* gas/hppa/reloc/reloc.exp (reloc_reduce): Correct offsets at

[binutils.git] / gas / ChangeLog

Mon Nov  1 21:37:04 1993  Jeffrey A. Law  ([email protected])

	* config/tc-hppa.c (process_exit): Create temporary symbols with
	correct prefixes so they can be eliminated later.

	* config/tc-hppa.c (call_info struct): Delete unused "frame" field.
	(pa_callinfo): Insert framesize into the unwind information as 
	soon as it's available.
	(pa_build_unwind_subspace): Do not insert framesize into the unwind
	information here.

	* Add support for marker type relocations.  These mark areas
	of interest to the linker.  ENTRY/EXIT relocations for SOM are
	an example of marker relocations.
	* write.c (write_relocs): Instead of assuming size of a relocation
	is 4 bytes, pick up the size from relocation itself.
	(fixup_segment): Do not complain that a value is too small for 
	marker relocations.

	* struc-symbol.h: Add new "sy_used" field to the symbol structure.
	* expr.c (operand): Set sy_used for any symbol used as an operand.
	(expr): Likewise for any symbol used in an expression.
	* config/tc-hppa.h (tc_frob_symbol): Define.  Punt imported
	symbols which are never used and absolute symbols which local scope.

	* config/obj-som.h (obj_frob_file): Define.
	* config/obj-som.c (obj_som_init_stab_section): Set alignment
	of stab sections.  Make space for the special stab entry.
	(adjust_stab_sections): Adjust the special entry in the 
	stabs section.
	(som_frob_file): New function.  Simply calls adjust_stab_sections
	for each section.

Mon Nov  1 17:54:29 1993  Ian Lance Taylor  ([email protected])

	* config/tc-mips.c (PIC_CALL_REG, SP, FP): Define.
	(mips_pic, mips_cprestore_offset): New static variables.
	(md_pseudo_table): Handle .abicalls, .cpload, and .cprestore.
	Ignore .bgnb and .endb.
	(gp_reference): _gp_disp is never addressed off GP.
	(macro_build): Ignore macros while searching for insn.  For cases
	i, j, and o, accept the reloc type as an argument rather than
	assuming BFD_RELOC_LO16.  Don't try to convert BFD_RELOC_LO16 to
	BFD_RELOC_MIPS_GPREL.  Added new case a.
	(set_at, load_register, macro): Changed calls to macro_build to
	pass new argument for i, j and o cases.
	(macro): Handle M_JAL_1, M_JAL_2 and M_JAL_A.  These require
	special handling when generating SVR4 PIC code.
	(mips_ip, tc_get_register, s_frame): Use macros FP, SP, GP and AT
	rather than hard coded constants.
	(md_apply_fix): Handle BFD_RELOC_MIPS_LITERAL and
	BFD_RELOC_MIPS_CALL16.
	(s_option): Set mips_pic based on .option picN.
	(s_abicalls): New function; set mips_pic to 2.
	(s_cpload): New function; handle .cpload.
	(s_cprestore): New function; handle .cprestore.

	* config/obj-ecoff.c (obj_pseudo_table): Add entries for .bgnb,
	.endb and .verstamp, setting them to s_ignore.

Sun Oct 31 00:36:40 1993  Jeffrey A. Law  ([email protected])

	* config/tc-hppa.c (subspace_dictionary_chain): Add new ssd_defined
	field.  Define SUBSPACE_DEFINED accessor macro.
	(pa_subspace): Allow user to override subspace attributes for
	built-in subspaces.  Set ssd_defined at the end of fcn -- that
	way the attributes can only be changed once.  Pass newly allocated
	name to is_defined_subspace, not a pointer to the input line.
	Fix typo in space/subspace rework.
	(is_defined_subspace): Delete unused 2nd arg.  All callers changed.

	* config/tc-hppa.c (pa_import): If currently in the text segment
	and a symbol is imported without type information, set BSF_FUNCTION
	for the symbol.
	* write.c (relax_and_size_seg): Correct test to determine if
	the section's size was rounded up.

	* config/obj-som.h (obj_set_symbol_type): Define a hook so GAS
	can properly set all the SOM symbol types.
	* config/tc-hppa.c (pa_symbol_type): New enum to represent the 
	symbol types which can be set from an IMPORT/EXPORT statement.
	(pa_export_args): Set the pa_symbol_type type based on arguments.
	If defined, call obj_set_symbol_type to pass this information on
	to the BFD backend.

	* read.c (get_stab_string_offset): Set SEC_DEBUGGING for any 
	stab section we make.
	(s_stab_generic): Likewise.

Sat Oct 30 14:26:20 1993  Jeffrey A. Law  ([email protected])

	* Allow backends to override the value of the fake label.
	* write.h (LOCAL_LABEL): Delete DOT_LABEL_PREFIX code.  Instead
	assume backends will define LOCAL_LABEL if anything other than
	'L' is used to denote a local label.
	(FAKE_LABEL_NAME): New macro.  Defines the default name used for
	the "fake" label.
	* expr.c (make_expr_symbol): Delete DOT_LABEL_PREFIX code
	and instead simply use the string defined by FAKE_LABEL_NAME.
	(operand): Likewise.
	* read.c (s_stab_generic): Likewise.
	* config/tc-hppa.h (FAKE_LABEL_NAME): Define as L$0\001 so it's
	known to be a local label.
	* config/tc-i386.h (DOT_LABEL_PREFIX): Delete.
	(LOCAL_LABEL, FAKE_LABEL_NAME): Define.
	* config/tc-m68k.h (DOT_LABEL_PREFIX): Delete.
	(LOCAL_LABEL, FAKE_LABEL_NAME): Define.
	* config/te-sco386.h (DOT_LABEL_PREFIX): Delete.
	(LOCAL_LABEL, FAKE_LABEL_NAME): Define.

	Rework space/subspace handling in PA code to fully support
	SOM spaces/subspaces.
	* config/tc-hppa.c (USE_ALIASES): New object-format dependent define
	to control the use of space/subspace name aliases.
	(update_subspace): Accept space chain entry for containing space
	as a new parameter.  All callers changed.
	(pa_get_label): Use current_space rather than pa_segment_to_space.
	(pa_define_label): Likewise.
	(pa_undefine_label): Likewise.
	(md_begin): Change into the (possibly modified) text_section.
	(pa_parse_space_stmt): Create a new segment/space if create_flag
	is true, and the space name is not one of the two predefined spaces.
	(pa_subspace): Use current_space rather than a lookup via 
	pa_segment_to_space.  Reset BFD section flags as required by 
	the .subspace directive.  Likewise for the section alignment.
	Pass the current space to update_subspace and create_new_subspace.
	(pa_spaces_begin): Only use space/subspace aliases if USE_ALIASES
	is true.  When not using aliases, create a BFD section for each
	subspace encountered.  When not using aliases replace the default
	text, data, and bss segments with new ones.
	(create_new_subspace): When not using aliases each subspace has a 
	section/segment and subsegments are not needed, so set the subsegment
	to zero. 

	* config/tc-hppa.c (pa_parse_space_stmt): If needed, call
	obj_set_section_attributes to pass space attributes to the 
	BFD backend.
	(create_new_space): Likewise.
	(create_new_subspace): Likewise for subspace attributes using 
	obj_set_subsection_attributes.
	(update_subspace): Likewise for subspace attributes using
	obj_set_subsection_attributes.

	* config/tc-hppa.c (pa_parse_space_stmt): Get segment and sort key
	for $TEXT$ and $PRIVATE$ from the default space structure.

