-/* Start (run) and stop the inferior process, for GDB.
- Copyright 1986, 1987, 1988, 1989, 1991, 1992 Free Software Foundation, Inc.
+/* Target-struct-independent code to start (run) and stop an inferior process.
+ Copyright 1986, 1987, 1988, 1989, 1991, 1992, 1993, 1994
+ Free Software Foundation, Inc.
This file is part of GDB.
along with this program; if not, write to the Free Software
Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */
-/* Notes on the algorithm used in wait_for_inferior to determine if we
- just did a subroutine call when stepping. We have the following
- information at that point:
-
- Current and previous (just before this step) pc.
- Current and previous sp.
- Current and previous start of current function.
-
- If the starts of the functions don't match, then
-
- a) We did a subroutine call.
-
- In this case, the pc will be at the beginning of a function.
-
- b) We did a subroutine return.
-
- Otherwise.
-
- c) We did a longjmp.
-
- If we did a longjump, we were doing "nexti", since a next would
- have attempted to skip over the assembly language routine in which
- the longjmp is coded and would have simply been the equivalent of a
- continue. I consider this ok behaivior. We'd like one of two
- things to happen if we are doing a nexti through the longjmp()
- routine: 1) It behaves as a stepi, or 2) It acts like a continue as
- above. Given that this is a special case, and that anybody who
- thinks that the concept of sub calls is meaningful in the context
- of a longjmp, I'll take either one. Let's see what happens.
-
- Acts like a subroutine return. I can handle that with no problem
- at all.
-
- -->So: If the current and previous beginnings of the current
- function don't match, *and* the pc is at the start of a function,
- we've done a subroutine call. If the pc is not at the start of a
- function, we *didn't* do a subroutine call.
-
- -->If the beginnings of the current and previous function do match,
- either:
-
- a) We just did a recursive call.
-
- In this case, we would be at the very beginning of a
- function and 1) it will have a prologue (don't jump to
- before prologue, or 2) (we assume here that it doesn't have
- a prologue) there will have been a change in the stack
- pointer over the last instruction. (Ie. it's got to put
- the saved pc somewhere. The stack is the usual place. In
- a recursive call a register is only an option if there's a
- prologue to do something with it. This is even true on
- register window machines; the prologue sets up the new
- window. It might not be true on a register window machine
- where the call instruction moved the register window
- itself. Hmmm. One would hope that the stack pointer would
- also change. If it doesn't, somebody send me a note, and
- I'll work out a more general theory.
- so) on all machines I'm aware of:
-
- m68k: Call changes stack pointer. Regular jumps don't.
-
- sparc: Recursive calls must have frames and therefor,
- prologues.
-
- vax: All calls have frames and hence change the
- stack pointer.
-
- b) We did a return from a recursive call. I don't see that we
- have either the ability or the need to distinguish this
- from an ordinary jump. The stack frame will be printed
- when and if the frame pointer changes; if we are in a
- function without a frame pointer, it's the users own
- lookout.
-
- c) We did a jump within a function. We assume that this is
- true if we didn't do a recursive call.
-
- d) We are in no-man's land ("I see no symbols here"). We
- don't worry about this; it will make calls look like simple
- jumps (and the stack frames will be printed when the frame
- pointer moves), which is a reasonably non-violent response.
-*/
-
#include "defs.h"
#include <string.h>
+#include <ctype.h>
#include "symtab.h"
#include "frame.h"
#include "inferior.h"
#include "breakpoint.h"
#include "wait.h"
#include "gdbcore.h"
-#include "command.h"
-#include "terminal.h" /* For #ifdef TIOCGPGRP and new_tty */
+#include "gdbcmd.h"
#include "target.h"
+#include "thread.h"
#include <signal.h>
#include <sys/file.h>
#endif
-#ifdef SET_STACK_LIMIT_HUGE
-#include <sys/time.h>
-#include <sys/resource.h>
-
-extern int original_stack_limit;
-#endif /* SET_STACK_LIMIT_HUGE */
-
/* Prototypes for local functions */
static void
static void
handle_command PARAMS ((char *, int));
-static void
-sig_print_info PARAMS ((int));
+static void sig_print_info PARAMS ((enum target_signal));
static void
sig_print_header PARAMS ((void));
-static void
-remove_step_breakpoint PARAMS ((void));
-
-static void
-insert_step_breakpoint PARAMS ((void));
-
-static void
-resume PARAMS ((int, int));
-
static void
resume_cleanups PARAMS ((int));
-extern char **environ;
-
-extern struct target_ops child_ops; /* In inftarg.c */
-
-/* Sigtramp is a routine that the kernel calls (which then calls the
- signal handler). On most machines it is a library routine that
- is linked into the executable.
-
- This macro, given a program counter value and the name of the
- function in which that PC resides (which can be null if the
- name is not known), returns nonzero if the PC and name show
- that we are in sigtramp.
-
- On most machines just see if the name is sigtramp (and if we have
- no name, assume we are not in sigtramp). */
-#if !defined (IN_SIGTRAMP)
-#define IN_SIGTRAMP(pc, name) \
- (name && !strcmp ("_sigtramp", name))
-#endif
+static int
+hook_stop_stub PARAMS ((char *));
/* GET_LONGJMP_TARGET returns the PC at which longjmp() will resume the
program. It needs to examine the jmp_buf argument and extract the PC
#endif
/* For SVR4 shared libraries, each call goes through a small piece of
- trampoline code in the ".init" section. IN_SOLIB_TRAMPOLINE evaluates
+ trampoline code in the ".plt" section. IN_SOLIB_TRAMPOLINE evaluates
to nonzero if we are current stopped in one of these. */
#ifndef IN_SOLIB_TRAMPOLINE
#define IN_SOLIB_TRAMPOLINE(pc,name) 0
#endif
-/* Notify other parts of gdb that might care that signal handling may
- have changed for one or more signals. */
-#ifndef NOTICE_SIGNAL_HANDLING_CHANGE
-#define NOTICE_SIGNAL_HANDLING_CHANGE /* No actions */
-#endif
+/* On some systems, the PC may be left pointing at an instruction that won't
+ actually be executed. This is usually indicated by a bit in the PSW. If
+ we find ourselves in such a state, then we step the target beyond the
+ nullified instruction before returning control to the user so as to avoid
+ confusion. */
-#ifdef TDESC
-#include "tdesc.h"
-int safe_to_init_tdesc_context = 0;
-extern dc_dcontext_t current_context;
+#ifndef INSTRUCTION_NULLIFIED
+#define INSTRUCTION_NULLIFIED 0
#endif
/* Tables of how to react to signals; the user sets them. */
-static char *signal_stop;
-static char *signal_print;
-static char *signal_program;
-
-/* Nonzero if breakpoints are now inserted in the inferior. */
-/* Nonstatic for initialization during xxx_create_inferior. FIXME. */
+static unsigned char *signal_stop;
+static unsigned char *signal_print;
+static unsigned char *signal_program;
-/*static*/ int breakpoints_inserted;
+#define SET_SIGS(nsigs,sigs,flags) \
+ do { \
+ int signum = (nsigs); \
+ while (signum-- > 0) \
+ if ((sigs)[signum]) \
+ (flags)[signum] = 1; \
+ } while (0)
-/* Function inferior was in as of last step command. */
+#define UNSET_SIGS(nsigs,sigs,flags) \
+ do { \
+ int signum = (nsigs); \
+ while (signum-- > 0) \
+ if ((sigs)[signum]) \
+ (flags)[signum] = 0; \
+ } while (0)
-static struct symbol *step_start_function;
-/* Nonzero => address for special breakpoint for resuming stepping. */
+/* Command list pointer for the "stop" placeholder. */
-static CORE_ADDR step_resume_break_address;
+static struct cmd_list_element *stop_command;
-/* Pointer to orig contents of the byte where the special breakpoint is. */
+/* Nonzero if breakpoints are now inserted in the inferior. */
-static char step_resume_break_shadow[BREAKPOINT_MAX];
+static int breakpoints_inserted;
-/* Nonzero means the special breakpoint is a duplicate
- so it has not itself been inserted. */
+/* Function inferior was in as of last step command. */
-static int step_resume_break_duplicate;
+static struct symbol *step_start_function;
/* Nonzero if we are expecting a trace trap and should proceed from it. */
int stop_soon_quietly;
-/* Nonzero if pc has been changed by the debugger
- since the inferior stopped. */
-
-int pc_changed;
-
/* Nonzero if proceed is being used for a "finish" command or a similar
situation when stop_registers should be saved. */
STEP nonzero if we should step (zero to continue instead).
SIG is the signal to give the inferior (zero for none). */
-static void
+void
resume (step, sig)
int step;
- int sig;
+ enum target_signal sig;
{
struct cleanup *old_cleanups = make_cleanup (resume_cleanups, 0);
QUIT;
+#ifdef CANNOT_STEP_BREAKPOINT
+ /* Most targets can step a breakpoint instruction, thus executing it
+ normally. But if this one cannot, just continue and we will hit
+ it anyway. */
+ if (step && breakpoints_inserted && breakpoint_here_p (read_pc ()))
+ step = 0;
+#endif
+
#ifdef NO_SINGLE_STEP
if (step) {
single_step(sig); /* Do it the hard way, w/temp breakpoints */
DO_DEFERRED_STORES;
#endif
- target_resume (step, sig);
+ /* Install inferior's terminal modes. */
+ target_terminal_inferior ();
+
+ target_resume (-1, step, sig);
discard_cleanups (old_cleanups);
}
step_range_end = 0;
step_frame_address = 0;
step_over_calls = -1;
- step_resume_break_address = 0;
stop_after_trap = 0;
stop_soon_quietly = 0;
proceed_to_finish = 0;
void
proceed (addr, siggnal, step)
CORE_ADDR addr;
- int siggnal;
+ enum target_signal siggnal;
int step;
{
int oneproc = 0;
step one instruction before inserting breakpoints
so that we do not stop right away. */
- if (!pc_changed && breakpoint_here_p (read_pc ()))
+ if (breakpoint_here_p (read_pc ()))
+ oneproc = 1;
+
+#ifdef STEP_SKIPS_DELAY
+ /* Check breakpoint_here_p first, because breakpoint_here_p is fast
+ (it just checks internal GDB data structures) and STEP_SKIPS_DELAY
+ is slow (it needs to read memory from the target). */
+ if (breakpoint_here_p (read_pc () + 4)
+ && STEP_SKIPS_DELAY (read_pc ()))
oneproc = 1;
+#endif /* STEP_SKIPS_DELAY */
}
else
- {
- write_register (PC_REGNUM, addr);
-#ifdef NPC_REGNUM
- write_register (NPC_REGNUM, addr + 4);
-#ifdef NNPC_REGNUM
- write_register (NNPC_REGNUM, addr + 8);
-#endif
-#endif
- }
+ write_pc (addr);
if (trap_expected_after_continue)
{
breakpoints_inserted = 1;
}
- /* Install inferior's terminal modes. */
- target_terminal_inferior ();
-
- if (siggnal >= 0)
+ if (siggnal != TARGET_SIGNAL_DEFAULT)
stop_signal = siggnal;
/* If this signal should not be seen by program,
give it zero. Used for debugging signals. */
- else if (stop_signal < NSIG && !signal_program[stop_signal])
- stop_signal= 0;
+ else if (!signal_program[stop_signal])
+ stop_signal = TARGET_SIGNAL_0;
/* Resume inferior. */
resume (oneproc || step || bpstat_should_step (), stop_signal);
static CORE_ADDR prev_sp;
static CORE_ADDR prev_func_start;
static char *prev_func_name;
+static CORE_ADDR prev_frame_address;
\f
-/* Start an inferior Unix child process and sets inferior_pid to its pid.
