--- /dev/null
+/*
+ * Copyright 2018-2020 NXP
+ * All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#ifndef __FLEXSPI_NOR_CONFIG__
+#define __FLEXSPI_NOR_CONFIG__
+
+#include <stdio.h>
+#include <stdint.h>
+#include <stdbool.h>
+
+/* FLEXSPI memory config block related defintions */
+#define FLEXSPI_CFG_BLK_TAG (0x42464346UL) // ascii "FCFB" Big Endian
+#define FLEXSPI_CFG_BLK_VERSION (0x56010400UL) // V1.4.0
+#define FLEXSPI_CFG_BLK_SIZE (512)
+
+/* FLEXSPI Feature related definitions */
+#define FLEXSPI_FEATURE_HAS_PARALLEL_MODE 1
+
+/* Lookup table related defintions */
+#define CMD_INDEX_READ 0
+#define CMD_INDEX_READSTATUS 1
+#define CMD_INDEX_WRITEENABLE 2
+#define CMD_INDEX_WRITE 4
+
+#define CMD_LUT_SEQ_IDX_READ 0
+#define CMD_LUT_SEQ_IDX_READSTATUS 1
+#define CMD_LUT_SEQ_IDX_WRITEENABLE 3
+#define CMD_LUT_SEQ_IDX_WRITE 9
+
+#define CMD_SDR 0x01
+#define CMD_DDR 0x21
+#define RADDR_SDR 0x02
+#define RADDR_DDR 0x22
+#define CADDR_SDR 0x03
+#define CADDR_DDR 0x23
+#define MODE1_SDR 0x04
+#define MODE1_DDR 0x24
+#define MODE2_SDR 0x05
+#define MODE2_DDR 0x25
+#define MODE4_SDR 0x06
+#define MODE4_DDR 0x26
+#define MODE8_SDR 0x07
+#define MODE8_DDR 0x27
+#define WRITE_SDR 0x08
+#define WRITE_DDR 0x28
+#define READ_SDR 0x09
+#define READ_DDR 0x29
+#define LEARN_SDR 0x0A
+#define LEARN_DDR 0x2A
+#define DATSZ_SDR 0x0B
+#define DATSZ_DDR 0x2B
+#define DUMMY_SDR 0x0C
+#define DUMMY_DDR 0x2C
+#define DUMMY_RWDS_SDR 0x0D
+#define DUMMY_RWDS_DDR 0x2D
+#define JMP_ON_CS 0x1F
+#define STOP 0
+
+#define FLEXSPI_1PAD 0
+#define FLEXSPI_2PAD 1
+#define FLEXSPI_4PAD 2
+#define FLEXSPI_8PAD 3
+
+
+/*! @name LUT - LUT 0..LUT 63 */
+/*! @{ */
+#define FLEXSPI_LUT_OPERAND0_MASK (0xFFU)
+#define FLEXSPI_LUT_OPERAND0_SHIFT (0U)
+/*! OPERAND0 - OPERAND0
+ */
+#define FLEXSPI_LUT_OPERAND0(x) (((uint32_t)(((uint32_t)(x)) << FLEXSPI_LUT_OPERAND0_SHIFT)) & FLEXSPI_LUT_OPERAND0_MASK)
+#define FLEXSPI_LUT_NUM_PADS0_MASK (0x300U)
+#define FLEXSPI_LUT_NUM_PADS0_SHIFT (8U)
+/*! NUM_PADS0 - NUM_PADS0
+ */
+#define FLEXSPI_LUT_NUM_PADS0(x) (((uint32_t)(((uint32_t)(x)) << FLEXSPI_LUT_NUM_PADS0_SHIFT)) & FLEXSPI_LUT_NUM_PADS0_MASK)
+#define FLEXSPI_LUT_OPCODE0_MASK (0xFC00U)
+#define FLEXSPI_LUT_OPCODE0_SHIFT (10U)
+/*! OPCODE0 - OPCODE
+ */
+#define FLEXSPI_LUT_OPCODE0(x) (((uint32_t)(((uint32_t)(x)) << FLEXSPI_LUT_OPCODE0_SHIFT)) & FLEXSPI_LUT_OPCODE0_MASK)
+#define FLEXSPI_LUT_OPERAND1_MASK (0xFF0000U)
