 /* 8 Bit Sync character */
103	#define BISYNC 0x10 /* 16 bit sync character */
104	#define SDLC 0x20 /* SDLC Mode (01111110 Sync Flag) */
105	#define EXTSYNC 0x30 /* External Sync Mode */
106
107	#define X1CLK 0x0 /* x1 clock mode */
108	#define X16CLK 0x40 /* x16 clock mode */
109	#define X32CLK 0x80 /* x32 clock mode */
110	#define X64CLK 0xC0 /* x64 clock mode */
111	#define XCLK_MASK 0xC0
112
113	/* Write Register 5 */
114
115	#define TxCRC_ENAB 0x1 /* Tx CRC Enable */
116	#define RTS 0x2 /* RTS */
117	#define SDLC_CRC 0x4 /* SDLC/CRC-16 */
118	#define TxENAB 0x8 /* Tx Enable */
119	#define SND_BRK 0x10 /* Send Break */
120	#define Tx5 0x0 /* Tx 5 bits (or less)/character */
121	#define Tx7 0x20 /* Tx 7 bits/character */
122	#define Tx6 0x40 /* Tx 6 bits/character */
123	#define Tx8 0x60 /* Tx 8 bits/character */
124	#define TxN_MASK 0x60
125	#define DTR 0x80 /* DTR */
126
127	/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */
128
129	/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
130
7cc5c855 MF	131	/* Write Register 7' (ESCC Only) */
	132	#define AUTO_TxFLAG 1 /* Automatic Tx SDLC Flag */
	133	#define AUTO_EOM_RST 2 /* Automatic EOM Reset */
	134	#define AUTOnRTS 4 /* Automatic /RTS pin deactivation */
	135	#define RxFIFO_LVL 8 /* Receive FIFO interrupt level */
	136	#define nDTRnREQ 0x10 /* /DTR/REQ timing */
	137	#define TxFIFO_LVL 0x20 /* Transmit FIFO interrupt level */
	138	#define EXT_RD_EN 0x40 /* Extended read register enable */
	139
1da177e4 LT	140	/* Write Register 8 (transmit buffer) */
	141
	142	/* Write Register 9 (Master interrupt control) */
	143	#define VIS 1 /* Vector Includes Status */
	144	#define NV 2 /* No Vector */
	145	#define DLC 4 /* Disable Lower Chain */
	146	#define MIE 8 /* Master Interrupt Enable */
	147	#define STATHI 0x10 /* Status high */
7cc5c855	148	#define SWIACK 0x20 /* Software Interrupt Ack (not on NMOS) */
1da177e4 LT	149	#define NORESET 0 /* No reset on write to R9 */
	150	#define CHRB 0x40 /* Reset channel B */
	151	#define CHRA 0x80 /* Reset channel A */
	152	#define FHWRES 0xc0 /* Force hardware reset */
	153
	154	/* Write Register 10 (misc control bits) */
	155	#define BIT6 1 /* 6 bit/8bit sync */
	156	#define LOOPMODE 2 /* SDLC Loop mode */
	157	#define ABUNDER 4 /* Abort/flag on SDLC xmit underrun */
	158	#define MARKIDLE 8 /* Mark/flag on idle */
	159	#define GAOP 0x10 /* Go active on poll */
	160	#define NRZ 0 /* NRZ mode */
	161	#define NRZI 0x20 /* NRZI mode */
	162	#define FM1 0x40 /* FM1 (transition = 1) */
	163	#define FM0 0x60 /* FM0 (transition = 0) */
	164	#define CRCPS 0x80 /* CRC Preset I/O */
	165
	166	/* Write Register 11 (Clock Mode control) */
	167	#define TRxCXT 0 /* TRxC = Xtal output */
	168	#define TRxCTC 1 /* TRxC = Transmit clock */
	169	#define TRxCBR 2 /* TRxC = BR Generator Output */
	170	#define TRxCDP 3 /* TRxC = DPLL output */
	171	#define TRxCOI 4 /* TRxC O/I */
	172	#define TCRTxCP 0 /* Transmit clock = RTxC pin */
	173	#define TCTRxCP 8 /* Transmit clock = TRxC pin */
	174	#define TCBR 0x10 /* Transmit clock = BR Generator output */
	175	#define TCDPLL 0x18 /* Transmit clock = DPLL output */
	176	#define RCRTxCP 0 /* Receive clock = RTxC pin */
	177	#define RCTRxCP 0x20 /* Receive clock = TRxC pin */
	178	#define RCBR 0x40 /* Receive clock = BR Generator output */
	179	#define RCDPLL 0x60 /* Receive clock = DPLL output */
	180	#define RTxCX 0x80 /* RTxC Xtal/No Xtal */
	181
	182	/* Write Register 12 (lower byte of baud rate generator time constant) */
	183
	184	/* Write Register 13 (upper byte of baud rate generator time constant) */
	185
	186	/* Write Register 14 (Misc control bits) */
	187	#define BRENAB 1 /* Baud rate generator enable */
	188	#define BRSRC 2 /* Baud rate generator source */