- EXEC_FILE is the file to run.
- ALLARGS is a string containing the arguments to the program.
- ENV is the environment vector to pass. Errors reported with error(). */
-
-#ifndef SHELL_FILE
-#define SHELL_FILE "/bin/sh"
-#endif
-
-void
-child_create_inferior (exec_file, allargs, env)
- char *exec_file;
- char *allargs;
- char **env;
-{
- int pid;
- char *shell_command;
- char *shell_file;
- static char default_shell_file[] = SHELL_FILE;
- int len;
- int pending_execs;
- /* Set debug_fork then attach to the child while it sleeps, to debug. */
- static int debug_fork = 0;
- /* This is set to the result of setpgrp, which if vforked, will be visible
- to you in the parent process. It's only used by humans for debugging. */
- static int debug_setpgrp = 657473;
- char **save_our_env;
-
- /* The user might want tilde-expansion, and in general probably wants
- the program to behave the same way as if run from
- his/her favorite shell. So we let the shell run it for us.
- FIXME, this should probably search the local environment (as
- modified by the setenv command), not the env gdb inherited. */
- shell_file = getenv ("SHELL");
- if (shell_file == NULL)
- shell_file = default_shell_file;
-
- len = 5 + strlen (exec_file) + 1 + strlen (allargs) + 1 + /*slop*/ 10;
- /* If desired, concat something onto the front of ALLARGS.
- SHELL_COMMAND is the result. */
-#ifdef SHELL_COMMAND_CONCAT
- shell_command = (char *) alloca (strlen (SHELL_COMMAND_CONCAT) + len);
- strcpy (shell_command, SHELL_COMMAND_CONCAT);
-#else
- shell_command = (char *) alloca (len);
- shell_command[0] = '\0';
-#endif
- strcat (shell_command, "exec ");
- strcat (shell_command, exec_file);
- strcat (shell_command, " ");
- strcat (shell_command, allargs);
-
- /* exec is said to fail if the executable is open. */
- close_exec_file ();
-
- /* Retain a copy of our environment variables, since the child will
- replace the value of environ and if we're vforked, we have to
- restore it. */
- save_our_env = environ;
-
- /* Tell the terminal handling subsystem what tty we plan to run on;
- it will just record the information for later. */
-
- new_tty_prefork (inferior_io_terminal);
-
- /* It is generally good practice to flush any possible pending stdio
- output prior to doing a fork, to avoid the possibility of both the
- parent and child flushing the same data after the fork. */
-
- fflush (stdout);
- fflush (stderr);
-
-#if defined(USG) && !defined(HAVE_VFORK)
- pid = fork ();
-#else
- if (debug_fork)
- pid = fork ();
- else
- pid = vfork ();
-#endif
-
- if (pid < 0)
- perror_with_name ("vfork");
-
- if (pid == 0)
- {
- if (debug_fork)
- sleep (debug_fork);
-
-#ifdef TIOCGPGRP
- /* Run inferior in a separate process group. */
-#ifdef NEED_POSIX_SETPGID
- debug_setpgrp = setpgid (0, 0);
-#else
-#if defined(USG) && !defined(SETPGRP_ARGS)
- debug_setpgrp = setpgrp ();
-#else
- debug_setpgrp = setpgrp (getpid (), getpid ());
-#endif /* USG */
-#endif /* NEED_POSIX_SETPGID */
- if (debug_setpgrp == -1)
- perror("setpgrp failed in child");
-#endif /* TIOCGPGRP */
-
-#ifdef SET_STACK_LIMIT_HUGE
- /* Reset the stack limit back to what it was. */
- {
- struct rlimit rlim;
-
- getrlimit (RLIMIT_STACK, &rlim);
- rlim.rlim_cur = original_stack_limit;
- setrlimit (RLIMIT_STACK, &rlim);
- }
-#endif /* SET_STACK_LIMIT_HUGE */
-
- /* Ask the tty subsystem to switch to the one we specified earlier
- (or to share the current terminal, if none was specified). */
-
- new_tty ();
-
- /* Changing the signal handlers for the inferior after
- a vfork can also change them for the superior, so we don't mess
- with signals here. See comments in
- initialize_signals for how we get the right signal handlers
- for the inferior. */
-
-#ifdef USE_PROC_FS
- /* Use SVR4 /proc interface */
- proc_set_exec_trap ();
-#else
- /* "Trace me, Dr. Memory!" */
- call_ptrace (0, 0, (PTRACE_ARG3_TYPE) 0, 0);
-#endif
-
- /* There is no execlpe call, so we have to set the environment
- for our child in the global variable. If we've vforked, this
- clobbers the parent, but environ is restored a few lines down
- in the parent. By the way, yes we do need to look down the
- path to find $SHELL. Rich Pixley says so, and I agree. */
- environ = env;
- execlp (shell_file, shell_file, "-c", shell_command, (char *)0);
-
- fprintf (stderr, "Cannot exec %s: %s.\n", shell_file,
- safe_strerror (errno));
- fflush (stderr);
- _exit (0177);
- }
-
- /* Restore our environment in case a vforked child clob'd it. */
- environ = save_our_env;
-
- /* Now that we have a child process, make it our target. */
- push_target (&child_ops);
-
-#ifdef CREATE_INFERIOR_HOOK
- CREATE_INFERIOR_HOOK (pid);
-#endif
-
-/* The process was started by the fork that created it,
- but it will have stopped one instruction after execing the shell.
- Here we must get it up to actual execution of the real program. */
-
- inferior_pid = pid; /* Needed for wait_for_inferior stuff below */
-
- clear_proceed_status ();
-
- /* We will get a trace trap after one instruction.
- Continue it automatically. Eventually (after shell does an exec)
- it will get another trace trap. Then insert breakpoints and continue. */
-
-#ifdef START_INFERIOR_TRAPS_EXPECTED
- pending_execs = START_INFERIOR_TRAPS_EXPECTED;
-#else
- pending_execs = 2;
-#endif
-
- init_wait_for_inferior ();
-
- /* Set up the "saved terminal modes" of the inferior
- based on what modes we are starting it with. */
- target_terminal_init ();
-
- /* Install inferior's terminal modes. */
- target_terminal_inferior ();
-
- while (1)
- {
- stop_soon_quietly = 1; /* Make wait_for_inferior be quiet */
- wait_for_inferior ();
- if (stop_signal != SIGTRAP)
- {
- /* Let shell child handle its own signals in its own way */
- /* FIXME, what if child has exit()ed? Must exit loop somehow */
- resume (0, stop_signal);
- }
- else
- {
- /* We handle SIGTRAP, however; it means child did an exec. */
- if (0 == --pending_execs)
- break;
- resume (0, 0); /* Just make it go on */
- }
- }
- stop_soon_quietly = 0;
-
- /* We are now in the child process of interest, having exec'd the
- correct program, and are poised at the first instruction of the
- new program. */
-#ifdef SOLIB_CREATE_INFERIOR_HOOK
- SOLIB_CREATE_INFERIOR_HOOK (pid);
-#endif
-
- /* Should this perhaps just be a "proceed" call? FIXME */
- insert_step_breakpoint ();
- breakpoints_failed = insert_breakpoints ();
- if (!breakpoints_failed)
- {
- breakpoints_inserted = 1;
- target_terminal_inferior();
- /* Start the child program going on its first instruction, single-
- stepping if we need to. */
- resume (bpstat_should_step (), 0);
- wait_for_inferior ();
- normal_stop ();
- }
-}
-
/* Start remote-debugging of a machine over a serial link. */
void
prev_sp = 0;
prev_func_start = 0;
prev_func_name = NULL;
+ prev_frame_address = 0;
trap_expected_after_continue = 0;
breakpoints_inserted = 0;
- mark_breakpoints_out ();
- stop_signal = 0; /* Don't confuse first call to proceed(). */
-}
+ breakpoint_init_inferior ();
+ /* Don't confuse first call to proceed(). */
+ stop_signal = TARGET_SIGNAL_0;
+}
-/* Attach to process PID, then initialize for debugging it
- and wait for the trace-trap that results from attaching. */
-
-void
-child_attach (args, from_tty)
- char *args;
- int from_tty;
+static void
+delete_breakpoint_current_contents (arg)
+ PTR arg;
{
- char *exec_file;
- int pid;
-
- dont_repeat();
-
- if (!args)
- error_no_arg ("process-id to attach");
-
-#ifndef ATTACH_DETACH
- error ("Can't attach to a process on this machine.");
-#else
- pid = atoi (args);
-
- if (pid == getpid()) /* Trying to masturbate? */
- error ("I refuse to debug myself!");
-
- if (target_has_execution)
- {
- if (query ("A program is being debugged already. Kill it? "))
- target_kill ();
- else
- error ("Inferior not killed.");
- }
-
- exec_file = (char *) get_exec_file (1);
-
- if (from_tty)
- {
- printf ("Attaching program: %s pid %d\n",
- exec_file, pid);
- fflush (stdout);
- }
-
- attach (pid);
- inferior_pid = pid;
- push_target (&child_ops);
-
- mark_breakpoints_out ();
- target_terminal_init ();
- clear_proceed_status ();
- stop_soon_quietly = 1;
- /*proceed (-1, 0, -2);*/
- target_terminal_inferior ();
- wait_for_inferior ();
-#ifdef SOLIB_ADD
- SOLIB_ADD ((char *)0, from_tty, (struct target_ops *)0);
-#endif
- normal_stop ();
-#endif /* ATTACH_DETACH */
+ struct breakpoint **breakpointp = (struct breakpoint **)arg;
+ if (*breakpointp != NULL)
+ delete_breakpoint (*breakpointp);
}
\f
/* Wait for control to return from inferior to debugger.
void
wait_for_inferior ()
{
- WAITTYPE w;
+ struct cleanup *old_cleanups;
+ struct target_waitstatus w;
int another_trap;
int random_signal;
- CORE_ADDR stop_sp;
+ CORE_ADDR stop_sp = 0;
CORE_ADDR stop_func_start;
+ CORE_ADDR stop_func_end;
char *stop_func_name;
- CORE_ADDR prologue_pc, tmp;
- int stop_step_resume_break;
+ CORE_ADDR prologue_pc = 0, tmp;
struct symtab_and_line sal;
int remove_breakpoints_on_following_step = 0;
int current_line;
+ struct symtab *current_symtab;
int handling_longjmp = 0; /* FIXME */
+ struct breakpoint *step_resume_breakpoint = NULL;
+ struct breakpoint *through_sigtramp_breakpoint = NULL;
+ int pid;
+ old_cleanups = make_cleanup (delete_breakpoint_current_contents,
+ &step_resume_breakpoint);
+ make_cleanup (delete_breakpoint_current_contents,
+ &through_sigtramp_breakpoint);
sal = find_pc_line(prev_pc, 0);
current_line = sal.line;
+ current_symtab = sal.symtab;
+
+ /* Are we stepping? */
+#define CURRENTLY_STEPPING() \
+ ((through_sigtramp_breakpoint == NULL \
+ && !handling_longjmp \
+ && ((step_range_end && step_resume_breakpoint == NULL) \
+ || trap_expected)) \
+ || bpstat_should_step ())
while (1)
{
/* Clean up saved state that will become invalid. */
- pc_changed = 0;
flush_cached_frames ();
registers_changed ();
- target_wait (&w);
+ pid = target_wait (-1, &w);
-#ifdef SIGTRAP_STOP_AFTER_LOAD
-
- /* Somebody called load(2), and it gave us a "trap signal after load".