	* config/tc-hppa.c (pa_export_args): Always set BSF_FUNCTION
	as appropriate for the given type.

	* config/tc-hppa.c (tc_gen_reloc): Preliminary stab at handling
	SOM relocations.

	* config/tc-hppa.c (pa_comm): Delete incorrect check for symbol
	redefinition.

	* config/obj-som.[ch]: New files for SOM support.  Note SOM
	support is not yet complete in GAS or BFD.

	* config/ho-hppabsd.h:  Delete IO* macros, they are defined in 
	stdio.h.  Delete declaration of free.  Include stdlib.h, unistd.h,
	and string.h.

Fri Oct 29 13:26:12 1993  Jeffrey A. Law  ([email protected])

	* Allow backends to override the section names used for embedded
	stabs support.  Needed for SOM.
	* read.c (STAB_SECTION_NAME): Default the name of the stab section
	to ".stab".  
	(STAB_STRING_SECTION_NAME): Likewise for the stab strings section.
	(get_stab_string_offset): Is now passed the full name for the
	stab string section rather than a name prefix.  All references
	changed.
	(s_stab_generic): New argument for the stab string section name.
	all references changed.
	(s_xstab): Append "str" to the stab section name to get the
	stab string section name.
	* config/obj-coffbfd.c (obj_coff_init_stab_section): Append "str"
	to stab section name to get the stab string section name.  Pass
	the full name of the stab string section to get_stab_string_offset.
	* config/obj-elf.c (obj_elf_init_stab_section): Likewise.
	
	* config/tc-hppa.c (md_begin): Disable "-R" option to fold
	textand data segments.  Warn user "-R" is unsupported on the
	PA.

Thu Oct 28 12:36:13 1993  Jeffrey A. Law  ([email protected])

	* config/tc-hppa.c (md_pseudo_table): Default alignment is 8 for
	.align and .ALIGN directives.

	* config/tc-hppa.c (pa_space): Do not report an error for a .space
	directive which does not define a "well-known" space and does
	not include a space number as an argument.
	
	* config/tc-hppa.c (pa_def_subspaces): Correct initialization of the
	"defined", "loadable", "code_only" and "space_index" fields.
	(pa_def_spaces): Correct initialization of the "spnum", "defined",
	and "private" fields.

	* write.h (struct fix): Add new tc_fix_data field for the various
	backends to attach machine dependent fixup information to.
	* write.c (fix_new_internal): Initialize new tc_fix_data field.
	* config/tc-hppa.c (hppa_fix_struct): Delete unnecessary fix_fixP and
	fx_next fields.
	(hppa_find_hppa_fix): Delete unnecessary function.  Fix all
	callers	to get HPPA fixup information from the tc_fix_data field
	in the GAS fixup.
	(hppa_fix_root): Delete unnecessary variable.
	(fix_new_hppa): Attach HPPA fixup data to the GAS fixup.

	* config/tc-hppa.c (pa_set_start_symbol); Delete unwanted
	function.  Fix all callers.
	(subspace_dictionary_chain): Delete unused ssd_start_sym field.

	* config/tc-hppa.c (hppa_fix_adjustable): New function to determine
	if a particular fixup is adjustable.
	* config/tc-hppa.h (tc_fix_adjustable): Call hppa_fix_adjustable to
	perform the real work.

	* config/tc-hppa.h (RELOC_EXPANSION_POSSIBLE): Move definition out
	of OBJ_XXX conditionals.
	(MAX_RELOC_EXPANSION): Likewise.

	* config/tc-hppa.c (log2): Renamed from is_power_of_2.  Fix all
	callers. Now returns log2 (N) for positive N which are an exact
	power of two or -1 for an error.

	* config/tc-hppa.c (pa_callinfo): Range check values provided for 
	ENTRY_GR, ENTRY_FR and ENTRY_SR.  Properly adjust vaues before
	inserting them into the unwind table.

	* config/tc-hppa.c (NEEDS_FIXUP): Delete definition and all references.
	(hppa_gen_reloc_type): New object format dependent macro.
	(pa_ip): Delete tons of code which was either OBJ_SOM or OBJ_ELF
	conditional.  The code can (and will) be shared between SOM & ELF
	formats in the near future.
	(cons_fix_new_hppa, md_apply_fix_1): Likewise.
	(pa_build_unwind_subspace, process_exit, pa_exit): Likewise.
	(tc_gen_reloc): Use hppa_gen_reloc rather than an object format
	specific call.

	* config/tc-hppa.c (pa_comm): Set the segment for a common symbol
	to bfd_und_section.

	* config/obj-elf.h (obj_elf_version): Add extern prototype.

	* configure.in (hppa-*-bsd*): New configuration.
	BFD is always used for GAS generating SOM objects.

	* write.c (adjust_reloc_syms): Set sy_used_in_reloc if an
	adjustment is rejected by the target machine.

	* config/tc-hppa.c (pa_big_cons): Delete function and its
	declaration.  All callers changed to use pa_cons.

	* write.c (fixup_segment): Fix indention and open/close brace
	problem.

	From Pete Hoogenboom:
	* config/tc-hppa.c (md_atof): Return a NULL on success rather than
	an empty string.

	* config/tc-hppa.c (pa_parse_space_stmt): Advance
	input_line_poitner when an invalid argument is encountered.

Thu Oct 28 13:09:26 1993  Ian Lance Taylor  ([email protected])

	* config/tc-a29k.c (md_begin): When opcodes are mashed together in
	the table, require that the one without bit 0x1000000 set come
	first.  Require further that it be case 'b' or 'P'.  The a29k
	opcode table already meets these constraints.
	(machine_ip): When handling case 'i' or 'A', make sure that the
	appropriate opcode really exists by looking at the next entry in
	the opcode table.

Wed Oct 27 11:48:56 1993  Ian Lance Taylor  ([email protected])

	* config/tc-m68k.c (m68k_ip): Adjust offsets for PC relative
	fixups.  Add 6 for long 7.3 case, 2 for short 7.2 case.

	* config/obj-ecoff.c (obj_ecoff_ent): Ignore an optional number
	after a .ent directive.

	* config/tc-mips.c (mips_ip): Handle '>' case (shift amount
	between 32 and 63 for double shift instruction).  Do & 0x1f rather
	than % 32.
	(printInsn): Handle '>'.

Tue Oct 26 16:58:36 1993  Ian Lance Taylor  ([email protected])

	* config/tc-ns32k.c (tc_aout_fix_to_chars): Output the symbol
	number in the right place.  Untested.  Probably does not work for
	cross assembly.  From [email protected] (Andrew Cagney).

	* config/tc-m68k.c (md_apply_fix_2): Error if a short branch uses
	an illegal offset of 0 or -1.

	* config/obj-elf.c (obj_elf_init_stab_section): Align .stab
	section to a longword boundary.

Tue Oct 26 10:24:31 1993  Ken Raeburn  ([email protected])

	* Makefile.in (CHECKFLAGS): Pass down RUNTESTFLAGS.

	From Jeff Law:
	* config/tc-hppa.c (tc_gen_reloc): ELF32_HPPA_R_ADDEND ->
	HPPA_R_ADDEND.

Mon Oct 25 11:17:58 1993  Steve Chamberlain  ([email protected])

	* config/tc-sh.c (build_Mbytes): Write the relocs to the correct
	address. (md_assemble): Make error handling a bit more graceful.
	(md_apply_fix):  Don't warn on non aligned displacement.
	
	* config/tc-z8k.c (get_specific, built_bytes):  Understand all the
	aspects of lda.