+#define FLEXSPI_LUT_OPERAND1_SHIFT (16U)
+/*! OPERAND1 - OPERAND1
+ */
+#define FLEXSPI_LUT_OPERAND1(x) (((uint32_t)(((uint32_t)(x)) << FLEXSPI_LUT_OPERAND1_SHIFT)) & FLEXSPI_LUT_OPERAND1_MASK)
+#define FLEXSPI_LUT_NUM_PADS1_MASK (0x3000000U)
+#define FLEXSPI_LUT_NUM_PADS1_SHIFT (24U)
+/*! NUM_PADS1 - NUM_PADS1
+ */
+#define FLEXSPI_LUT_NUM_PADS1(x) (((uint32_t)(((uint32_t)(x)) << FLEXSPI_LUT_NUM_PADS1_SHIFT)) & FLEXSPI_LUT_NUM_PADS1_MASK)
+#define FLEXSPI_LUT_OPCODE1_MASK (0xFC000000U)
+#define FLEXSPI_LUT_OPCODE1_SHIFT (26U)
+/*! OPCODE1 - OPCODE1
+ */
+#define FLEXSPI_LUT_OPCODE1(x) (((uint32_t)(((uint32_t)(x)) << FLEXSPI_LUT_OPCODE1_SHIFT)) & FLEXSPI_LUT_OPCODE1_MASK)
+/*! @} */
+
+#define FLEXSPI_LUT_SEQ(cmd0, pad0, op0, cmd1, pad1, op1) \
+ (FLEXSPI_LUT_OPERAND0(op0) | FLEXSPI_LUT_NUM_PADS0(pad0) | FLEXSPI_LUT_OPCODE0(cmd0) | FLEXSPI_LUT_OPERAND1(op1) | \
+ FLEXSPI_LUT_NUM_PADS1(pad1) | FLEXSPI_LUT_OPCODE1(cmd1))
+
+//!@brief Definitions for FlexSPI Serial Clock Frequency
+typedef enum _FlexSpiSerialClockFreq
+{
+ kFlexSpiSerialClk_30MHz = 1,
+ kFlexSpiSerialClk_50MHz = 2,
+ kFlexSpiSerialClk_60MHz = 3,
+ kFlexSpiSerialClk_75MHz = 4,
+ kFlexSpiSerialClk_80MHz = 5,
+ kFlexSpiSerialClk_100MHz = 6,
+ kFlexSpiSerialClk_120MHz = 7,
+ kFlexSpiSerialClk_133MHz = 8,
+ kFlexSpiSerialClk_166MHz = 9,
+} flexspi_serial_clk_freq_t;
+
+//!@brief FlexSPI clock configuration type
+enum
+{
+ kFlexSpiClk_SDR, //!< Clock configure for SDR mode
+ kFlexSpiClk_DDR, //!< Clock configurat for DDR mode
+};
+
+//!@brief FlexSPI Read Sample Clock Source definition
+typedef enum _FlashReadSampleClkSource
+{
+ kFlexSPIReadSampleClk_LoopbackInternally = 0,
+ kFlexSPIReadSampleClk_LoopbackFromDqsPad = 1,
+ kFlexSPIReadSampleClk_LoopbackFromSckPad = 2,
+ kFlexSPIReadSampleClk_ExternalInputFromDqsPad = 3,
+} flexspi_read_sample_clk_t;
+
+//!@brief Misc feature bit definitions
+enum
+{
+ kFlexSpiMiscOffset_DiffClkEnable = 0, //!< Bit for Differential clock enable
+ kFlexSpiMiscOffset_Ck2Enable = 1, //!< Bit for CK2 enable
+ kFlexSpiMiscOffset_ParallelEnable = 2, //!< Bit for Parallel mode enable
+ kFlexSpiMiscOffset_WordAddressableEnable = 3, //!< Bit for Word Addressable enable
+ kFlexSpiMiscOffset_SafeConfigFreqEnable = 4, //!< Bit for Safe Configuration Frequency enable
+ kFlexSpiMiscOffset_PadSettingOverrideEnable = 5, //!< Bit for Pad setting override enable
+ kFlexSpiMiscOffset_DdrModeEnable = 6, //!< Bit for DDR clock confiuration indication.