- Ignore it gracefully. */
+ switch (w.kind)
+ {
+ case TARGET_WAITKIND_LOADED:
+ /* Ignore it gracefully. */
+ if (breakpoints_inserted)
+ {
+ mark_breakpoints_out ();
+ insert_breakpoints ();
+ }
+ resume (0, TARGET_SIGNAL_0);
+ continue;
- SIGTRAP_STOP_AFTER_LOAD (w);
-#endif
+ case TARGET_WAITKIND_SPURIOUS:
+ resume (0, TARGET_SIGNAL_0);
+ continue;
- /* See if the process still exists; clean up if it doesn't. */
- if (WIFEXITED (w))
- {
+ case TARGET_WAITKIND_EXITED:
target_terminal_ours (); /* Must do this before mourn anyway */
- if (WEXITSTATUS (w))
+ if (w.value.integer)
printf_filtered ("\nProgram exited with code 0%o.\n",
- (unsigned int)WEXITSTATUS (w));
+ (unsigned int)w.value.integer);
else
if (!batch_mode())
printf_filtered ("\nProgram exited normally.\n");
- fflush (stdout);
+ gdb_flush (gdb_stdout);
target_mourn_inferior ();
#ifdef NO_SINGLE_STEP
one_stepped = 0;
#endif
stop_print_frame = 0;
- break;
- }
- else if (!WIFSTOPPED (w))
- {
+ goto stop_stepping;
+
+ case TARGET_WAITKIND_SIGNALLED:
stop_print_frame = 0;
- stop_signal = WTERMSIG (w);
+ stop_signal = w.value.sig;
target_terminal_ours (); /* Must do this before mourn anyway */
target_kill (); /* kill mourns as well */
-#ifdef PRINT_RANDOM_SIGNAL
- printf_filtered ("\nProgram terminated: ");
- PRINT_RANDOM_SIGNAL (stop_signal);
-#else
- printf_filtered ("\nProgram terminated with signal %d, %s\n",
- stop_signal, safe_strsignal (stop_signal));
-#endif
- printf_filtered ("The inferior process no longer exists.\n");
- fflush (stdout);
+ printf_filtered ("\nProgram terminated with signal %s, %s.\n",
+ target_signal_to_name (stop_signal),
+ target_signal_to_string (stop_signal));
+
+ printf_filtered ("The program no longer exists.\n");
+ gdb_flush (gdb_stdout);
#ifdef NO_SINGLE_STEP
one_stepped = 0;
#endif
+ goto stop_stepping;
+
+ case TARGET_WAITKIND_STOPPED:
+ /* This is the only case in which we keep going; the above cases
+ end in a continue or goto. */
break;
}
-
+
+ stop_signal = w.value.sig;
+
+ if (pid != inferior_pid)
+ {
+ int save_pid = inferior_pid;
+
+ inferior_pid = pid; /* Setup for target memory/regs */
+ registers_changed ();
+ stop_pc = read_pc ();
+ inferior_pid = save_pid;
+ registers_changed ();
+ }
+ else
+ stop_pc = read_pc ();
+
+ if (stop_signal == TARGET_SIGNAL_TRAP
+ && breakpoint_here_p (stop_pc - DECR_PC_AFTER_BREAK))
+ {
+ if (!breakpoint_thread_match (stop_pc - DECR_PC_AFTER_BREAK, pid))
+ {
+ /* Saw a breakpoint, but it was hit by the wrong thread. Just continue. */
+ if (breakpoints_inserted)
+ {
+ if (pid != inferior_pid)
+ {
+ int save_pid = inferior_pid;
+
+ inferior_pid = pid;
+ registers_changed ();
+ write_pc (stop_pc - DECR_PC_AFTER_BREAK);
+ inferior_pid = save_pid;
+ registers_changed ();
+ }
+ else
+ write_pc (stop_pc - DECR_PC_AFTER_BREAK);
+
+ remove_breakpoints ();
+ target_resume (pid, 1, TARGET_SIGNAL_0); /* Single step */
+ /* FIXME: What if a signal arrives instead of the single-step
+ happening? */
+ target_wait (pid, &w);
+ insert_breakpoints ();
+ }
+ target_resume (-1, 0, TARGET_SIGNAL_0);
+ continue;
+ }
+ else
+ if (pid != inferior_pid)
+ goto switch_thread;
+ }
+
+ if (pid != inferior_pid)
+ {
+ int printed = 0;
+
+ if (!in_thread_list (pid))
+ {
+ fprintf_unfiltered (gdb_stderr, "[New %s]\n", target_pid_to_str (pid));
+ add_thread (pid);
+
+ target_resume (-1, 0, TARGET_SIGNAL_0);
+ continue;
+ }
+ else
+ {
+ if (signal_print[stop_signal])
+ {
+ char *signame;
+
+ printed = 1;
+ target_terminal_ours_for_output ();
+ printf_filtered ("\nProgram received signal %s, %s.\n",
+ target_signal_to_name (stop_signal),
+ target_signal_to_string (stop_signal));
+ gdb_flush (gdb_stdout);
+ }
+
+ if (stop_signal == TARGET_SIGNAL_TRAP
+ || signal_stop[stop_signal])
+ {
+switch_thread:
+ inferior_pid = pid;
+ printf_filtered ("[Switching to %s]\n", target_pid_to_str (pid));
+
+ flush_cached_frames ();
+ registers_changed ();
+ trap_expected = 0;
+ if (step_resume_breakpoint)
+ {
+ delete_breakpoint (step_resume_breakpoint);
+ step_resume_breakpoint = NULL;
+ }
+
+ /* Not sure whether we need to blow this away too,
+ but probably it is like the step-resume
+ breakpoint. */
+ if (through_sigtramp_breakpoint)
+ {
+ delete_breakpoint (through_sigtramp_breakpoint);
+ through_sigtramp_breakpoint = NULL;
+ }
+ prev_pc = 0;
+ prev_sp = 0;
+ prev_func_name = NULL;
+ step_range_start = 0;
+ step_range_end = 0;
+ step_frame_address = 0;
+ handling_longjmp = 0;
+ another_trap = 0;
+ }
+ else
+ {
+ if (printed)
+ target_terminal_inferior ();
+
+ /* Clear the signal if it should not be passed. */
+ if (signal_program[stop_signal] == 0)
+ stop_signal = TARGET_SIGNAL_0;
+
+ target_resume (pid, 0, stop_signal);
+ continue;
+ }
+ }
+ }
+
#ifdef NO_SINGLE_STEP
if (one_stepped)
single_step (0); /* This actually cleans up the ss */
#endif /* NO_SINGLE_STEP */
- stop_pc = read_pc ();
- set_current_frame ( create_new_frame (read_register (FP_REGNUM),
- read_pc ()));
-
+ /* If PC is pointing at a nullified instruction, then step beyond
+ it so that the user won't be confused when GDB appears to be ready
+ to execute it. */
+
+ if (INSTRUCTION_NULLIFIED)
+ {
+ resume (1, 0);
+ continue;
+ }
+
+ set_current_frame (create_new_frame (read_fp (), stop_pc));
+ select_frame (get_current_frame (), 0);
+
+#ifdef HAVE_STEPPABLE_WATCHPOINT
+ /* It may not be necessary to disable the watchpoint to stop over
+ it. For example, the PA can (with some kernel cooperation)
+ single step over a watchpoint without disabling the watchpoint. */
+ if (STOPPED_BY_WATCHPOINT (w))
+ {
+ resume (1, 0);
+ continue;
+ }
+#endif
+
+#ifdef HAVE_NONSTEPPABLE_WATCHPOINT
+ /* It is far more common to need to disable a watchpoint
+ to step the inferior over it. FIXME. What else might
+ a debug register or page protection watchpoint scheme need
+ here? */
+ if (STOPPED_BY_WATCHPOINT (w))
+ {
+ remove_breakpoints ();
+ resume (1, 0);
+ insert_breakpoints ();
+ continue;
+ }
+#endif
+
stop_frame_address = FRAME_FP (get_current_frame ());
- stop_sp = read_register (SP_REGNUM);
+ stop_sp = read_sp ();
stop_func_start = 0;
stop_func_name = 0;
/* Don't care about return value; stop_func_start and stop_func_name
will both be 0 if it doesn't work. */
- (void) find_pc_partial_function (stop_pc, &stop_func_name,
- &stop_func_start);
+ find_pc_partial_function (stop_pc, &stop_func_name, &stop_func_start,
+ &stop_func_end);
stop_func_start += FUNCTION_START_OFFSET;
another_trap = 0;
bpstat_clear (&stop_bpstat);
stop_step = 0;
stop_stack_dummy = 0;
stop_print_frame = 1;
- stop_step_resume_break = 0;
random_signal = 0;
stopped_by_random_signal = 0;
breakpoints_failed = 0;
3) set random_signal to 1, and the decision between 1 and 2
will be made according to the signal handling tables. */
- stop_signal = WSTOPSIG (w);
-
/* First, distinguish signals caused by the debugger from signals
that have to do with the program's own actions.
Note that breakpoint insns may cause SIGTRAP or SIGILL
Here we detect when a SIGILL or SIGEMT is really a breakpoint
and change it to SIGTRAP. */
- if (stop_signal == SIGTRAP
+ if (stop_signal == TARGET_SIGNAL_TRAP
|| (breakpoints_inserted &&
- (stop_signal == SIGILL
-#ifdef SIGEMT
- || stop_signal == SIGEMT
-#endif
+ (stop_signal == TARGET_SIGNAL_ILL
+ || stop_signal == TARGET_SIGNAL_EMT
))
|| stop_soon_quietly)
{
- if (stop_signal == SIGTRAP && stop_after_trap)
+ if (stop_signal == TARGET_SIGNAL_TRAP && stop_after_trap)
{
stop_print_frame = 0;
break;
if just proceeded over a breakpoint.
However, if we are trying to proceed over a breakpoint
- and end up in sigtramp, then step_resume_break_address
+ and end up in sigtramp, then through_sigtramp_breakpoint
will be set and we should check whether we've hit the
step breakpoint. */
- if (stop_signal == SIGTRAP && trap_expected
- && step_resume_break_address == 0)
+ if (stop_signal == TARGET_SIGNAL_TRAP && trap_expected
+ && through_sigtramp_breakpoint == NULL)
bpstat_clear (&stop_bpstat);
else
{
/* See if there is a breakpoint at the current PC. */
+ stop_bpstat = bpstat_stop_status
+ (&stop_pc, stop_frame_address,
#if DECR_PC_AFTER_BREAK
- /* Notice the case of stepping through a jump
- that lands just after a breakpoint.
- Don't confuse that with hitting the breakpoint.
- What we check for is that 1) stepping is going on
- and 2) the pc before the last insn does not match
- the address of the breakpoint before the current pc. */
- if (prev_pc == stop_pc - DECR_PC_AFTER_BREAK
- || !step_range_end
- || step_resume_break_address
- || handling_longjmp /* FIXME */)
-#endif /* DECR_PC_AFTER_BREAK not zero */
- {
- /* See if we stopped at the special breakpoint for
- stepping over a subroutine call. If both are zero,
- this wasn't the reason for the stop. */
- if (step_resume_break_address
- && stop_pc - DECR_PC_AFTER_BREAK
- == step_resume_break_address)
- {
- stop_step_resume_break = 1;
- if (DECR_PC_AFTER_BREAK)
- {
- stop_pc -= DECR_PC_AFTER_BREAK;
- write_register (PC_REGNUM, stop_pc);
- pc_changed = 0;
- }
- }
- else
- {
- stop_bpstat =
- bpstat_stop_status (&stop_pc, stop_frame_address);
- /* Following in case break condition called a
- function. */
- stop_print_frame = 1;
- }
- }
+ /* Notice the case of stepping through a jump
+ that lands just after a breakpoint.