Mon Oct 25 10:20:31 1993  Ken Raeburn  ([email protected])

	* doc/Makefile.in (install-info): Use "$<*" so VPATH will find
	as.info* even if they're in $(srcdir) (e.g., for FSF
	distributions).

	* write.c (write_relocs): For relocs that are pc_relative and
	pcrel_offset and not partial_inplace, adjust reloc->addend to
	compensate for a bfd_perform_relocation bug.

	* config/tc-sparc.h: Removed remaining non-BFD_ASSEMBLER code.
	* config/tc-sparc.c: Ditto.
	(tc_gen_reloc): Include fx_offset for pcrel fixups.

Sun Oct 24 16:49:00 1993  Jim Wilson  ([email protected])

	* tc-mips.c (md_pseudo_table): Add dword pseudo op.

Fri Oct 22 20:40:56 1993  david d `zoo' zuhn  ([email protected])

	* messages.c: replaced all variables called Format with 'format',
	  for consistency throughout

	* configure.in: handle mips*- instead of mips, mips*el for little
	endian configurations

Fri Oct 22 14:45:49 1993  Ian Lance Taylor  ([email protected])

	* input-scrub.c (physical_input_file, logical_input_file,
	physical_input_line, logical_input_line): Made static.
	(as_where): Return current file name and line number, don't print
	them out.
	* messages.c (as_show_where): New static function.  Other
	functions use it instead of as_where.
	(as_bad_internal): New static function.
	(as_bad): Use as_bad_internal.
	(as_bad_where): New function, like as_bad but taking a file name
	and line number.
	* as.h (as_bad_where): Declare.
	(as_where): Change prototype for new arguments.
	* write.h (fixS): Added fields fx_file and fx_line.
	* write.c (fix_new_internal): Save file and line number in fix.
	(fixup_segment): Use as_bad_where, not as_bad.
	* input-file.c (f_in, file_name): Made static.
	* cond.c (struct file_line): Just use file and line fields.
	(s_else): Use as_where and as_bad_where, not get_file_line and
	set_file_line.
	(get_file_line, set_file_line): Removed.
	* listing.c (listing_newline): Use as_where.
	* config/obj-coffbfd.c (obj_coff_init_stab_section): Use as_where.
	* config/obj-ecoff.c (add_file): Use as_where.
	* config/obj-elf.c (obj_elf_init_stab_section): Use as_where.
	* config/tc-m68k.c (md_apply_fix_2): Use as_bad_where.
	* config/tc-mips.c (tc_gen_reloc): Use as_bad_where, not assert.

Thu Oct 21 12:52:01 1993  Ken Raeburn  ([email protected])

	* config/tc-m68k.h: Don't define REGISTER_PREFIX or
	OPTIONAL_REGISTER_PREFIX if either is already defined.

	* config/tc-m68k.c (m68k_ip): Delete some code in "#if 0".

	* configure.in: Set bfd_gas for all sparc targets.  Added facility
	for keeping or rejecting configurations still under development;
	default is to assume production environment, and reject configs
	still being worked on.  Mark Elf configurations (except sparc and
	i386) as developmental.  Deleted cases matching some generic names
	in favor of more specific names.  (E.g., when we get Alpha
	support, we'll still only support VMS for Vax.)

	* config/tc-sparc.h (md_end): New macro.
	* config/tc-sparc.c (md_end): Function deleted.
	(BFD_RELOC_*): Delete macros that used to help keep the non-bfd
	version compiling.  All sparc targets will use bfd now.
	* tc.h (md_end): Don't declare if it's defined as a macro.

	Changes from Jeff Law and Peter Hoogenboom:

	* read.c (next_char_of_string): Limit octal character constants to
	three digits.

	* config/tc-hppa.h: Major cleanup.  Use GNU-style comments.  Warn
	against placing additional object-file dependent code here.  Warn
	against contaminating all of GAS with the internals of tc-hppa.c
	through inclusion of tc-hppa.h.  Delete all forward declarations
	for functions only used within tc-hppa.c, likewise for structures,
	variables, and #defines.  Try to group OBJ_ELF and OBJ_SOM
	conditional code in a few small places.

	* config/tc-hppa.c: Major cleanup.  Use GNU-style comments.  Group
	structures, global variables, forward declarations together.
	Reduce (or in some cases eliminate) OBJ_ELF and OBJ_SOM
	conditional code -- try to group conditional code together
	into a few places.   Make all functions and variables which
	are only used within tc-hppa.c static.  PARAMize all functions.
	Add comments to functions.  Delete unused functions, variables,
	#defines, etc.  Delete unused members within structures.  Delete
	ldil;ble hacks -- it is believed they were installed to work
	around old gas bugs.   Avoid using mixed case for local
	functions, variables, and structures.  Fix formatting problems
	not found by GNU-indent.  Add FIXME notices for things which
	should be worked on the near future.  Delete lots of old
	useless (1.36 PA-SOM) code.  

	* config/tc-hppa.c: (fix_new_hppa): Initialize the fx_r_type
	field of the fixS structure.  Needed to build unwind
	descriptors correctly.

	* write.c: (fixup_segment): Allow expressions such as
	sym1-sym2+const as long as sym2 is $global$.

	* write.c (adjust_reloc_syms): Provide a hook so that a target
	cpu configuration can reject certain relocation reductions.
	* tc-hppa.h (tc_fix_adjustable): New macro.  Only accept relocations
	which do not involve function symbols.

	* config/tc-hppa.h: Reindent with GNU-indent.  Delete references
	to OBJ_OSFROSE.  Fix typos (OBJ_SOME -> OBJ_SOM).  Delete unused
	STAB_FIXUP macro.
	* config/tc-hppa.c: Likewise.

	* config/tc-hppa.c (md_apply_fix_1): Use elf_symbol_type, instead
	of elf32_symbol_type.
	(pa_export_args): Likewise.
	(elf_hppa_final_processing): Likewise.
	(pa_desc): Do not call obj_elf_desc.  (Is pa_desc even needed
	anymore?)
	(hppa_tc_make_sections): Do not declare elf_get_symtab_map any
	ore.

	* config/tc-hppa.c: (md_section_align): Align all sections to
	a multiple of the section alignment rather than always a
	multiple of 8.

	* config/tc-hppa.c (hppa_tc_symbol): If the argument relocation
	bits are zero (eg they specify no relocations), then do not even
	bother adding their entries to thesymextn section.

Thu Oct 21 15:44:55 1993  Ian Lance Taylor  ([email protected])

	* config/tc-sparc.c (md_parse_option): Accept and ignore -sparc
	option, which is used by the SunOS make default .s.o rule.

Tue Oct 19 18:13:26 1993  Ian Lance Taylor  ([email protected])

	* config/tc-m68k.h (AOUT_MACHTYPE): Define to be external variable
	m68k_aout_machtype.
	* config/tc-m68k.c (omagic): Remove obsolete and unused variable.
	(m68k_aout_machtype): New variable, if OBJ_AOUT.
	(md_assemble): Initialize m68k_aout_machtype based on
	current_architecture, if OBJ_AOUT.
	(md_parse_option): Remove obsolete reference to omagic.

Thu Oct 14 16:51:00 1993  Ian Lance Taylor  ([email protected])

	* config/tc-mips.c (md_pseudo_table): Ignore .livereg pseudo-op.
	(s_option): Ignore .option O* and .option pic*.
	(s_ent): Skip whitespace between symbol and optional digit.
	(my_getSmallExpression): Handle ($xx) correctly: assume 0($xx).

	* app.c (do_scrub_next_char): Always accept 'x' and 'X' as escape
	characters in state 6.
	* read.c (next_char_of_string): Accept \Xh* and \xh* where h* are
	hexidecimal digits.