	189	#define DTRREQ 4 /* DTR/Request function */
	190	#define AUTOECHO 8 /* Auto Echo */
	191	#define LOOPBAK 0x10 /* Local loopback */
	192	#define SEARCH 0x20 /* Enter search mode */
	193	#define RMC 0x40 /* Reset missing clock */
	194	#define DISDPLL 0x60 /* Disable DPLL */
	195	#define SSBR 0x80 /* Set DPLL source = BR generator */
	196	#define SSRTxC 0xa0 /* Set DPLL source = RTxC */
	197	#define SFMM 0xc0 /* Set FM mode */
	198	#define SNRZI 0xe0 /* Set NRZI mode */
	199
	200	/* Write Register 15 (external/status interrupt control) */
7cc5c855	201	#define WR7pEN 1 /* WR7' Enable (ESCC only) */
1da177e4	202	#define ZCIE 2 /* Zero count IE */
7cc5c855	203	#define FIFOEN 4 /* FIFO Enable (ESCC only) */
1da177e4 LT	204	#define DCDIE 8 /* DCD IE */
	205	#define SYNCIE 0x10 /* Sync/hunt IE */
	206	#define CTSIE 0x20 /* CTS IE */
	207	#define TxUIE 0x40 /* Tx Underrun/EOM IE */
	208	#define BRKIE 0x80 /* Break/Abort IE */
	209
	210
	211	/* Read Register 0 */
	212	#define Rx_CH_AV 0x1 /* Rx Character Available */
	213	#define ZCOUNT 0x2 /* Zero count */
	214	#define Tx_BUF_EMP 0x4 /* Tx Buffer empty */
	215	#define DCD 0x8 /* DCD */
	216	#define SYNC 0x10 /* Sync/hunt */
	217	#define CTS 0x20 /* CTS */
	218	#define TxEOM 0x40 /* Tx underrun */
	219	#define BRK_ABRT 0x80 /* Break/Abort */
	220
	221	/* Read Register 1 */
	222	#define ALL_SNT 0x1 /* All sent */
	223	/* Residue Data for 8 Rx bits/char programmed */
	224	#define RES3 0x8 /* 0/3 */
	225	#define RES4 0x4 /* 0/4 */
	226	#define RES5 0xc /* 0/5 */
	227	#define RES6 0x2 /* 0/6 */
	228	#define RES7 0xa /* 0/7 */
	229	#define RES8 0x6 /* 0/8 */
	230	#define RES18 0xe /* 1/8 */
	231	#define RES28 0x0 /* 2/8 */
	232	/* Special Rx Condition Interrupts */
	233	#define PAR_ERR 0x10 /* Parity error */
	234	#define Rx_OVR 0x20 /* Rx Overrun Error */
	235	#define CRC_ERR 0x40 /* CRC/Framing Error */
	236	#define END_FR 0x80 /* End of Frame (SDLC) */
	237
	238	/* Read Register 2 (channel b only) - Interrupt vector */
	239	#define CHB_Tx_EMPTY 0x00
	240	#define CHB_EXT_STAT 0x02
	241	#define CHB_Rx_AVAIL 0x04
	242	#define CHB_SPECIAL 0x06
	243	#define CHA_Tx_EMPTY 0x08
	244	#define CHA_EXT_STAT 0x0a
	245	#define CHA_Rx_AVAIL 0x0c
	246	#define CHA_SPECIAL 0x0e
	247	#define STATUS_MASK 0x0e
	248
	249	/* Read Register 3 (interrupt pending register) ch a only */
	250	#define CHBEXT 0x1 /* Channel B Ext/Stat IP */
	251	#define CHBTxIP 0x2 /* Channel B Tx IP */
	252	#define CHBRxIP 0x4 /* Channel B Rx IP */
	253	#define CHAEXT 0x8 /* Channel A Ext/Stat IP */
	254	#define CHATxIP 0x10 /* Channel A Tx IP */
	255	#define CHARxIP 0x20 /* Channel A Rx IP */
	256
7cc5c855 MF	257	/* Read Register 6 (LSB frame byte count [Not on NMOS]) */
	258
	259	/* Read Register 7 (MSB frame byte count and FIFO status [Not on NMOS]) */
	260
1da177e4 LT	261	/* Read Register 8 (receive data register) */
	262
	263	/* Read Register 10 (misc status bits) */
	264	#define ONLOOP 2 /* On loop */
	265	#define LOOPSEND 0x10 /* Loop sending */
	266	#define CLK2MIS 0x40 /* Two clocks missing */
	267	#define CLK1MIS 0x80 /* One clock missing */
	268
	269	/* Read Register 12 (lower byte of baud rate generator constant) */
	270
	271	/* Read Register 13 (upper byte of baud rate generator constant) */
	272
	273	/* Read Register 15 (value of WR 15) */
	274
	275	/* Misc macros */
	276	#define ZS_CLEARERR(channel) do { sbus_writeb(ERR_RES, &channel->control); \
	277	udelay(5); } while(0)
	278
	279	#define ZS_CLEARSTAT(channel) do { sbus_writeb(RES_EXT_INT, &channel->control); \
	280	udelay(5); } while(0)
	281
	282	#define ZS_CLEARFIFO(channel) do { sbus_readb(&channel->data); \
	283	udelay(2); \
	284	sbus_readb(&channel->data); \
	285	udelay(2); \
	286	sbus_readb(&channel->data); \
	287	udelay(2); } while(0)
	288
	289	#endif /* _SUNZILOG_H */