+};
+
+//!@brief Flash Type Definition
+enum
+{
+ kFlexSpiDeviceType_SerialNOR = 1, //!< Flash devices are Serial NOR
+ kFlexSpiDeviceType_SerialNAND = 2, //!< Flash devices are Serial NAND
+ kFlexSpiDeviceType_SerialRAM = 3, //!< Flash devices are Serial RAM/HyperFLASH
+ kFlexSpiDeviceType_MCP_NOR_NAND = 0x12, //!< Flash device is MCP device, A1 is Serial NOR, A2 is Serial NAND
+ kFlexSpiDeviceType_MCP_NOR_RAM = 0x13, //!< Flash deivce is MCP device, A1 is Serial NOR, A2 is Serial RAMs
+};
+
+//!@brief Flash Pad Definitions
+enum
+{
+ kSerialFlash_1Pad = 1,
+ kSerialFlash_2Pads = 2,
+ kSerialFlash_4Pads = 4,
+ kSerialFlash_8Pads = 8,
+};
+
+//!@brief FlexSPI LUT Sequence structure
+typedef struct __attribute__((packed, scalar_storage_order("little-endian"))) _lut_sequence
+{
+ uint8_t seqNum; //!< Sequence Number, valid number: 1-16
+ uint8_t seqId; //!< Sequence Index, valid number: 0-15
+ uint16_t reserved;
+} flexspi_lut_seq_t;
+
+//!@brief Flash Configuration Command Type
+enum
+{
+ kDeviceConfigCmdType_Generic, //!< Generic command, for example: configure dummy cycles, drive strength, etc
+ kDeviceConfigCmdType_QuadEnable, //!< Quad Enable command
+ kDeviceConfigCmdType_Spi2Xpi, //!< Switch from SPI to DPI/QPI/OPI mode
+ kDeviceConfigCmdType_Xpi2Spi, //!< Switch from DPI/QPI/OPI to SPI mode
+ kDeviceConfigCmdType_Spi2NoCmd, //!< Switch to 0-4-4/0-8-8 mode
+ kDeviceConfigCmdType_Reset, //!< Reset device command
+};
+
+//!@brief FlexSPI Memory Configuration Block
+typedef struct __attribute__((packed, scalar_storage_order("little-endian"))) _FlexSPIConfig
+{
+ uint32_t tag; //!< [0x000-0x003] Tag, fixed value 0x42464346UL
+ uint32_t version; //!< [0x004-0x007] Version,[31:24] -'V', [23:16] - Major, [15:8] - Minor, [7:0] - bugfix
+ uint32_t reserved0; //!< [0x008-0x00b] Reserved for future use
+ uint8_t readSampleClkSrc; //!< [0x00c-0x00c] Read Sample Clock Source, valid value: 0/1/3
+ uint8_t csHoldTime; //!< [0x00d-0x00d] CS hold time, default value: 3
+ uint8_t csSetupTime; //!< [0x00e-0x00e] CS setup time, default value: 3
+ uint8_t columnAddressWidth; //!< [0x00f-0x00f] Column Address with, for HyperBus protocol, it is fixed to 3, For
+ //! Serial NAND, need to refer to datasheet
+ uint8_t deviceModeCfgEnable; //!< [0x010-0x010] Device Mode Configure enable flag, 1 - Enable, 0 - Disable
+ uint8_t deviceModeType; //!< [0x011-0x011] Specify the configuration command type:Quad Enable, DPI/QPI/OPI switch,
+ //! Generic configuration, etc.