	* config/tc-i386.c (md_apply_fix_1): Make cross segment calls work
	for ELF by hacking around bizarre bfd_perform_relocation behaviour
	that I don't dare change.

Thu Oct 14 11:33:25 1993  Michael Meissner  ([email protected])

	* config/tc-i386.c: (md_begin): Do not zero static arrays.  Don't
	call strchr for each character to see if it is a special char,
	instead add a second loop over special_chars.  Set alignment
	of text, data and bss sections to 4.
	(pi, te, pt, pe, ps): Add declarations so that DEBUG386 can be
	used again.
	(reloc): Don't return 8 and 16 bit non-PC relative relocations on
	ELF, since the ELF object format does not have these type of
	relocations.  Change the abort into as as_bad and return
	BFD_RELOC_NONE to silence compiler warnings.
	(md_assemble): Keep track of the instruction size.  Allow white
	space between the $ and the constant for compatibility with older
	gases and other assemblers.
	(i386_operand): Skip spaces between $ and expression.
	(tc_gen_reloc): Don't allow anything but 32 bit relocations on
	ELF.  Convert abort into an as_bad and assert into as_fatal.

Wed Oct 13 16:50:55 1993  Ken Raeburn  ([email protected])

	* config/obj-coffbfd.c (fixup_segment) [DIFF_EXPR_OK]: If
	sub_symbolP is in the current segment, convert to a PC-relative
	fixup and discard the symbol.

Wed Oct 13 14:00:02 1993  Ian Lance Taylor  ([email protected])

	* config/obj-ecoff.c (ecoff_build_symbols): Handle st_End symbol
	for st_StaticProc just like st_Proc.

	* write.c (relax_and_size_all_segments): Moved #endif for OBJ_BOUT
	so that OBJ_BOUT doesn't forget to adjust all the fragments in the
	.bss section.

Tue Oct 12 17:26:15 1993  Ian Lance Taylor  ([email protected])

	* config/tc-mips.c: If OBJ_ELF, include elf/mips.h.
	(mips_regmask_frag): New static variable, if OBJ_ELF.
	(md_begin): If OBJ_ELF, create .reginfo section and set
	mips_regmask_frag to a frag.
	(mips_elf_final_processing): New function, if OBJ_ELF.  Set
	mips_regmask_frag to register mask information.
	* config/tc-mips.h (elf_tc_final_processing): New macro, defined
	if OBJ_ELF.

Tue Oct 12 03:33:26 1993  Ken Raeburn  ([email protected])

	* messages.c (as_fatal): Use myname when printing messages.

	* config/tc-i960.c (md_begin): Use null pointer, not empty string,
	as initial "return" value in case hashing isn't needed.

	* config/tc-a29k.c (md_atof): Return null, not empty string, on
	success.
	* config/tc-h8300.c (md_atof), config/tc-h8500.c (md_atof),
	config/tc-hppa.c (md_atof), config/tc-i860.c (md_atof),
	config/tc-i960.c (md_atof), config/tc-m88k.c (md_atof),
	config/tc-ns32k.c (md_atof), config/tc-sh.c (md_atof): Ditto.

Mon Oct 11 16:46:31 1993  Steve Chamberlain  ([email protected])

	fix for pr 3571
	* config/tc-h8300.c (get_specific): Special action if 8 bit
	address seen. (check_operand): Don't complain if truncating top
	bits of an 8 bit address.  (build_bytes): Allow an immediate and
	an absolute in the same insn.

Mon Oct 11 17:18:51 1993  Ian Lance Taylor  ([email protected])

	* write.c (write_contents): Don't crash if seginfo is NULL.

	* config/obj-ecoff.c (ecoff_frob_file): Write out register masks
	by modifying .reginfo section, not by directly modifying BFD
	backend data.

Mon Oct 11 14:11:32 1993  david d `zoo' zuhn  ([email protected])

	* config/ho-sunos.h: remove extern time declaration

Mon Oct 11 16:14:43 1993  Ken Raeburn  ([email protected])

	* messages.c (as_fatal): Do mention that it's the assembler that
	got the fatal error.

Fri Oct  8 14:09:35 1993  Ian Lance Taylor  ([email protected])

	* config/tc-mips.c (mips_gprmask, mips_cprmask): New variables to
	hold register masks.
	(md_begin): Initialize them to zero.
	(append_insn): Update mips_gprmask and mips_cprmask.  Also add
	register variables pinfo and prev_pinfo.
	* config/tc-mips.h (mips_gprmask, mips_cprmask): Declare.
	* config/obj-ecoff.c (ecoff_frob_file): If TC_MIPS, set gprmask
	and cprmask from mips_gprmask and mips_cprmask.

	* config/tc-mips.h: Define TARGET_FORMAT if OBJ_ELF.
	* config/tc-mips.c (GPOPT): Define if OBJ_ECOFF or OBJ_ELF.
	(various): Change all references to GP references to apply if
	GPOPT, not if OBJ_ECOFF.
	(s_change_sec): Rearrange somewhat.  If OBJ_ELF, use .rodata
	instead of .rdata.  If OBJ_ELF, set section flags for .rodata and
	.sdata sections.
	(s_frame, s_loc, s_mask): Comment out entire functions, rather
	than just body.  They're not used anyhow.
	* configure.in: Set cpu_type to mips for mips*.  Accept
	mips-*-elfl* and mips-*-elf*.

Thu Oct  7 18:36:29 1993  Michael Meissner  ([email protected])

	* config/obj-elf.c (obj_elf_common): Allow the alignment field to
	not be specified.

Wed Oct  6 13:01:34 1993  Ian Lance Taylor  ([email protected])

	* config/tc-mips.c (cons_fix_new_mips): New function.  Turn
	BFD_RELOC_64 into BFD_RELOC_32.
	* config/tc-mips.h (TC_CONS_FIX_NEW): Define.
	(cons_fix_new_mips): Declare.

	Changes to let cons handle bignums like general expressions.
	* expr.h (expressionS): New field X_unsigned.
	* expr.c (operand): Initialize X_unsigned to 1.  Set it to 0 for
	unary minus case.
	(expr) Fix typo resultP to right if missing operand.  Set
	X_unsigned to 1 when building new expression.
	* read.c (potable): Make "octa" and "quad" call cons, not
	big_cons.
	(cons): Handle bignums.  If given an O_constant (small integer) to
	fill a big space, turn it into a bignum.
	(parse_bitfield_cons): Set X_unsigned field.
	(bignum_low, bignum_limit, bignum_high, grow_bignum, big_cons):
	Removed.
	* read.h (big_cons): Remove prototype.
	* symbols.c (resolve_symbol_value): Don't give a warning if a
	symbol in expr_section can not be resolved.
	(S_SET_VALUE): Clear X_unsigned.
	* write.c (write_object_file): If resolve_symbol_value failed on a
	symbol we are writing out, give a warning.
	* config/tc-h8500.c (parse_reglist): Set X_unsigned.
	* config/tc-hppa.c (md_pseudo_table): Change "octa" and "quad" to
	call pa_cons, not pa_big_cons.
	(pa_big_cons): Remove.
	* config/tc-hppa.h (pa_big_cons): Remove declaration.
	* config/tc-i960.c (md_pseudo_table): Change "quad" to call cons,
	not big_cons.

Tue Oct  5 10:53:36 1993  david d `zoo' zuhn  ([email protected])

	* doc/as.texinfo (Copying): new node, to handle the recent changes
	in the texinfo/gpl.texinfo file

Mon Oct  4 17:10:15 1993  Ian Lance Taylor  ([email protected])

	* read.c (big_cons): Handle "0" correctly.