+ Don't confuse that with hitting the breakpoint.
+ What we check for is that 1) stepping is going on
+ and 2) the pc before the last insn does not match
+ the address of the breakpoint before the current pc. */
+ (prev_pc != stop_pc - DECR_PC_AFTER_BREAK
+ && CURRENTLY_STEPPING ())
+#else /* DECR_PC_AFTER_BREAK zero */
+ 0
+#endif /* DECR_PC_AFTER_BREAK zero */
+ );
+ /* Following in case break condition called a
+ function. */
+ stop_print_frame = 1;
}
-
- if (stop_signal == SIGTRAP)
+
+ if (stop_signal == TARGET_SIGNAL_TRAP)
random_signal
= !(bpstat_explains_signal (stop_bpstat)
|| trap_expected
- || stop_step_resume_break
+#ifndef CALL_DUMMY_BREAKPOINT_OFFSET
|| PC_IN_CALL_DUMMY (stop_pc, stop_sp, stop_frame_address)
- || (step_range_end && !step_resume_break_address));
+#endif /* No CALL_DUMMY_BREAKPOINT_OFFSET. */
+ || (step_range_end && step_resume_breakpoint == NULL));
else
{
random_signal
= !(bpstat_explains_signal (stop_bpstat)
- || stop_step_resume_break
/* End of a stack dummy. Some systems (e.g. Sony
news) give another signal besides SIGTRAP,
so check here as well as above. */
+#ifndef CALL_DUMMY_BREAKPOINT_OFFSET
|| PC_IN_CALL_DUMMY (stop_pc, stop_sp, stop_frame_address)
+#endif /* No CALL_DUMMY_BREAKPOINT_OFFSET. */
);
if (!random_signal)
- stop_signal = SIGTRAP;
+ stop_signal = TARGET_SIGNAL_TRAP;
}
}
else
random_signal = 1;
-
+
/* For the program's own signals, act according to
the signal handling tables. */
-
+
if (random_signal)
{
/* Signal not for debugging purposes. */
stopped_by_random_signal = 1;
- if (stop_signal >= NSIG
- || signal_print[stop_signal])
+ if (signal_print[stop_signal])
{
+ char *signame;
printed = 1;
target_terminal_ours_for_output ();
-#ifdef PRINT_RANDOM_SIGNAL
- PRINT_RANDOM_SIGNAL (stop_signal);
-#else
- printf_filtered ("\nProgram received signal %d, %s\n",
- stop_signal, safe_strsignal (stop_signal));
-#endif /* PRINT_RANDOM_SIGNAL */
- fflush (stdout);
+ printf_filtered ("\nProgram received signal %s, %s.\n",
+ target_signal_to_name (stop_signal),
+ target_signal_to_string (stop_signal));
+ gdb_flush (gdb_stdout);
}
- if (stop_signal >= NSIG
- || signal_stop[stop_signal])
+ if (signal_stop[stop_signal])
break;
/* If not going to stop, give terminal back
if we took it away. */
else if (printed)
target_terminal_inferior ();
- /* Note that virtually all the code below does `if !random_signal'.
- Perhaps this code should end with a goto or continue. At least
- one (now fixed) bug was caused by this -- a !random_signal was
- missing in one of the tests below. */
+ /* Clear the signal if it should not be passed. */
+ if (signal_program[stop_signal] == 0)
+ stop_signal = TARGET_SIGNAL_0;
+
+ /* I'm not sure whether this needs to be check_sigtramp2 or
+ whether it could/should be keep_going. */
+ goto check_sigtramp2;
}
/* Handle cases caused by hitting a breakpoint. */
+ {
+ CORE_ADDR jmp_buf_pc;
+ struct bpstat_what what;
+
+ what = bpstat_what (stop_bpstat);
- if (!random_signal)
- if (bpstat_explains_signal (stop_bpstat))
+ if (what.call_dummy)
{
- CORE_ADDR jmp_buf_pc;
+ stop_stack_dummy = 1;
+#ifdef HP_OS_BUG
+ trap_expected_after_continue = 1;
+#endif
+ }
- switch (stop_bpstat->breakpoint_at->type) /* FIXME */
+ switch (what.main_action)
+ {
+ case BPSTAT_WHAT_SET_LONGJMP_RESUME:
+ /* If we hit the breakpoint at longjmp, disable it for the
+ duration of this command. Then, install a temporary
+ breakpoint at the target of the jmp_buf. */
+ disable_longjmp_breakpoint();
+ remove_breakpoints ();
+ breakpoints_inserted = 0;
+ if (!GET_LONGJMP_TARGET(&jmp_buf_pc)) goto keep_going;
+
+ /* Need to blow away step-resume breakpoint, as it
+ interferes with us */
+ if (step_resume_breakpoint != NULL)
{
- /* If we hit the breakpoint at longjmp, disable it for the
- duration of this command. Then, install a temporary
- breakpoint at the target of the jmp_buf. */
- case bp_longjmp:
- disable_longjmp_breakpoint();
- remove_breakpoints ();
- breakpoints_inserted = 0;
- if (!GET_LONGJMP_TARGET(&jmp_buf_pc)) goto keep_going;
-
- /* Need to blow away step-resume breakpoint, as it
- interferes with us */
- remove_step_breakpoint ();
- step_resume_break_address = 0;
- stop_step_resume_break = 0;
-
-#if 0 /* FIXME - Need to implement nested temporary breakpoints */
- if (step_over_calls > 0)
- set_longjmp_resume_breakpoint(jmp_buf_pc,
- get_current_frame());
- else
-#endif /* 0 */
- set_longjmp_resume_breakpoint(jmp_buf_pc, NULL);
- handling_longjmp = 1; /* FIXME */
- goto keep_going;
+ delete_breakpoint (step_resume_breakpoint);
+ step_resume_breakpoint = NULL;
+ }
+ /* Not sure whether we need to blow this away too, but probably
+ it is like the step-resume breakpoint. */
+ if (through_sigtramp_breakpoint != NULL)
+ {
+ delete_breakpoint (through_sigtramp_breakpoint);
+ through_sigtramp_breakpoint = NULL;
+ }
- case bp_longjmp_resume:
- remove_breakpoints ();
- breakpoints_inserted = 0;
-#if 0 /* FIXME - Need to implement nested temporary breakpoints */
- if (step_over_calls
- && (stop_frame_address
- INNER_THAN step_frame_address))
- {
- another_trap = 1;
- goto keep_going;
- }
+#if 0
+ /* FIXME - Need to implement nested temporary breakpoints */
+ if (step_over_calls > 0)
+ set_longjmp_resume_breakpoint(jmp_buf_pc,
+ get_current_frame());
+ else
#endif /* 0 */
- disable_longjmp_breakpoint();
- handling_longjmp = 0; /* FIXME */
- break;
-
- default:
- fprintf(stderr, "Unknown breakpoint type %d\n",
- stop_bpstat->breakpoint_at->type);
- case bp_watchpoint:
- case bp_breakpoint:
- case bp_until:
- case bp_finish:
- /* Does a breakpoint want us to stop? */
- if (bpstat_stop (stop_bpstat))
- {
- stop_print_frame = bpstat_should_print (stop_bpstat);
- goto stop_stepping;
- }
- /* Otherwise, must remove breakpoints and single-step
- to get us past the one we hit. */
- else
- {
- remove_breakpoints ();
- remove_step_breakpoint ();
- breakpoints_inserted = 0;
- another_trap = 1;
- }
- break;
- }
- }
- else if (stop_step_resume_break)
- {
- /* But if we have hit the step-resumption breakpoint,
- remove it. It has done its job getting us here.
- The sp test is to make sure that we don't get hung
- up in recursive calls in functions without frame
- pointers. If the stack pointer isn't outside of
- where the breakpoint was set (within a routine to be
- stepped over), we're in the middle of a recursive
- call. Not true for reg window machines (sparc)
- because the must change frames to call things and
- the stack pointer doesn't have to change if it
- the bp was set in a routine without a frame (pc can
- be stored in some other window).
-
- The removal of the sp test is to allow calls to
- alloca. Nasty things were happening. Oh, well,
- gdb can only handle one level deep of lack of
- frame pointer. */
-
- /*
- Disable test for step_frame_address match so that we always stop even if the
- frames don't match. Reason: if we hit the step_resume_breakpoint, there is
- no way to temporarily disable it so that we can step past it. If we leave
- the breakpoint in, then we loop forever repeatedly hitting, but never
- getting past the breakpoint. This change keeps nexting over recursive
- function calls from hanging gdb.
- */
+ set_longjmp_resume_breakpoint(jmp_buf_pc, NULL);
+ handling_longjmp = 1; /* FIXME */
+ goto keep_going;
+
+ case BPSTAT_WHAT_CLEAR_LONGJMP_RESUME:
+ case BPSTAT_WHAT_CLEAR_LONGJMP_RESUME_SINGLE:
+ remove_breakpoints ();
+ breakpoints_inserted = 0;
#if 0
- if (* step_frame_address == 0
- || (step_frame_address == stop_frame_address))
-#endif
+ /* FIXME - Need to implement nested temporary breakpoints */
+ if (step_over_calls
+ && (stop_frame_address
+ INNER_THAN step_frame_address))
{
- remove_step_breakpoint ();
- step_resume_break_address = 0;
-
- /* If were waiting for a trap, hitting the step_resume_break
- doesn't count as getting it. */
- if (trap_expected)
- another_trap = 1;
+ another_trap = 1;
+ goto keep_going;
}
+#endif /* 0 */
+ disable_longjmp_breakpoint();
+ handling_longjmp = 0; /* FIXME */
+ if (what.main_action == BPSTAT_WHAT_CLEAR_LONGJMP_RESUME)
+ break;
+ /* else fallthrough */
+
+ case BPSTAT_WHAT_SINGLE:
+ if (breakpoints_inserted)
+ remove_breakpoints ();
+ breakpoints_inserted = 0;
+ another_trap = 1;
+ /* Still need to check other stuff, at least the case
+ where we are stepping and step out of the right range. */
+ break;
+
+ case BPSTAT_WHAT_STOP_NOISY:
+ stop_print_frame = 1;
+
+ /* We are about to nuke the step_resume_breakpoint and
+ through_sigtramp_breakpoint via the cleanup chain, so
+ no need to worry about it here. */
+
+ goto stop_stepping;
+
+ case BPSTAT_WHAT_STOP_SILENT:
+ stop_print_frame = 0;
+
+ /* We are about to nuke the step_resume_breakpoint and
+ through_sigtramp_breakpoint via the cleanup chain, so
+ no need to worry about it here. */
+
+ goto stop_stepping;
+
+ case BPSTAT_WHAT_STEP_RESUME:
+ delete_breakpoint (step_resume_breakpoint);
+ step_resume_breakpoint = NULL;
+ break;
+
+ case BPSTAT_WHAT_THROUGH_SIGTRAMP:
+ delete_breakpoint (through_sigtramp_breakpoint);
+ through_sigtramp_breakpoint = NULL;
+
+ /* If were waiting for a trap, hitting the step_resume_break
+ doesn't count as getting it. */
+ if (trap_expected)
+ another_trap = 1;
+ break;
+
+ case BPSTAT_WHAT_LAST:
+ /* Not a real code, but listed here to shut up gcc -Wall. */
+
+ case BPSTAT_WHAT_KEEP_CHECKING:
+ break;
}
+ }
/* We come here if we hit a breakpoint but should not
stop for it. Possibly we also were stepping
test for stepping. But, if not stepping,
do not stop. */
+#ifndef CALL_DUMMY_BREAKPOINT_OFFSET
+ /* This is the old way of detecting the end of the stack dummy.