+ uint16_t waitTimeCfgCommands; //!< [0x012-0x013] Wait time for all configuration commands, unit: 100us, Used for
+ //! DPI/QPI/OPI switch or reset command
+ flexspi_lut_seq_t deviceModeSeq; //!< [0x014-0x017] Device mode sequence info, [7:0] - LUT sequence id, [15:8] - LUt
+ //! sequence number, [31:16] Reserved
+ uint32_t deviceModeArg; //!< [0x018-0x01b] Argument/Parameter for device configuration
+ uint8_t configCmdEnable; //!< [0x01c-0x01c] Configure command Enable Flag, 1 - Enable, 0 - Disable
+ uint8_t configModeType[3]; //!< [0x01d-0x01f] Configure Mode Type, similar as deviceModeTpe
+ flexspi_lut_seq_t
+ configCmdSeqs[3]; //!< [0x020-0x02b] Sequence info for Device Configuration command, similar as deviceModeSeq
+ uint32_t reserved1; //!< [0x02c-0x02f] Reserved for future use
+ uint32_t configCmdArgs[3]; //!< [0x030-0x03b] Arguments/Parameters for device Configuration commands
+ uint32_t reserved2; //!< [0x03c-0x03f] Reserved for future use
+ uint32_t controllerMiscOption; //!< [0x040-0x043] Controller Misc Options, see Misc feature bit definitions for more
+ //! details
+ uint8_t deviceType; //!< [0x044-0x044] Device Type: See Flash Type Definition for more details
+ uint8_t sflashPadType; //!< [0x045-0x045] Serial Flash Pad Type: 1 - Single, 2 - Dual, 4 - Quad, 8 - Octal
+ uint8_t serialClkFreq; //!< [0x046-0x046] Serial Flash Frequencey, device specific definitions, See System Boot
+ //! Chapter for more details
+ uint8_t lutCustomSeqEnable; //!< [0x047-0x047] LUT customization Enable, it is required if the program/erase cannot
+ //! be done using 1 LUT sequence, currently, only applicable to HyperFLASH
+ uint32_t reserved3[2]; //!< [0x048-0x04f] Reserved for future use
+ uint32_t sflashA1Size; //!< [0x050-0x053] Size of Flash connected to A1
+ uint32_t sflashA2Size; //!< [0x054-0x057] Size of Flash connected to A2
+ uint32_t sflashB1Size; //!< [0x058-0x05b] Size of Flash connected to B1
+ uint32_t sflashB2Size; //!< [0x05c-0x05f] Size of Flash connected to B2
+ uint32_t csPadSettingOverride; //!< [0x060-0x063] CS pad setting override value
+ uint32_t sclkPadSettingOverride; //!< [0x064-0x067] SCK pad setting override value
+ uint32_t dataPadSettingOverride; //!< [0x068-0x06b] data pad setting override value
+ uint32_t dqsPadSettingOverride; //!< [0x06c-0x06f] DQS pad setting override value
+ uint32_t timeoutInMs; //!< [0x070-0x073] Timeout threshold for read status command
+ uint32_t commandInterval; //!< [0x074-0x077] CS deselect interval between two commands
+ uint16_t dataValidTime[2]; //!< [0x078-0x07b] CLK edge to data valid time for PORT A and PORT B, in terms of 0.1ns
+ uint16_t busyOffset; //!< [0x07c-0x07d] Busy offset, valid value: 0-31
+ uint16_t busyBitPolarity; //!< [0x07e-0x07f] Busy flag polarity, 0 - busy flag is 1 when flash device is busy, 1 -
+ //! busy flag is 0 when flash device is busy
+ uint32_t lookupTable[64]; //!< [0x080-0x17f] Lookup table holds Flash command sequences