	* config/tc-mips.c (md_begin): Set target_big_endian correctly.

Mon Oct  4 15:37:57 1993  Ken Raeburn  ([email protected])

	* config/tc-m68k.c (m68k_ip): Mode 7.3 operand using PC should
	have pc-relative fixup.
	(md_parse_option): Move "-k" case down near "-pic" case.

	* configure.in: Alphabetize list of cpu type alternatives.  Enable
	OS values of "linux*elf*" and "linux*coff*" to select those
	formats, with linux emulation.  Don't bother checking for upper-
	or mixed-case versions of "ose".

Thu Sep 30 11:05:35 1993  Steve Chamberlain  ([email protected])

	* config/z8k.c (md_pseudo_table): add "unseg".

Wed Sep 29 16:15:11 1993  K. Richard Pixley  ([email protected])

	* config/m88k-opcode.h (m88k_opcodes): correct a few mistakes
	  found while extending the dissassembler.

Tue Sep 28 12:02:04 1993  Stan Shebs  ([email protected])

	* configure.in: Split i386 LynxOS out from other coff targets,
	add a specific Lynx emulation.
	Add m68k LynxOS target.
	* config/tc-i386.c: Define specific Lynx target format.
	* config/tc-m68k.c: Define specific Lynx target format.
	* config/te-lynx.h: New file.

	* config/obj-coffbfd.h: Don't set TARGET_FORMAT to be
	"coff-{i386,m68k}" if TARGET_FORMAT already defined.
	(INIT_STAB_SECTION): Define.
	* config/obj-coffbfd.c: Include <time.h>.
	(write_object_file): Look for .stab sections and call
	adjust_stab_section.
	(adjust_stab_section): New function, fills in the first symbol
	of a stab section with number of symbols and string table size.
	(obj_coff_init_stab_section): New function, creates the initial
	symbol for a stab section.

Mon Sep 27 15:21:55 1993  Ken Raeburn  ([email protected])

	* config/atof-vax.c (md_atof): Return null on success instead of
	empty string.
	* config/atof-tahoe.c (md_atof): Ditto.
	* read.c (float_cons): Expect a null pointer for success, not an
	empty string.

	* hash.c (hash_insert, hash_jam, hash_grow): Return null pointer
	on success, instead of empty string.  All callers changed.

	* config/tc-vax.c: Use PARAMS in declarations.
	(vip_op): Use NULL instead of empty string for success in error
	and warning fields.

Sun Sep 26 23:45:29 1993  Ken Raeburn  ([email protected])

	* expr.c (expr) [DIFF_EXPR_OK]: Permit subtraction of two symbols
	in different defined segments.

	* write.c (relax_segment): Localize "aim" variable.  If
	DIFF_EXPR_OK, don't impose checks on symbol segment types.
	(fixup_segment) [DIFF_EXPR_OK]: If sub_symbolP is in the current
	segment, convert to a PC-relative fixup and discard the symbol.

	* config/tc-m68k.c (flag_want_pic): New variable, mostly ignored.
	(md_parse_option) [TE_SUN3]: Set it for "-k".
	(m68k_ip): Generate proper fixup for mode 7.3.
	* config/tc-m68k.h (DIFF_EXPR_OK): Define.

Sat Sep 25 05:08:19 1993  Ken Raeburn  ([email protected])

	* config/tc-m68k.c (struct m68k_incant, getone, gettwo): Moved
	earlier in the file.
	(insop, add_exp): Now defined as functions, for readability.
	(insop): Now takes two arguments; callers changed.

Fri Sep 24 12:37:59 1993  K. Richard Pixley  ([email protected])

	* config/tc-m88k.c (get_o6): new function.
	  (get_bf, get_cmp, get_cnd, get_cr, get_fcr, get_imm16, get_reg,
	  get_vec9, getval, get_pcr, calcop, match_name): make static and
	  prototype.
	  (s_file): remove extraneous forward decl.
	  (md_begin): add const to retval decl.
	  (calcop): cope with instructions without arguments.  Handle 'o'
	  type argument, the o6 field of the prot insn.
	  (md_estimate_size_before_relax): return a dummy value.

	* config/m88k-opcode.h (m88k_opcodes): comment change; o6 field is
	  in bits 10 through 7.  flt.[dxs]s requires an r register in the
	  second argument.  New instruction lda.x.  New instruction muls
	  (alias for mul).

Fri Sep 24 13:43:30 1993  Ian Lance Taylor  ([email protected])

	* Makefile.in (distclean): Recurse like clean.
	* doc/Makefile.in (distclean): New target.

	* config/tc-mips.c (md_begin): Set BFD architecture and machine
	based on MIPS ISA level.

Thu Sep 23 17:58:58 1993  Ian Lance Taylor  ([email protected])

	* as.c (main): "exhausted", not "exhuasted".

	* struc-symbol.h (struct symbol): Add sy_used_in_reloc field.
	* write.c (adjust_reloc_syms): Set sy_used_in_reloc.
	(write_object_file): Never strip symbols with sy_used_in_reloc
	set.

	* config/obj-elf.c (obj_elf_section): Rewrote to handle both
	Solaris and SVR4 style .section pseudo-ops.
	(obj_elf_ident): Set SEC_READONLY for .comment section.
	* config/tc-sparc.c (md_apply_fix): If this is ELF, and we're
	generating a reloc, don't apply a fix.

Thu Sep 23 13:16:58 1993  Ken Raeburn  ([email protected])

	* config/obj-coffbfd.c (relax_align): Now static.

Mon Sep 20 19:23:35 1993  Ian Lance Taylor  ([email protected])

	* read.c (get_stab_string_offset): Make non-static.  Make
	arguments const.  Don't align strings to 4 byte boundaries.
	* read.h: Declare get_stab_string_offset.
	* config/obj-elf.c (obj_elf_section): Set SEC_ALLOC as well as
	SEC_LOAD for progbits section.
	(obj_elf_init_stab_section): New function.
	(adjust_stab_sections): Add casts to avoid warnings.
	* config/obj-elf.h (INIT_STAB_SECTION): Call
	obj_elf_init_stab_section.
	(OBJ_PROCESS_STAB): Removed definition.

Fri Sep 17 18:12:34 1993  Ian Lance Taylor  ([email protected])

	* config/obj-elf.h (S_GET_SIZE): Define.
	(obj_frob_forward_symbol): Define.
	* config/tc-i386.c (line_comment_chars): Initialize in all cases.

Thu Sep 16 14:23:08 1993  Ian Lance Taylor  ([email protected])

	* tc.h: Declare tc_gen_reloc differently depending upon
	RELOC_EXPANSION_POSSIBLE.
	* config/obj-elf.c (obj_elf_section): Only set flags when first
	creating the section.

Wed Sep 15 12:15:53 1993  Ian Lance Taylor  ([email protected])

	* config/tc-mips.c (append_insn): Don't swap a trap instruction
	with a branch.

Tue Sep 14 13:31:04 1993  Ian Lance Taylor  ([email protected])

	* config/obj-elf.c (obj_elf_data, obj_elf_text): New functions;
	set previous_section and previous_subsection and then call s_data
	and s_text, respectively.
	(obj_pseudo_table): Add data and text.
	(obj_elf_section): Add SEC_LOAD to default initialization of
	flags.  Treat .rodata1 like .rodata.  Set SEC_LOAD as well as
	SEC_ALLOC for "alloc" string.  Don't bother trying to find the
	section; just use subseg_new.