+ An architecture which defines CALL_DUMMY_BREAKPOINT_OFFSET gets
+ handled above. As soon as we can test it on all of them, all
+ architectures should define it. */
+
/* If this is the breakpoint at the end of a stack dummy,
- just stop silently. */
- if (!random_signal
- && PC_IN_CALL_DUMMY (stop_pc, stop_sp, stop_frame_address))
- {
- stop_print_frame = 0;
- stop_stack_dummy = 1;
+ just stop silently, unless the user was doing an si/ni, in which
+ case she'd better know what she's doing. */
+
+ if (PC_IN_CALL_DUMMY (stop_pc, stop_sp, stop_frame_address)
+ && !step_range_end)
+ {
+ stop_print_frame = 0;
+ stop_stack_dummy = 1;
#ifdef HP_OS_BUG
- trap_expected_after_continue = 1;
+ trap_expected_after_continue = 1;
#endif
- break;
- }
-
- if (step_resume_break_address)
+ break;
+ }
+#endif /* No CALL_DUMMY_BREAKPOINT_OFFSET. */
+
+ if (step_resume_breakpoint)
/* Having a step-resume breakpoint overrides anything
else having to do with stepping commands until
that breakpoint is reached. */
- ;
+ /* I'm not sure whether this needs to be check_sigtramp2 or
+ whether it could/should be keep_going. */
+ goto check_sigtramp2;
+
+ if (step_range_end == 0)
+ /* Likewise if we aren't even stepping. */
+ /* I'm not sure whether this needs to be check_sigtramp2 or
+ whether it could/should be keep_going. */
+ goto check_sigtramp2;
+
/* If stepping through a line, keep going if still within it. */
- else if (!random_signal
- && step_range_end
- && stop_pc >= step_range_start
- && stop_pc < step_range_end
- /* The step range might include the start of the
- function, so if we are at the start of the
- step range and either the stack or frame pointers
- just changed, we've stepped outside */
- && !(stop_pc == step_range_start
- && stop_frame_address
- && (stop_sp INNER_THAN prev_sp
- || stop_frame_address != step_frame_address)))
+ if (stop_pc >= step_range_start
+ && stop_pc < step_range_end
+ /* The step range might include the start of the
+ function, so if we are at the start of the
+ step range and either the stack or frame pointers
+ just changed, we've stepped outside */
+ && !(stop_pc == step_range_start
+ && stop_frame_address
+ && (stop_sp INNER_THAN prev_sp
+ || stop_frame_address != step_frame_address)))
{
- ;
+ /* We might be doing a BPSTAT_WHAT_SINGLE and getting a signal.
+ So definately need to check for sigtramp here. */
+ goto check_sigtramp2;
}
-
+
/* We stepped out of the stepping range. See if that was due
to a subroutine call that we should proceed to the end of. */
- else if (!random_signal && step_range_end)
+
+ /* Did we just take a signal? */
+ if (IN_SIGTRAMP (stop_pc, stop_func_name)
+ && !IN_SIGTRAMP (prev_pc, prev_func_name))
{
- if (stop_func_start)
- {
- prologue_pc = stop_func_start;
- SKIP_PROLOGUE (prologue_pc);
- }
+ /* We've just taken a signal; go until we are back to
+ the point where we took it and one more. */
- /* Did we just take a signal? */
- if (IN_SIGTRAMP (stop_pc, stop_func_name)
- && !IN_SIGTRAMP (prev_pc, prev_func_name))
- {
- /* This code is needed at least in the following case:
- The user types "next" and then a signal arrives (before
- the "next" is done). */
- /* We've just taken a signal; go until we are back to
- the point where we took it and one more. */
- step_resume_break_address = prev_pc;
- step_resume_break_duplicate =
- breakpoint_here_p (step_resume_break_address);
- if (breakpoints_inserted)
- insert_step_breakpoint ();
- /* Make sure that the stepping range gets us past
- that instruction. */
- if (step_range_end == 1)
- step_range_end = (step_range_start = prev_pc) + 1;
- remove_breakpoints_on_following_step = 1;
- goto save_pc;
- }
+ /* This code is needed at least in the following case:
+ The user types "next" and then a signal arrives (before
+ the "next" is done). */
- /* ==> See comments at top of file on this algorithm. <==*/
-
- if ((stop_pc == stop_func_start
- || IN_SOLIB_TRAMPOLINE (stop_pc, stop_func_name))
- && (stop_func_start != prev_func_start
- || prologue_pc != stop_func_start
- || stop_sp != prev_sp))
- {
- /* It's a subroutine call.
- (0) If we are not stepping over any calls ("stepi"), we
- just stop.
- (1) If we're doing a "next", we want to continue through
- the call ("step over the call").
- (2) If we are in a function-call trampoline (a stub between
- the calling routine and the real function), locate
- the real function and change stop_func_start.
- (3) If we're doing a "step", and there are no debug symbols
- at the target of the call, we want to continue through
- it ("step over the call").
- (4) Otherwise, we want to stop soon, after the function
- prologue ("step into the call"). */
-
- if (step_over_calls == 0)
- {
- /* I presume that step_over_calls is only 0 when we're
- supposed to be stepping at the assembly language level. */
- stop_step = 1;
- break;
- }
+ /* Note that if we are stopped at a breakpoint, then we need
+ the step_resume breakpoint to override any breakpoints at
+ the same location, so that we will still step over the
+ breakpoint even though the signal happened. */
+
+ {
+ struct symtab_and_line sr_sal;
+
+ sr_sal.pc = prev_pc;
+ sr_sal.symtab = NULL;
+ sr_sal.line = 0;
+ /* We could probably be setting the frame to
+ prev_frame_address; the reason we don't is that it didn't used
+ to exist. */
+ step_resume_breakpoint =
+ set_momentary_breakpoint (sr_sal, NULL, bp_step_resume);
+ if (breakpoints_inserted)
+ insert_breakpoints ();
+ }
+
+ /* If this is stepi or nexti, make sure that the stepping range
+ gets us past that instruction. */
+ if (step_range_end == 1)
+ /* FIXME: Does this run afoul of the code below which, if
+ we step into the middle of a line, resets the stepping
+ range? */
+ step_range_end = (step_range_start = prev_pc) + 1;
- if (step_over_calls > 0)
- goto step_over_function;
+ remove_breakpoints_on_following_step = 1;
+ goto keep_going;
+ }
+
+ if (stop_func_start)
+ {
+ /* Do this after the IN_SIGTRAMP check; it might give
+ an error. */
+ prologue_pc = stop_func_start;
+ SKIP_PROLOGUE (prologue_pc);
+ }
+
+ if ((/* Might be a non-recursive call. If the symbols are missing
+ enough that stop_func_start == prev_func_start even though
+ they are really two functions, we will treat some calls as
+ jumps. */
+ stop_func_start != prev_func_start
+
+ /* Might be a recursive call if either we have a prologue
+ or the call instruction itself saves the PC on the stack. */
+ || prologue_pc != stop_func_start
+ || stop_sp != prev_sp)
+ && (/* PC is completely out of bounds of any known objfiles. Treat
+ like a subroutine call. */
+ ! stop_func_start
+
+ /* If we do a call, we will be at the start of a function... */
+ || stop_pc == stop_func_start
+
+ /* ...except on the Alpha with -O (and also Irix 5 and
+ perhaps others), in which we might call the address
+ after the load of gp. Since prologues don't contain
+ calls, we can't return to within one, and we don't
+ jump back into them, so this check is OK. */
+
+ || stop_pc < prologue_pc
+
+ /* If we end up in certain places, it means we did a subroutine
+ call. I'm not completely sure this is necessary now that we
+ have the above checks with stop_func_start (and now that
+ find_pc_partial_function is pickier). */
+ || IN_SOLIB_TRAMPOLINE (stop_pc, stop_func_name)
+
+ /* If none of the above apply, it is a jump within a function,
+ or a return from a subroutine. The other case is longjmp,
+ which can no longer happen here as long as the
+ handling_longjmp stuff is working. */
+ ))
+ {
+ /* It's a subroutine call. */
+
+ if (step_over_calls == 0)
+ {
+ /* I presume that step_over_calls is only 0 when we're
+ supposed to be stepping at the assembly language level
+ ("stepi"). Just stop. */
+ stop_step = 1;
+ break;
+ }
- tmp = SKIP_TRAMPOLINE_CODE (stop_pc);
- if (tmp != 0)
- stop_func_start = tmp;
+ if (step_over_calls > 0)
+ /* We're doing a "next". */
+ goto step_over_function;
+
+ /* If we are in a function call trampoline (a stub between
+ the calling routine and the real function), locate the real
+ function. That's what tells us (a) whether we want to step
+ into it at all, and (b) what prologue we want to run to
+ the end of, if we do step into it. */
+ tmp = SKIP_TRAMPOLINE_CODE (stop_pc);
+ if (tmp != 0)
+ stop_func_start = tmp;
+
+ /* If we have line number information for the function we
+ are thinking of stepping into, step into it.
+
+ If there are several symtabs at that PC (e.g. with include
+ files), just want to know whether *any* of them have line
+ numbers. find_pc_line handles this. */
+ {
+ struct symtab_and_line tmp_sal;
- if (find_pc_function (stop_func_start) != 0)
- goto step_into_function;
+ tmp_sal = find_pc_line (stop_func_start, 0);
+ if (tmp_sal.line != 0)
+ goto step_into_function;
+ }
step_over_function:
- /* A subroutine call has happened. */
- /* Set a special breakpoint after the return */
- step_resume_break_address =
- ADDR_BITS_REMOVE
- (SAVED_PC_AFTER_CALL (get_current_frame ()));
- step_resume_break_duplicate
- = breakpoint_here_p (step_resume_break_address);
- if (breakpoints_inserted)
- insert_step_breakpoint ();
- goto save_pc;
+ /* A subroutine call has happened. */
+ {
+ /* Set a special breakpoint after the return */
+ struct symtab_and_line sr_sal;
+ sr_sal.pc =
+ ADDR_BITS_REMOVE
+ (SAVED_PC_AFTER_CALL (get_current_frame ()));
+ sr_sal.symtab = NULL;
+ sr_sal.line = 0;
+ step_resume_breakpoint =
+ set_momentary_breakpoint (sr_sal, get_current_frame (),
+ bp_step_resume);
+ step_resume_breakpoint->frame = prev_frame_address;
+ if (breakpoints_inserted)
+ insert_breakpoints ();
+ }
+ goto keep_going;
step_into_function:
- /* Subroutine call with source code we should not step over.
- Do step to the first line of code in it. */
- SKIP_PROLOGUE (stop_func_start);
- sal = find_pc_line (stop_func_start, 0);
- /* Use the step_resume_break to step until
- the end of the prologue, even if that involves jumps
- (as it seems to on the vax under 4.2). */
- /* If the prologue ends in the middle of a source line,
- continue to the end of that source line.