+ flexspi_lut_seq_t lutCustomSeq[12]; //!< [0x180-0x1af] Customizable LUT Sequences
+ uint32_t reserved4[4]; //!< [0x1b0-0x1bf] Reserved for future use
+} flexspi_mem_config_t;
+
+/* */
+#define NOR_CMD_INDEX_READ CMD_INDEX_READ //!< 0
+#define NOR_CMD_INDEX_READSTATUS CMD_INDEX_READSTATUS //!< 1
+#define NOR_CMD_INDEX_WRITEENABLE CMD_INDEX_WRITEENABLE //!< 2
+#define NOR_CMD_INDEX_ERASESECTOR 3 //!< 3
+#define NOR_CMD_INDEX_PAGEPROGRAM CMD_INDEX_WRITE //!< 4
+#define NOR_CMD_INDEX_CHIPERASE 5 //!< 5
+#define NOR_CMD_INDEX_DUMMY 6 //!< 6
+#define NOR_CMD_INDEX_ERASEBLOCK 7 //!< 7
+
+#define NOR_CMD_LUT_SEQ_IDX_READ CMD_LUT_SEQ_IDX_READ //!< 0 READ LUT sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_READSTATUS \
+ CMD_LUT_SEQ_IDX_READSTATUS //!< 1 Read Status LUT sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_READSTATUS_XPI \
+ 2 //!< 2 Read status DPI/QPI/OPI sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_WRITEENABLE \
+ CMD_LUT_SEQ_IDX_WRITEENABLE //!< 3 Write Enable sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_WRITEENABLE_XPI \
+ 4 //!< 4 Write Enable DPI/QPI/OPI sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_ERASESECTOR 5 //!< 5 Erase Sector sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_ERASEBLOCK 8 //!< 8 Erase Block sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_PAGEPROGRAM \
+ CMD_LUT_SEQ_IDX_WRITE //!< 9 Program sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_CHIPERASE 11 //!< 11 Chip Erase sequence in lookupTable id stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_READ_SFDP 13 //!< 13 Read SFDP sequence in lookupTable id stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_RESTORE_NOCMD \
+ 14 //!< 14 Restore 0-4-4/0-8-8 mode sequence id in lookupTable stored in config block
+#define NOR_CMD_LUT_SEQ_IDX_EXIT_NOCMD \
+ 15 //!< 15 Exit 0-4-4/0-8-8 mode sequence id in lookupTable stored in config blobk
+
+/*
+ * Serial NOR configuration block
+ */
+typedef struct __attribute__((packed, scalar_storage_order("little-endian"))) _flexspi_nor_config
+{
+ flexspi_mem_config_t memConfig; //!< Common memory configuration info via FlexSPI
+ uint32_t pageSize; //!< Page size of Serial NOR
+ uint32_t sectorSize; //!< Sector size of Serial NOR
+ uint8_t ipcmdSerialClkFreq; //!< Clock frequency for IP command
+ uint8_t isUniformBlockSize; //!< Sector/Block size is the same
+ uint8_t reserved0[2]; //!< Reserved for future use
+ uint8_t serialNorType; //!< Serial NOR Flash type: 0/1/2/3
+ uint8_t needExitNoCmdMode; //!< Need to exit NoCmd mode before other IP command
+ uint8_t halfClkForNonReadCmd; //!< Half the Serial Clock for non-read command: true/false
+ uint8_t needRestoreNoCmdMode; //!< Need to Restore NoCmd mode after IP commmand execution
+ uint32_t blockSize; //!< Block size
+ uint32_t reserve2[11]; //!< Reserved for future use
+} flexspi_nor_config_t;
+
+#endif /* __FLEXSPI_NOR_CONFIG__ */
--- /dev/null
+#include <stdio.h>