	* read.c (change_to_section): Removed.  This is now done by
	subseg_new.
	(get_stab_string_offset): Rearranged somewhat.  Create the section
	using subseg_new.  Store the string index in seg_info, rather than
	in a static variable.  Force the first string to be empty.  Use
	frag_more rather than FRAG_APPEND_1_CHAR.
	(s_stab_generic): Rewrote.
	* subsegs.h (segment_info_type): Added stabu union.
	* subsegs.c (subseg_new): Initialize stab_string_size to 0.
	* config/obj-aout.c: Don't include aout/stab_gnu.h.
	(obj_aout_stab, obj_aout_desc): Removed.
	(obj_pseudo_table): Removed desc and stabX entries.
	* config/obj-bout.c: Same changes as config/obj-aout.c.
	* config/obj-bout.h (S_SET_TYPE): Define.
	(tc_bout_fix_to_chars): Declare.
	* config/obj-coff.c (obj_coff_stab): Removed.
	(obj_pseudo_table): Removed desc and stabX entries.
	* config/obj-coff.h (SEPARATE_STAB_SECTIONS): Define.
	* config/obj-coffbfd.c (current_stab_symbol): Removed.
	* config/obj-coffbfd.h (obj_symbol_type): Removed n_strx, n_type,
	n_other, n_desc and n_value fields.
	(S_{S,G}ET_{OFFSET,OTHER,TYPE,DESC}): Removed.
	(MAKE_STAB_SYMBOL): Removed.
	* config/obj-ecoff.c (obj_ecoff_stab): Renamed to ecoff_stab.
	Changed arguments and removed parsing code.
	(obj_pseudo_table): Removed stabX entries.
	* config/obj-ecoff.h (ecoff_stab): Declare.
	(OBJ_PROCESS_STAB): Define.
	* config/obj-elf.c: Don't include aout/stab_gnu.h.
	(obj_elf_stab, obj_elf_xstab, obj_elf_desc,
	elf_stab_symbol_string, elf_stab_symbol, obj_elf_stab_generic):
	Removed.
	(obj_pseudo_table): Removed desc, stabX and xstabs entries.
	(obj_elf_version): Use subseg_new, not bfd_make_section.  Don't
	set SEC_LOAD for .note section.
	(adjust_stab_sections): Get frag pointer from seg_info, rather
	than looking through frags.
	* config/obj-elf.h (S_{S,G}ET_{OTHER,TYPE,DESC}): Removed.
	(SEPARATE_STAB_SECTIONS, INIT_STAB_SECTION, OBJ_PROCESS_STAB):
	Define.
	* config/obj-vms.c (obj_aout_stab): Removed.
	(obj_pseudo_table): Removed stabX entries.
	* config/obj-vms.h (S_SET_TYPE): Define.

	* as.h: Declare listing.
	* read.c: Don't declare listing.
	(emit_expr): Cast fix_new_exp argument.
	(parse_bitfield_cons): Correct printf format.
	* symbols.c (symbol_new): Add cast to avoid warning.
	* write.h: Declare text_last_frag and data_last_frag.
	* config/obj-bout.c (obj_bout_line): Added dummy argument.
	* config/obj-coffbfd.c: Add some casts to avoid warnings.
	* config/tc-a29k.c: Likewise.
	* config/tc-i960.c: Likewise.  Also fully bracket structure
	initializations, fix printf formats, and remove unused variables.

Mon Sep 13 16:48:38 1993  Ian Lance Taylor  ([email protected])

	* read.c (s_desc): Only compile and use if S_SET_DESC is defined.
	* struc-symbol.h: Declare verify_symbol_chain and
	verify_symbol_chain_2 even if not SYMBOLS_NEED_BACKPOINTERS.
	* symbols.c (verify_symbol_chain): Removed useless expression.
	* write.c (headers, the_object_file): Only use if not
	BFD_ASSEMBLER and not BFD.
	(fixup_segment, cvs_frag_to_fill): Only use if BFD_ASSEMBLER or
	not BFD.
	(merge_data_into_text): Only use if BFD_ASSEMBLER or (not BFD and
	not OBJ_AOUT).
	* write.h: Declare relax_segment.
	* config/obj-coffbfd.c (stack_pop, stack_push, stack_init): Made
	static.
	(stack_top): Commented out, since it's not used.
	Fixed up pseudo-op functions to take an ignored int argument.
	(size_section): Added default BAD_CASE to switch.
	Changed bzero calls to memset.
	* config/obj-coffbfd.h (S_IS_LOCAL): Call strchr on S_GET_NAME
	(s), not on s itself.
	* config/tc-a29k.c (s_use): Take ignored int argument.  Only
	define if OBJ_COFF is not defined.
	* config/tc-i386.c: (fits_in_signed_byte, smallest_imm_type): Make
	argument signed again.
	* config/tc-m68k.c (s_bss, s_even, s_proc): Take ignored int
	argument.
	(m68k_ip): Fully bracket initialization of archs.
	Correct several formats for __LINE__ to be %d rather than %s.
	(init_table): Fully bracket initialization.
	Cast values larger than 0x7f assigned to fr_opcode to char.

	* subsegs.c: Renamed non-BFD_ASSEMBLER subseg_new to subseg_set.
	Wrote non-BFD_ASSEMBLER subseg_new.  Now subseg_new always takes a
	section name, and subseg_set always takes a segT.  Changed all
	callers as appropriate.
	* config/obj-coffbfd.c 	(change_to_section): Renamed to
	obj_coff_add_segment.  Corrected.  Made callers use subseg_new.
	* config/obj-coffbfd.h (obj_segment_name, obj_add_segment):
	Define.

Mon Sep 13 13:15:03 1993  Doug Evans  ([email protected])

	* config/tc-sparc.h (LOCAL_LABEL): Remove test for name[0] == 'L'.

Fri Sep 10 11:22:08 1993  Ian Lance Taylor  ([email protected])

	* config/obj-elf.h (S_SET_SIZE): Actually set the size.