- Otherwise, just go to end of prologue. */
+ /* Subroutine call with source code we should not step over.
+ Do step to the first line of code in it. */
+ SKIP_PROLOGUE (stop_func_start);
+ sal = find_pc_line (stop_func_start, 0);
+ /* Use the step_resume_break to step until
+ the end of the prologue, even if that involves jumps
+ (as it seems to on the vax under 4.2). */
+ /* If the prologue ends in the middle of a source line,
+ continue to the end of that source line (if it is still
+ within the function). Otherwise, just go to end of prologue. */
#ifdef PROLOGUE_FIRSTLINE_OVERLAP
- /* no, don't either. It skips any code that's
- legitimately on the first line. */
+ /* no, don't either. It skips any code that's
+ legitimately on the first line. */
#else
- if (sal.end && sal.pc != stop_func_start)
- stop_func_start = sal.end;
+ if (sal.end && sal.pc != stop_func_start && sal.end < stop_func_end)
+ stop_func_start = sal.end;
#endif
- if (stop_func_start == stop_pc)
- {
- /* We are already there: stop now. */
- stop_step = 1;
- break;
- }
- else
- /* Put the step-breakpoint there and go until there. */
- {
- step_resume_break_address = stop_func_start;
-
- step_resume_break_duplicate
- = breakpoint_here_p (step_resume_break_address);
- if (breakpoints_inserted)
- insert_step_breakpoint ();
- /* Do not specify what the fp should be when we stop
- since on some machines the prologue
- is where the new fp value is established. */
- step_frame_address = 0;
- /* And make sure stepping stops right away then. */
- step_range_end = step_range_start;
- }
- goto save_pc;
+ if (stop_func_start == stop_pc)
+ {
+ /* We are already there: stop now. */
+ stop_step = 1;
+ break;
}
+ else
+ /* Put the step-breakpoint there and go until there. */
+ {
+ struct symtab_and_line sr_sal;
+
+ sr_sal.pc = stop_func_start;
+ sr_sal.symtab = NULL;
+ sr_sal.line = 0;
+ /* Do not specify what the fp should be when we stop
+ since on some machines the prologue
+ is where the new fp value is established. */
+ step_resume_breakpoint =
+ set_momentary_breakpoint (sr_sal, NULL, bp_step_resume);
+ if (breakpoints_inserted)
+ insert_breakpoints ();
- /* We've wandered out of the step range (but haven't done a
- subroutine call or return). */
+ /* And make sure stepping stops right away then. */
+ step_range_end = step_range_start;
+ }
+ goto keep_going;
+ }
- sal = find_pc_line(stop_pc, 0);
-
- if (step_range_end == 1 || /* stepi or nexti */
- sal.line == 0 || /* ...or no line # info */
- (stop_pc == sal.pc /* ...or we're at the start */
- && current_line != sal.line)) { /* of a different line */
- /* Stop because we're done stepping. */
- stop_step = 1;
- break;
- } else {
- /* We aren't done stepping, and we have line number info for $pc.
- Optimize by setting the step_range for the line.
- (We might not be in the original line, but if we entered a
- new line in mid-statement, we continue stepping. This makes
- things like for(;;) statements work better.) */
- step_range_start = sal.pc;
- step_range_end = sal.end;
- goto save_pc;
- }
- /* We never fall through here */
+ /* We've wandered out of the step range. */
+
+ sal = find_pc_line(stop_pc, 0);
+
+ if (step_range_end == 1)
+ {
+ /* It is stepi or nexti. We always want to stop stepping after
+ one instruction. */
+ stop_step = 1;
+ break;
+ }
+
+ if (sal.line == 0)
+ {
+ /* We have no line number information. That means to stop
+ stepping (does this always happen right after one instruction,
+ when we do "s" in a function with no line numbers,
+ or can this happen as a result of a return or longjmp?). */
+ stop_step = 1;
+ break;
}
+ if (stop_pc == sal.pc
+ && (current_line != sal.line || current_symtab != sal.symtab))
+ {
+ /* We are at the start of a different line. So stop. Note that
+ we don't stop if we step into the middle of a different line.
+ That is said to make things like for (;;) statements work
+ better. */
+ stop_step = 1;
+ break;
+ }
+
+ /* We aren't done stepping.
+
+ Optimize by setting the stepping range to the line.
+ (We might not be in the original line, but if we entered a
+ new line in mid-statement, we continue stepping. This makes
+ things like for(;;) statements work better.) */
+
+ if (stop_func_end && sal.end >= stop_func_end)
+ {
+ /* If this is the last line of the function, don't keep stepping
+ (it would probably step us out of the function).
+ This is particularly necessary for a one-line function,
+ in which after skipping the prologue we better stop even though
+ we will be in mid-line. */
+ stop_step = 1;
+ break;
+ }
+ step_range_start = sal.pc;
+ step_range_end = sal.end;
+ goto keep_going;
+
+ check_sigtramp2:
if (trap_expected
&& IN_SIGTRAMP (stop_pc, stop_func_name)
&& !IN_SIGTRAMP (prev_pc, prev_func_name))
us stop), thus stepping into sigtramp.
So we need to set a step_resume_break_address breakpoint
- and continue until we hit it, and then step. */
- step_resume_break_address = prev_pc;
- /* Always 1, I think, but it's probably easier to have
- the step_resume_break as usual rather than trying to
- re-use the breakpoint which is already there. */
- step_resume_break_duplicate =
- breakpoint_here_p (step_resume_break_address);
+ and continue until we hit it, and then step. FIXME: This should
+ be more enduring than a step_resume breakpoint; we should know
+ that we will later need to keep going rather than re-hitting
+ the breakpoint here (see testsuite/gdb.t06/signals.exp where
+ it says "exceedingly difficult"). */
+ struct symtab_and_line sr_sal;
+
+ sr_sal.pc = prev_pc;
+ sr_sal.symtab = NULL;
+ sr_sal.line = 0;
+ /* We perhaps could set the frame if we kept track of what
+ the frame corresponding to prev_pc was. But we don't,
+ so don't. */
+ through_sigtramp_breakpoint =
+ set_momentary_breakpoint (sr_sal, NULL, bp_through_sigtramp);
if (breakpoints_inserted)
- insert_step_breakpoint ();
+ insert_breakpoints ();
+
remove_breakpoints_on_following_step = 1;
another_trap = 1;
}
-/* My apologies to the gods of structured programming. */
-/* Come to this label when you need to resume the inferior. It's really much
- cleaner at this time to do a goto than to try and figure out what the
- if-else chain ought to look like!! */
-
keep_going:
+ /* Come to this label when you need to resume the inferior.
+ It's really much cleaner to do a goto than a maze of if-else
+ conditions. */
-save_pc:
/* Save the pc before execution, to compare with pc after stop. */
prev_pc = read_pc (); /* Might have been DECR_AFTER_BREAK */
prev_func_start = stop_func_start; /* Ok, since if DECR_PC_AFTER
function. */
prev_func_name = stop_func_name;
prev_sp = stop_sp;
+ prev_frame_address = stop_frame_address;
/* If we did not do break;, it means we should keep
running the inferior and not return to debugger. */
- if (trap_expected && stop_signal != SIGTRAP)
+ if (trap_expected && stop_signal != TARGET_SIGNAL_TRAP)
{
/* We took a signal (which we are supposed to pass through to
the inferior, else we'd have done a break above) and we
haven't yet gotten our trap. Simply continue. */
- resume ((step_range_end && !step_resume_break_address)
- || (trap_expected && !step_resume_break_address)
- || bpstat_should_step (),
- stop_signal);
+ resume (CURRENTLY_STEPPING (), stop_signal);
}
else
{
to one-proceed past a breakpoint. */
/* If we've just finished a special step resume and we don't
want to hit a breakpoint, pull em out. */
- if (!step_resume_break_address &&
- remove_breakpoints_on_following_step)
+ if (step_resume_breakpoint == NULL
+ && through_sigtramp_breakpoint == NULL
+ && remove_breakpoints_on_following_step)
{
remove_breakpoints_on_following_step = 0;
remove_breakpoints ();
breakpoints_inserted = 0;
}
else if (!breakpoints_inserted &&
- (step_resume_break_address != 0 || !another_trap))
+ (through_sigtramp_breakpoint != NULL || !another_trap))
{
- insert_step_breakpoint ();
breakpoints_failed = insert_breakpoints ();
if (breakpoints_failed)
break;
trap_expected = another_trap;
- if (stop_signal == SIGTRAP)
- stop_signal = 0;
+ if (stop_signal == TARGET_SIGNAL_TRAP)
+ stop_signal = TARGET_SIGNAL_0;
#ifdef SHIFT_INST_REGS
/* I'm not sure when this following segment applies. I do know, now,
that we shouldn't rewrite the regs when we were stopped by a
random signal from the inferior process. */
+ /* FIXME: Shouldn't this be based on the valid bit of the SXIP?
+ (this is only used on the 88k). */
if (!bpstat_explains_signal (stop_bpstat)
- && (stop_signal != SIGCLD)
+ && (stop_signal != TARGET_SIGNAL_CHLD)
&& !stopped_by_random_signal)
- {
- CORE_ADDR pc_contents = read_register (PC_REGNUM);
- CORE_ADDR npc_contents = read_register (NPC_REGNUM);
- if (pc_contents != npc_contents)
- {
- write_register (NNPC_REGNUM, npc_contents);
- write_register (NPC_REGNUM, pc_contents);
- }
- }
+ SHIFT_INST_REGS();
#endif /* SHIFT_INST_REGS */
- resume ((!step_resume_break_address
- && !handling_longjmp
- && (step_range_end
- || trap_expected))
- || bpstat_should_step (),
- stop_signal);
+ resume (CURRENTLY_STEPPING (), stop_signal);
}
}
prev_func_start = stop_func_start;
prev_func_name = stop_func_name;
prev_sp = stop_sp;
+ prev_frame_address = stop_frame_address;
}
+ do_cleanups (old_cleanups);
}
\f
/* Here to return control to GDB when the inferior stops for real.