+#include <stdlib.h>
+#include <stdint.h>
+#include <string.h>
+#include <errno.h>
+#include <unistd.h>
+#include <stdbool.h>
+#include "flash.h"
+#include "flash_confs.h"
+
+size_t get_name_match(const flash_configs* , const char * name);
+void help(int code);
+void prepend(FILE * fno, size_t offset);
+int main(int argc, char *argv[]){
+
+ char name[32];
+ char fname[32];
+ int opt;
+ size_t index = 0;
+ size_t padding = 0x1000; // default offset for nor
+ size_t bin = 0;
+ FILE * fnum;
+ const flash_configs * configs = get_flash_confs();
+ const flexspi_nor_config_t * config;
+ while ((opt = getopt(argc, argv, "p:n:o:b:")) != -1)
+ {
+ errno = 0;
+ switch (opt)
+ {
+ case 'p':
+ padding = strtol(optarg, NULL, 0);
+ if (errno) {
+ printf("Invalid value for -%c.\n", opt);
+ help(-3);
+ }
+ break;
+ case 'n':
+ strncpy(name,optarg,32);
+ break;
+ case 'o':
+ strncpy(fname,optarg,32);
+ break;
+ case 'b':
+ bin = strtol(optarg, NULL, 0);
+ if (errno) {
+ printf("Invalid value for -%c.\n", opt);
+ help(-3);
+ }
+ break;
+ case 'h':
+ help(0);
+ break;
+ default:
+ help(-3);
+ break;
+ }
+ }
+
+ if(!strnlen(fname,32))
+ puts("Need an output file name.");
+ if(!strnlen(name,32))
+ puts("Need a flash config name.");
+ if(!strnlen(name,32) || !strnlen(fname,32))
+ help(-3);
+
+ index = get_name_match(configs,name);
+ if(index == -1){
+ printf("No match found for %s!\nExiting...\n",name);
+ exit(-2);
+ }
+ printf("Match found using %s flash config.\n",configs[index].name);
+
+ config = &configs[index].config;
+
+ fnum = fopen(fname,"wb+");
+ if(!fnum){
+ printf("Can't open %s for writing!\nExiting...\n",fname);
+ exit(-1);
+ }
+
+ fwrite(config,sizeof(flexspi_nor_config_t),1,fnum);
+ for(size_t i = sizeof(flexspi_nor_config_t); i < padding;i++)
+ fputc(0xff,fnum);
+ if(bin)
+ prepend(fnum,bin);
+ fclose(fnum);
+ puts("Done!");
+ return 0;
+}
+
+size_t get_name_match(const flash_configs* configs, const char * name){
+ size_t i = 0;
+ while(*configs[i].name){
+ if(strncmp(configs[i].name,name,32) == 0)
+ return i;
+ i++;
+ }
+ return -1;
+}
+void prepend(FILE * fno, size_t offset){
+ FILE * SPL, * uboot;
+ char * buf;
+ size_t sz;
+ uboot = fopen("u-boot.img","r");
+ if(!uboot){
+ puts("Can't open u-boot.img for reading!\nExiting...");
+ fclose(fno);
+ exit(-1);
+ }
+ SPL = fopen("SPL","r");
+ if(!SPL){
+ puts("Can't open SPL for reading!\nExiting...");
+ fclose(uboot);
+ fclose(fno);
+ exit(-1);
+ }
+ fseek(SPL, 0, SEEK_END);
+ sz = ftell(SPL);
+ buf = malloc(sz);
+ rewind(SPL);
+ fread(buf,sz,1,SPL);
+ fwrite(buf,sz,1,fno);
+
+ for(size_t i = ftell(fno); i < offset;i++)
+ fputc(0xff,fno);
+
+ fseek(uboot, 0, SEEK_END);
+ sz = ftell(uboot);
+ buf = realloc(buf, sz);
+ rewind(uboot);
+ fread(buf,sz,1,uboot);
+ fwrite(buf,sz,1,fno);
+ free(buf);
+
+ fclose(SPL);
+ fclose(uboot);
+}
+
+void help(int code){
+ puts("help");
+ exit(code);
+}
\ No newline at end of file
projects / imx_flashconf.git / commitdiff