	Gcc lint.
	* Added a number of casts to function calls.
	* app.c (do_scrub_begin), as.c (main), expr.c (integer_constant,
	operand, expr), read.c (read_begin, HANDLE_CONDITIONAL_ASSEMBLY,
	read_a_source_file, s_align_bytes, demand_empty_rest_of_line,
	ignore_rest_of_line, big_cons, is_it_end_of_statement, s_ignore),
	read.h (is_name_beginner, is_part_of_name), config/obj-elf.c
	(obj_elf_section), config/tc-i386.c (parse_register),
	config/tc-sparc.c (isoctal, s_proc): Cast char
	array indices to unsigned char.
	* app.c (process_escape): Make static.  Add prototype.  Change
	argument from char to int.
	* as.c: Include output-file.h for prototypes.  Comment out unused
	function got_sig.
	* Makefile.in (as.o): Depend on output-file.h.
	* as.h (BAD_CASE): Cast val argument to long, and use %ld.
	(pseudo_typeS): Add prototype to poc_handler field.
	(print_version_id): Add prototype.
	(xmalloc, xrealloc): Change size arguments to unsigned long.
	(do_scrub_next_char): Add prototypes for function arguments.
	(had_errors, had_warnings, scrub_from_file): Remove duplicate
	declarations.
	* atof-generic.c (atof_generic): Make size variables unsigned.
	* cond.c (ignore_input): Removed unused local variable ptr.
	* expr.c (floating_constant, integer_constant): Make static.  Add
	prototypes.
	* flonum-copy.c (flonum_copy): Make size variables unsigned.
	* frags.h: Add prototype for frag_init.
	* hash.h, hash.c: Change hash values from char * to PTR, make hash
	strings const, make returned error strings const char *.  Added
	prototypes for functions.
	* input-file.h, input-file.c (input_file_buffer_size): Return
	unsigned int.
	* input-scrub.c (buffer_length): Make unsigned.
	(input_scrub_push, input_scrub_pop): Make static.
	* listing.c (list_symbol_table): Cast sprintf argument to unsigned
	long and use %lx.  Print name of segment rather than address of
	structure.
	(listing_list, listing_title): Change argument to int.
	(listing_eject, listing_flags, listing_psize): Add int argument.
	* listing.h: Corresponding declaration changes.
	* obj.h (obj_emit_symbols): Rename prototype argument to avoid
	shadowing.
	* read.h: Change get_absolute_expression prototype to return
	offsetT.  Add prototype for next_char_of_string.  Various
	prototype changes.
	* read.c: Remove prototype for next_char_of_string.
	(pobegin): Make errtxt const.  Make new_length, tmp_len and num
	unsigned.
	(s_abort, s_align_ptwo, s_comm, s_data, s_app_line, s_fill,
	s_globl, s_lsym, s_org, s_set, s_text, s_desc): Add int argument.
	Change all callers.
	(s_comm): Change temp from valueT to offsetT.  Cast to long when
	printing and use %ld (only for error messages anyhow).
	(s_long, s_int): Remove unused functions.
	(cons): Change argument to int.
	(emit_expr): Use %lx when printing longs.
	(get_absolute_expression): Return offsetT, not long.
	(get_stab_string_offset): Comment out unless
	SEPARATE_STAB_SECTIONS.
	(s_stab_generic): Remove unused offset.  Define seg_is_new only
	if SEPARATE_STAB_SECTIONS.  Use toP only in local block.
	* struc-symbol.h (verify_symbol_chain_2): Add prototype.
	* symbols.c: Remove nested comment.
	(symbol_new): Rename value to valu.
	(colon): Use %ld and cast to long in error message.
	* symbols.h: Remove duplicate verify_symbol_chain declaration.
	* tc.h: Remove unused md_emit_relocations declaration.
	(tc_gen_reloc): Add declaration.
	* write.c (cvt_frag_to_fill): Change first argument name depending
	on BFD_ASSEMBLER.
	(write_relocs): Remove unused offset, frags.  Remove tc_gen_reloc
	declarations.  Make n unsigned.
	(write_contents): Remove unused i, n, relocs, fixp.  Rename frags
	to f to avoid shadowing.
	(write_object_file): Define fragP only if not BFD_ASSEMBLER or not
	WORKING_DOT_WORD.  Remove unused keep.  Only declare punt and
	punt_it if they will be used.  Make i and n unsigned.
	(fixup_segment): Cast to long and use %ld in error message.
	* xmalloc.c (xmalloc, xrealloc): Make size argument unsigned.
	* config/obj-aout.h: Remove nested comment.  Add prototype for
	obj_aout_frob_symbol.
	(obj_aout_line, obj_aout_desc): Add int argument.
	* config/obj-ecoff.c: Changed build routines to use an unsigned
	offset.
	(add_string): Make len unsigned long.
	(obj_ecoff_stab): Use %lu in error message.
	* config/obj-elf.c (obj_elf_common): Comment out unused label
	allocate_bss.
	(obj_elf_frob_symbol): Return 0 (currently broken).
	(obj_elf_desc, obj_elf_version, obj_elf_size, obj_elf_type,
	obj_elf_ident, obj_elf_weak, obj_elf_local, obj_elf_common,
	obj_elf_line, obj_elf_previous): Add int argument.
	(obj_elf_write_symbol_p): Make static.
	* config/obj-elf.h (obj_elf_write_symbol): Add prototype.
	* config/tc-hppa.h: Remove declarations of functions declared in
	read.h.
	* config/tc-i386.c (ENCODE_RELAX_STATE): Cast to relax_substateT.
	(s_bss): Add int argument.
	(fits_in_signed_byte, smallest_imm_type): Make argument unsigned.
	(dummy): Remove unused function.
	(md_assemble): Rename local o to op to avoid shadowing.
	(tc_gen_reloc): Rename local reloc to rel to avoid shadowing.
	* config/tc-m68k.c (s_data1, s_data2): Add int argument.
	* config/tc-mips.c (mips_ip, md_apply_fix): Cast to long and use
	%ld in error messages.
	* config/tc-sparc.c: Remove duplicate declarations.
	(getExpression): Rewrite condition to avoid empty conditional
	body.
	(s_reg, s_proc, s_reserve, s_common, s_seg, s_xword): Add int
	argument.

Thu Sep  9 17:10:00 1993  Ken Raeburn  ([email protected])

	Changes from Jeff Law:

	* config/tc-hppa.c (md_assemble): Fix typo.
	(pa_ip): Delete unused variables and labels.  Do not check for
	unsigned values being < 0, it can't happen.
	(is_same_frag): Return a value in recursive call case.
	(pa_callinfo): Delete unused variables and labels.
	(pa_comm): Likewise.
	(pa_copyright): Likewise.
	(pa_export): Likewise.
	(pa_import): Likewise.
	(pa_param): Likewise.
	(pa_space): Likewise.
	(pa_subspace): Likewise.

Thu Sep  9 15:05:34 1993  Ian Lance Taylor  ([email protected])

	* read.c (get_stab_string_offset, s_stab_generic): If
	BFD_ASSEMBLER, call subseg_set rather than subseg_new.

Wed Sep  8 15:09:17 1993  Ian Lance Taylor  ([email protected])

	* config/obj-elf.c (obj_elf_section): Set SEC_LOAD when using
	default flag values.

Tue Sep  7 10:22:52 1993  Stan Shebs  ([email protected])

	* read.c: (change_to_section): Don't include body if not MANY_SECTIONS.

	* read.c: (s_stab, s_xstab, s_desc): New functions to parse
	various stab-related directives.
	* read.h: (s_stab, s_xstab, s_desc): New function prototypes.
	* write.c: (merge_data_into_text): Fix ifdef tangle.
	* config/obj-coffbfd.c (current_stab_symbol): Fake symbol
	for stab reader to use.
	* config/obj-coffbfdh.h (obj_symbol_type): Added fields for
	stab reader, macros to access.

Fri Sep  3 16:44:03 1993  Ken Raeburn  ([email protected])

	* config/obj-elf.h (elf_symbol): Fixed name of elf_symbol_type.

	* config/tc-hppa.h (struct default_subspace_dict, struct
	default_space_dict): Field "sort" is now unsigned char.

	* config/tc-hppa.c (pa_def_subspaces, pa_def_spaces): Align
	columns for easier reading.
	(bcmp, index): Deleted USG-specific definitions.  Should be dealt
	with in ho-*.h, or in libiberty.  Changed mention of index to
	strchr.
	(label_symbolP, label_symbol_defined, callinfo_found,
	within_entry_exit, exit_processing_complete, within_procedure,
	pa_def_subspaces, pa_def_spaces, pa_pseudo_op_moves_pc,
	label_symbols_rootP, pa_get_label, pa_label_is_defined,
	pa_undefine_label): Now static.
	(movers): Now const, in addition to pointing to const data.
	* config/tc-hppa.h (label_symbolS_rootP, pa_get_label,
	pa_label_is_defined, pa_undefine_label, pa_pseudo_op_moves_pc):
	Delete declarations.

	Merged more changes from Jeff Law and Pete Hoogenboom:

	* config/tc-hppa.c (pa_def_subspaces, pa_def_subspaces): Remove
	entries for .stab and .stabstr.