/* Make sure that the current_frame's pc is correct. This
is a correction for setting up the frame info before doing
DECR_PC_AFTER_BREAK */
- if (target_has_execution)
+ if (target_has_execution && get_current_frame())
(get_current_frame ())->pc = read_pc ();
if (breakpoints_failed)
The same program may be running in another process.\n");
}
- if (target_has_execution)
- remove_step_breakpoint ();
-
if (target_has_execution && breakpoints_inserted)
if (remove_breakpoints ())
{
target_terminal_ours ();
+ /* Look up the hook_stop and run it if it exists. */
+
+ if (stop_command->hook)
+ {
+ catch_errors (hook_stop_stub, (char *)stop_command->hook,
+ "Error while running hook_stop:\n", RETURN_MASK_ALL);
+ }
+
if (!target_has_stack)
return;
if we have one. */
if (!stop_stack_dummy)
{
- select_frame (get_current_frame (), 0);
-
if (stop_print_frame)
{
int source_only;
POP_FRAME ends with a setting of the current frame, so we
can use that next. */
POP_FRAME;
+ /* Set stop_pc to what it was before we called the function. Can't rely
+ on restore_inferior_status because that only gets called if we don't
+ stop in the called function. */
+ stop_pc = read_pc();
select_frame (get_current_frame (), 0);
}
}
-\f
-static void
-insert_step_breakpoint ()
-{
- if (step_resume_break_address && !step_resume_break_duplicate)
- target_insert_breakpoint (step_resume_break_address,
- step_resume_break_shadow);
-}
-static void
-remove_step_breakpoint ()
+static int
+hook_stop_stub (cmd)
+ char *cmd;
{
- if (step_resume_break_address && !step_resume_break_duplicate)
- target_remove_breakpoint (step_resume_break_address,
- step_resume_break_shadow);
+ execute_user_command ((struct cmd_list_element *)cmd, 0);
+ return (0);
}
\f
int signal_stop_state (signo)
int signo;
{
- return ((signo >= 0 && signo < NSIG) ? signal_stop[signo] : 0);
+ return signal_stop[signo];
}
int signal_print_state (signo)
int signo;
{
- return ((signo >= 0 && signo < NSIG) ? signal_print[signo] : 0);
+ return signal_print[signo];
}
int signal_pass_state (signo)
int signo;
{
- return ((signo >= 0 && signo < NSIG) ? signal_program[signo] : 0);
+ return signal_program[signo];
}
static void
sig_print_header ()
{
- printf_filtered ("Signal\t\tStop\tPrint\tPass to program\tDescription\n");
+ printf_filtered ("\
+Signal Stop\tPrint\tPass to program\tDescription\n");
}
static void
-sig_print_info (number)
- int number;
+sig_print_info (oursig)
+ enum target_signal oursig;
{
- char *name;
-
- if ((name = strsigno (number)) == NULL)
- printf_filtered ("%d\t\t", number);
- else
- printf_filtered ("%s (%d)\t", name, number);
- printf_filtered ("%s\t", signal_stop[number] ? "Yes" : "No");
- printf_filtered ("%s\t", signal_print[number] ? "Yes" : "No");
- printf_filtered ("%s\t\t", signal_program[number] ? "Yes" : "No");
- printf_filtered ("%s\n", safe_strsignal (number));
+ char *name = target_signal_to_name (oursig);
+ printf_filtered ("%s", name);
+ printf_filtered ("%*.*s ", 13 - strlen (name), 13 - strlen (name),
+ " ");
+ printf_filtered ("%s\t", signal_stop[oursig] ? "Yes" : "No");
+ printf_filtered ("%s\t", signal_print[oursig] ? "Yes" : "No");
+ printf_filtered ("%s\t\t", signal_program[oursig] ? "Yes" : "No");
+ printf_filtered ("%s\n", target_signal_to_string (oursig));
}
/* Specify how various signals in the inferior should be handled. */
char *args;
int from_tty;
{
- register char *p = args;
- int signum = 0;
- register int digits, wordlen;
- char *nextarg;
+ char **argv;
+ int digits, wordlen;
+ int sigfirst, signum, siglast;
+ enum target_signal oursig;
+ int allsigs;
+ int nsigs;
+ unsigned char *sigs;
+ struct cleanup *old_chain;
+
+ if (args == NULL)
+ {
+ error_no_arg ("signal to handle");
+ }
- if (!args)
- error_no_arg ("signal to handle");
+ /* Allocate and zero an array of flags for which signals to handle. */
- while (*p)
+ nsigs = (int)TARGET_SIGNAL_LAST;
+ sigs = (unsigned char *) alloca (nsigs);
+ memset (sigs, 0, nsigs);
+
+ /* Break the command line up into args. */
+
+ argv = buildargv (args);
+ if (argv == NULL)
{
- /* Find the end of the next word in the args. */
- for (wordlen = 0;
- p[wordlen] && p[wordlen] != ' ' && p[wordlen] != '\t';
- wordlen++);
- /* Set nextarg to the start of the word after the one we just
- found, and null-terminate this one. */
- if (p[wordlen] == '\0')
- nextarg = p + wordlen;
- else
- {
- p[wordlen] = '\0';
- nextarg = p + wordlen + 1;
- }
-
+ nomem (0);
+ }
+ old_chain = make_cleanup (freeargv, (char *) argv);
- for (digits = 0; p[digits] >= '0' && p[digits] <= '9'; digits++);
+ /* Walk through the args, looking for signal oursigs, signal names, and
+ actions. Signal numbers and signal names may be interspersed with
+ actions, with the actions being performed for all signals cumulatively
+ specified. Signal ranges can be specified as <LOW>-<HIGH>. */
- if (signum == 0)
+ while (*argv != NULL)
+ {
+ wordlen = strlen (*argv);
+ for (digits = 0; isdigit ((*argv)[digits]); digits++) {;}
+ allsigs = 0;
+ sigfirst = siglast = -1;
+
+ if (wordlen >= 1 && !strncmp (*argv, "all", wordlen))
+ {
+ /* Apply action to all signals except those used by the
+ debugger. Silently skip those. */
+ allsigs = 1;
+ sigfirst = 0;
+ siglast = nsigs - 1;
+ }
+ else if (wordlen >= 1 && !strncmp (*argv, "stop", wordlen))
+ {
+ SET_SIGS (nsigs, sigs, signal_stop);
+ SET_SIGS (nsigs, sigs, signal_print);
+ }
+ else if (wordlen >= 1 && !strncmp (*argv, "ignore", wordlen))
+ {
+ UNSET_SIGS (nsigs, sigs, signal_program);
+ }
+ else if (wordlen >= 2 && !strncmp (*argv, "print", wordlen))
+ {
+ SET_SIGS (nsigs, sigs, signal_print);
+ }
+ else if (wordlen >= 2 && !strncmp (*argv, "pass", wordlen))
+ {
+ SET_SIGS (nsigs, sigs, signal_program);
+ }
+ else if (wordlen >= 3 && !strncmp (*argv, "nostop", wordlen))
+ {
+ UNSET_SIGS (nsigs, sigs, signal_stop);
+ }
+ else if (wordlen >= 3 && !strncmp (*argv, "noignore", wordlen))
+ {
+ SET_SIGS (nsigs, sigs, signal_program);
+ }
+ else if (wordlen >= 4 && !strncmp (*argv, "noprint", wordlen))
{
- /* It is the first argument--must be the signal to operate on. */
- if (digits == wordlen)
+ UNSET_SIGS (nsigs, sigs, signal_print);
+ UNSET_SIGS (nsigs, sigs, signal_stop);
+ }
+ else if (wordlen >= 4 && !strncmp (*argv, "nopass", wordlen))
+ {
+ UNSET_SIGS (nsigs, sigs, signal_program);
+ }
+ else if (digits > 0)
+ {
+ /* It is numeric. The numeric signal refers to our own internal
+ signal numbering from target.h, not to host/target signal number.
+ This is a feature; users really should be using symbolic names
+ anyway, and the common ones like SIGHUP, SIGINT, SIGALRM, etc.
+ will work right anyway. */
+
+ sigfirst = siglast = atoi (*argv);
+ if ((*argv)[digits] == '-')
{
- /* Numeric. */
- signum = atoi (p);
- if (signum <= 0 || signum > signo_max ())
- {
- p[wordlen] = '\0';
- error ("Invalid signal %s given as argument to \"handle\".", p);
- }
+ siglast = atoi ((*argv) + digits + 1);
}
- else
+ if (sigfirst > siglast)
{
- /* Symbolic. */
- signum = strtosigno (p);
- if (signum == 0)
- error ("No such signal \"%s\"", p);
+ /* Bet he didn't figure we'd think of this case... */
+ signum = sigfirst;
+ sigfirst = siglast;
+ siglast = signum;
}
-
- if (signum == SIGTRAP || signum == SIGINT)
+ if (sigfirst < 0 || sigfirst >= nsigs)
{
- if (!query ("%s is used by the debugger.\nAre you sure you want to change it? ", strsigno (signum)))
- error ("Not confirmed.");
+ error ("Signal %d not in range 0-%d", sigfirst, nsigs - 1);
+ }
+ if (siglast < 0 || siglast >= nsigs)
+ {
+ error ("Signal %d not in range 0-%d", siglast, nsigs - 1);
}
}
- /* Else, if already got a signal number, look for flag words
- saying what to do for it. */
- else if (!strncmp (p, "stop", wordlen))
- {
- signal_stop[signum] = 1;
- signal_print[signum] = 1;
- }
- else if (wordlen >= 2 && !strncmp (p, "print", wordlen))
- signal_print[signum] = 1;
- else if (wordlen >= 2 && !strncmp (p, "pass", wordlen))
- signal_program[signum] = 1;
- else if (!strncmp (p, "ignore", wordlen))
- signal_program[signum] = 0;
- else if (wordlen >= 3 && !strncmp (p, "nostop", wordlen))
- signal_stop[signum] = 0;
- else if (wordlen >= 4 && !strncmp (p, "noprint", wordlen))
+ else
{
- signal_print[signum] = 0;
- signal_stop[signum] = 0;
+ oursig = target_signal_from_name (*argv);
+ if (oursig != TARGET_SIGNAL_UNKNOWN)
+ {
+ sigfirst = siglast = (int)oursig;
+ }
+ else
+ {
+ /* Not a number and not a recognized flag word => complain. */
+ error ("Unrecognized or ambiguous flag word: \"%s\".", *argv);
+ }
}
- else if (wordlen >= 4 && !strncmp (p, "nopass", wordlen))
- signal_program[signum] = 0;
- else if (wordlen >= 3 && !strncmp (p, "noignore", wordlen))
- signal_program[signum] = 1;
- /* Not a number and not a recognized flag word => complain. */
- else
+
+ /* If any signal numbers or symbol names were found, set flags for
+ which signals to apply actions to. */
+
+ for (signum = sigfirst; signum >= 0 && signum <= siglast; signum++)
{
- error ("Unrecognized or ambiguous flag word: \"%s\".", p);
+ switch ((enum target_signal)signum)
+ {
+ case TARGET_SIGNAL_TRAP:
+ case TARGET_SIGNAL_INT:
+ if (!allsigs && !sigs[signum])
+ {
+ if (query ("%s is used by the debugger.\n\
+Are you sure you want to change it? ",
+ target_signal_to_name
+ ((enum target_signal)signum)))
+ {
+ sigs[signum] = 1;
+ }
+ else
+ {
+ printf_unfiltered ("Not confirmed, unchanged.\n");
+ gdb_flush (gdb_stdout);
+ }
+ }
+ break;
+ default:
+ sigs[signum] = 1;
+ break;
+ }
}
- /* Find start of next word. */
- p = nextarg;
- while (*p == ' ' || *p == '\t') p++;
+ argv++;
}
- NOTICE_SIGNAL_HANDLING_CHANGE;
+ target_notice_signals(inferior_pid);
if (from_tty)
{
/* Show the results. */
sig_print_header ();
- sig_print_info (signum);
+ for (signum = 0; signum < nsigs; signum++)
+ {
+ if (sigs[signum])
+ {
+ sig_print_info (signum);
+ }
+ }
}
+
+ do_cleanups (old_chain);
}
-/* Print current contents of the tables set by the handle command. */
+/* Print current contents of the tables set by the handle command.
+ It is possible we should just be printing signals actually used
+ by the current target (but for things to work right when switching
+ targets, all signals should be in the signal tables). */
static void
signals_info (signum_exp, from_tty)
char *signum_exp;
int from_tty;
{
- register int i;
+ enum target_signal oursig;
sig_print_header ();
if (signum_exp)
{
/* First see if this is a symbol name. */
- i = strtosigno (signum_exp);
- if (i == 0)
+ oursig = target_signal_from_name (signum_exp);
+ if (oursig == TARGET_SIGNAL_UNKNOWN)
{
/* Nope, maybe it's an address which evaluates to a signal
number. */
- i = parse_and_eval_address (signum_exp);
- if (i >= NSIG || i < 0)
+ /* The numeric signal refers to our own internal
+ signal numbering from target.h, not to host/target signal number.
+ This is a feature; users really should be using symbolic names
+ anyway, and the common ones like SIGHUP, SIGINT, SIGALRM, etc.
+ will work right anyway. */
+ int i = parse_and_eval_address (signum_exp);
+ if (i >= (int)TARGET_SIGNAL_LAST
+ || i < 0
+ || i == (int)TARGET_SIGNAL_UNKNOWN
+ || i == (int)TARGET_SIGNAL_DEFAULT)
error ("Signal number out of bounds.");
+ oursig = (enum target_signal)i;
}
- sig_print_info (i);
+ sig_print_info (oursig);
return;
}
printf_filtered ("\n");
- for (i = 0; i < NSIG; i++)
+ /* These ugly casts brought to you by the native VAX compiler. */
+ for (oursig = TARGET_SIGNAL_FIRST;
+ (int)oursig < (int)TARGET_SIGNAL_LAST;
+ oursig = (enum target_signal)((int)oursig + 1))
{
QUIT;
- sig_print_info (i);
+ if (oursig != TARGET_SIGNAL_UNKNOWN
+ && oursig != TARGET_SIGNAL_DEFAULT
+ && oursig != TARGET_SIGNAL_0)
+ sig_print_info (oursig);
}
printf_filtered ("\nUse the \"handle\" command to change these tables.\n");
struct inferior_status *inf_status;
int restore_stack_info;
{
- inf_status->pc_changed = pc_changed;
inf_status->stop_signal = stop_signal;
inf_status->stop_pc = stop_pc;
inf_status->stop_frame_address = stop_frame_address;
inf_status->step_range_end = step_range_end;
inf_status->step_frame_address = step_frame_address;
inf_status->step_over_calls = step_over_calls;
- inf_status->step_resume_break_address = step_resume_break_address;
inf_status->stop_after_trap = stop_after_trap;
inf_status->stop_soon_quietly = stop_soon_quietly;
/* Save original bpstat chain here; replace it with copy of chain.
inf_status->restore_stack_info = restore_stack_info;
inf_status->proceed_to_finish = proceed_to_finish;
- bcopy (stop_registers, inf_status->stop_registers, REGISTER_BYTES);
-
+ memcpy (inf_status->stop_registers, stop_registers, REGISTER_BYTES);
+
+ read_register_bytes (0, inf_status->registers, REGISTER_BYTES);
+
record_selected_frame (&(inf_status->selected_frame_address),
&(inf_status->selected_level));
return;
}
+struct restore_selected_frame_args {
+ FRAME_ADDR frame_address;
+ int level;
+};
+
+static int restore_selected_frame PARAMS ((char *));
+
+/* Restore the selected frame. args is really a struct
+ restore_selected_frame_args * (declared as char * for catch_errors)
+ telling us what frame to restore. Returns 1 for success, or 0 for
+ failure. An error message will have been printed on error. */
+static int
+restore_selected_frame (args)
+ char *args;
+{
+ struct restore_selected_frame_args *fr =
+ (struct restore_selected_frame_args *) args;
+ FRAME fid;
+ int level = fr->level;
+
+ fid = find_relative_frame (get_current_frame (), &level);
+
+ /* If inf_status->selected_frame_address is NULL, there was no
+ previously selected frame. */
+ if (fid == 0 ||
+ FRAME_FP (fid) != fr->frame_address ||
+ level != 0)
+ {
+ warning ("Unable to restore previously selected frame.\n");
+ return 0;
+ }
+ select_frame (fid, fr->level);
+ return(1);
+}
+
void
restore_inferior_status (inf_status)
struct inferior_status *inf_status;
{
- FRAME fid;
- int level = inf_status->selected_level;
-
- pc_changed = inf_status->pc_changed;
stop_signal = inf_status->stop_signal;
stop_pc = inf_status->stop_pc;
stop_frame_address = inf_status->stop_frame_address;
step_range_end = inf_status->step_range_end;
step_frame_address = inf_status->step_frame_address;
step_over_calls = inf_status->step_over_calls;
- step_resume_break_address = inf_status->step_resume_break_address;
stop_after_trap = inf_status->stop_after_trap;
stop_soon_quietly = inf_status->stop_soon_quietly;
bpstat_clear (&stop_bpstat);
breakpoint_proceeded = inf_status->breakpoint_proceeded;
proceed_to_finish = inf_status->proceed_to_finish;
- bcopy (inf_status->stop_registers, stop_registers, REGISTER_BYTES);
+ memcpy (stop_registers, inf_status->stop_registers, REGISTER_BYTES);
+
+ /* The inferior can be gone if the user types "print exit(0)"
+ (and perhaps other times). */
+ if (target_has_execution)
+ write_register_bytes (0, inf_status->registers, REGISTER_BYTES);
/* The inferior can be gone if the user types "print exit(0)"
(and perhaps other times). */
+
+ /* FIXME: If we are being called after stopping in a function which
+ is called from gdb, we should not be trying to restore the
+ selected frame; it just prints a spurious error message (The
+ message is useful, however, in detecting bugs in gdb (like if gdb
+ clobbers the stack)). In fact, should we be restoring the
+ inferior status at all in that case? . */
+
if (target_has_stack && inf_status->restore_stack_info)
{
- fid = find_relative_frame (get_current_frame (),
- &level);
-
- /* If inf_status->selected_frame_address is NULL, there was no
- previously selected frame. */
- if (fid == 0 ||
- FRAME_FP (fid) != inf_status->selected_frame_address ||
- level != 0)
- {
-#if 1
- /* I'm not sure this error message is a good idea. I have
- only seen it occur after "Can't continue previously
- requested operation" (we get called from do_cleanups), in
- which case it just adds insult to injury (one confusing
- error message after another. Besides which, does the
- user really care if we can't restore the previously
- selected frame? */
- fprintf (stderr, "Unable to restore previously selected frame.\n");
-#endif
- select_frame (get_current_frame (), 0);
- return;
- }
-
- select_frame (fid, inf_status->selected_level);
+ struct restore_selected_frame_args fr;
+ fr.level = inf_status->selected_level;
+ fr.frame_address = inf_status->selected_frame_address;
+ /* The point of catch_errors is that if the stack is clobbered,
+ walking the stack might encounter a garbage pointer and error()
+ trying to dereference it. */
+ if (catch_errors (restore_selected_frame, &fr,
+ "Unable to restore previously selected frame:\n",
+ RETURN_MASK_ERROR) == 0)
+ /* Error in restoring the selected frame. Select the innermost
+ frame. */
+ select_frame (get_current_frame (), 0);
}
}
add_info ("signals", signals_info,
"What debugger does when program gets various signals.\n\
Specify a signal number as argument to print info on that signal only.");
+ add_info_alias ("handle", "signals", 0);
add_com ("handle", class_run, handle_command,
"Specify how to handle a signal.\n\
-Args are signal number followed by flags.\n\
-Flags allowed are \"stop\", \"print\", \"pass\",\n\
- \"nostop\", \"noprint\" or \"nopass\".\n\
-Print means print a message if this signal happens.\n\
+Args are signal numbers and actions to apply to those signals.\n\
+Signal numbers may be numeric (ex. 11) or symbolic (ex. SIGSEGV).\n\
+Numeric ranges may be specified with the form LOW-HIGH (ex. 14-21).\n\
+The special arg \"all\" is recognized to mean all signals except those\n\
+used by the debugger, typically SIGTRAP and SIGINT.\n\
+Recognized actions include \"stop\", \"nostop\", \"print\", \"noprint\",\n\
+\"pass\", \"nopass\", \"ignore\", or \"noignore\".\n\
Stop means reenter debugger if this signal happens (implies print).\n\
+Print means print a message if this signal happens.\n\
Pass means let program see this signal; otherwise program doesn't know.\n\
+Ignore is a synonym for nopass and noignore is a synonym for pass.\n\
Pass and Stop may be combined.");
- numsigs = signo_max () + 1;
- signal_stop = xmalloc (sizeof (signal_stop[0]) * numsigs);
- signal_print = xmalloc (sizeof (signal_print[0]) * numsigs);
- signal_program = xmalloc (sizeof (signal_program[0]) * numsigs);
+ stop_command = add_cmd ("stop", class_obscure, not_just_help_class_command,
+ "There is no `stop' command, but you can set a hook on `stop'.\n\
+This allows you to set a list of commands to be run each time execution\n\
+of the program stops.", &cmdlist);
+
+ numsigs = (int)TARGET_SIGNAL_LAST;
+ signal_stop = (unsigned char *)
+ xmalloc (sizeof (signal_stop[0]) * numsigs);
+ signal_print = (unsigned char *)
+ xmalloc (sizeof (signal_print[0]) * numsigs);
+ signal_program = (unsigned char *)
+ xmalloc (sizeof (signal_program[0]) * numsigs);
for (i = 0; i < numsigs; i++)
{
signal_stop[i] = 1;
/* Signals caused by debugger's own actions
should not be given to the program afterwards. */
- signal_program[SIGTRAP] = 0;
- signal_program[SIGINT] = 0;
+ signal_program[TARGET_SIGNAL_TRAP] = 0;
+ signal_program[TARGET_SIGNAL_INT] = 0;
/* Signals that are not errors should not normally enter the debugger. */
-#ifdef SIGALRM
- signal_stop[SIGALRM] = 0;
- signal_print[SIGALRM] = 0;
-#endif /* SIGALRM */
-#ifdef SIGVTALRM
- signal_stop[SIGVTALRM] = 0;
- signal_print[SIGVTALRM] = 0;
-#endif /* SIGVTALRM */
-#ifdef SIGPROF
- signal_stop[SIGPROF] = 0;
- signal_print[SIGPROF] = 0;
-#endif /* SIGPROF */
-#ifdef SIGCHLD
- signal_stop[SIGCHLD] = 0;
- signal_print[SIGCHLD] = 0;
-#endif /* SIGCHLD */
-#ifdef SIGCLD
- signal_stop[SIGCLD] = 0;
- signal_print[SIGCLD] = 0;
-#endif /* SIGCLD */
-#ifdef SIGIO
- signal_stop[SIGIO] = 0;
- signal_print[SIGIO] = 0;
-#endif /* SIGIO */
-#ifdef SIGURG
- signal_stop[SIGURG] = 0;
- signal_print[SIGURG] = 0;
-#endif /* SIGURG */
+ signal_stop[TARGET_SIGNAL_ALRM] = 0;
+ signal_print[TARGET_SIGNAL_ALRM] = 0;
+ signal_stop[TARGET_SIGNAL_VTALRM] = 0;
+ signal_print[TARGET_SIGNAL_VTALRM] = 0;
+ signal_stop[TARGET_SIGNAL_PROF] = 0;
+ signal_print[TARGET_SIGNAL_PROF] = 0;
+ signal_stop[TARGET_SIGNAL_CHLD] = 0;
+ signal_print[TARGET_SIGNAL_CHLD] = 0;
+ signal_stop[TARGET_SIGNAL_IO] = 0;
+ signal_print[TARGET_SIGNAL_IO] = 0;
+ signal_stop[TARGET_SIGNAL_POLL] = 0;
+ signal_print[TARGET_SIGNAL_POLL] = 0;
+ signal_stop[TARGET_SIGNAL_URG] = 0;
+ signal_print[TARGET_SIGNAL_URG] = 0;
}
projects / binutils.git / blobdiff