	* config/obj-elf.c: (elf_stab_symbol_string):  Set the
	SEC_LOAD attribute for the .stabstr section.
	(obj_elf_stab_generic):  Set the SEC_LOAD attribute for the
	.stab section.
	(obj_elf_stab_generic):  Change '#if 1' to '#if 0'.
	(obj_elf_stab_generic):  Incorrect byte count on call to
	md_number_to_chars function.

	* config/tc-hppa.c (hppa_tc_symbol): Static functions need
	argument relocation bits too.

	* config/tc-hppa.c (pa_stringer): Correctly handle escaping
	characters which should appear unaltered in the output string (for
	example an escaped double-quote).

	* config/tc-hppa.c (pa_parse_nonneg_cmpsub_cmpltr): Always
	initialize name.
	(pa_parse_neg_cmpsub_cmpltr): Likewise.
	(pa_parse_nonneg_add_cmpltr): Likewise.
	(pa_parse_neg_add_cmpltr): Likewise.

	* config/tc-hppa.h (parse_cons_expression_hppa): Remove prototype
	for now.
	(cons_fix_new_hppa): Likewise.
	* config/tc-hppa.c (md_apply_fix): Fix type of valp to match
	prototype.

	* config/tc-hppa.c: Include libhppa.h.

	* config/tc-hppa.h: Delete extern declarations of functions
	found in libhppa.h.

	* config/tc-hppa.c (pa_space): Rework to avoid unwanted #ifdef
	OBJ_ELF conditionals.
	* config/tc-hppa.h (LOCAL_LABEL): Correctly identify local labels
	on the PA.

Thu Sep  2 10:43:57 1993  Ian Lance Taylor  ([email protected])

	* config/tc-mips.c (macro_build): Accept 'z', and ignore it.
	(macro): Use "z,s,t" for div instructions to match corresponding
	change in opcode table.
	(mips_ip): Added 'z'--must be zero register.

Wed Sep  1 15:56:42 1993  Ken Raeburn  ([email protected])

	* write.c (write_relocs) [RELOC_EXPANSION_POSSIBLE]: Declare
	tc_gen_reloc correctly.

	* configure.in: Use "case" instead of "if" when possible.  Rewrote
	Makefile editing to reduce work done.  Treat "hppa*" as "hppa".

Wed Sep  1 12:19:07 1993  K. Richard Pixley  ([email protected])

	* config/obj-coffbfd.c (obj_coff_section): add 'd' as an alias for
	  section type of data.  'd' seems to be used for m88k.

Wed Aug 25 22:33:22 1993  Ian Lance Taylor  ([email protected])

	* config/tc-mips.c (mips_align, s_stringer, s_cons, s_float_cons,
	s_mips_space): Set insn_label to NULL to avoid changing it at the
	next .align statement.
	(append_insn): Don't swap jal with instruction that sets the
	register that jal sets.

Wed Aug 25 16:15:57 1993  K. Richard Pixley  ([email protected])

	* configure.in: recognize m88110.

Wed Aug 25 13:37:46 1993  Ken Raeburn  ([email protected])

	Merged changes from Pete Hoogenboom and Jeff Law at Utah:
	* config/tc-hppa.c (pa_build_unwind_subspace): SEC_ALLOC should
	not be on for .hppa_unwind.
	(md_pseudo_table): .PARAM and .param are valid pseudo-ops for GAS.
	(pa_param): New function to handle .PARAM directives.
	(pa_ip): Pass "isbranch" argument down to pa_parse_*_compltr
	functions.  Handle '|' for movb; allow movb,n.
	(pa_parse_nonneg_cmpsub_cmpltr): Delete old useless
	version.  Handle cases where no completer exists for
	comb,n or addb,n.
	(pa_parse_neg_cmpsub_cmpltr): Handle cases where no
	completer exists for comb,n or addb,n.  Make logic
	mirror that of pa_parse_nonneg_cmpsub_cmpltr.
	(pa_parse_nonneg_add_cmpltr): Likewise.
	(pa_parse_neg_add_cmpltr): Likewise.
	* tc-hppa.h (pa_param): Declare.

Tue Aug 24 15:41:35 1993  Ken Raeburn  ([email protected])

	* config/tc-hppa.c (hppa_tc_make_symextn_section): Now static.
	Added forward declaration.

	Merged changes from Pete Hoogenboom and Jeff Law at Utah:

	* config/obj-elf.c (elf_frob_file): Arguments were incorrect on
	call to elf_tc_make_sections.
	(obj_elf_version): A .note section shouldn't have the SEC_ALLOC
	attribute.

	* config/tc-hppa.c (hppa_tc_make_sections): Add some processing to
	handle symbol extension sections.

	* config/tc-hppa.c (pa_build_symextn_section): New function to
	create a symbol extension section.
	(pa_export_args): Make call to pa_build_symextn_section.
	(hppa_tc_symbol, hppa_tc_make_sections,
	hppa_tc_make_symextn_section): New functions.
	* config/tc-hppa.h: Update elf_tc_symbol and elf_tc_make_sections
	macros.

	* read.c (emit_expr): Place check for TC_CONS_FIX_NEW in the
	BFD_ASSEMBLER branch as well.

	* config/tc-hppa.h: If ELF is the target object format, define
	some ELF- and hppa-specific types and constants.

	* config/tc-hppa.c (getExpression): Fix a typo.

	* read.c (read_a_source_file): Use TC_EQUAL_IN_INSN to determine
	if a `=' is part of an instruction.
	(read_a_source_file): Handle case where end-of-line markers are
	also used within instructions.
	* config/tc-hppa.h (TC_EQUAL_IN_INSN, TC_EOL_IN_INSN): Define.

	* config/tc-hppa.c (md_apply_fix_1): Keep relocations for
	out-of-range branches/'calls using "bl" or calls which may need
	argument relocation stubs.  Do not need/keep relocations for
	conditional branches.
	(elf_hppa_final_processing): Fix calculation of function size.

	* config/obj-elf.c (obj_elf_version): Mark .note section as
	READONLY.

	* config/tc-hppa.c (parse_cons_expression_hppa): Pass exp, not the
	address of exp, to expression.
	(pa_build_unwind_subspace): Turn SEC_HAS_CONTENTS flag on.
	(md_apply_fix_1): Delete unwanted comments.
	(process_exit): Symbols marking the end of a function are always
	BSF_LOCAL.

	* config/tc-hppa.c: Include elf32-hppa.h from BFD tree.
	(pa_space): Declare and initialize gdb_section.

	* config/obj-elf.c (elf_frob_file): Change
	elf_tc_final_processing_hook to elf_tc_final_processing.

	* config/tc-hppa.c (fix_new_hppa): Fix argument list to match
	argument type declarations.
	(getExpression): Fix typo.
	(pa_export_args): Change elf_symbol_type to elf32_symbol_type.
	(elf_hppa_final_processing): Likewise.  Name changed from
	elf_hppa_final_processing_hook.
	(start_symbol_root, start_symbol_last): Deleted.

	* config/tc-hppa.h (TC_PARSE_CONS_EXPRESSION): Fix typo.

	* config/tc-hppa.h: Replace "symbolS" with "struct symbol" to
	avoid changing include ordering.

	* config/tc-hppa.c (pa_ip, case 'y'): Handle just like 't'.

Mon Aug 23 12:47:58 1993  Ian Lance Taylor  ([email protected])

	* config/tc-mips.c (set_at): Added unsignedp argument.  Use
	load_register.
	(set_at_unsigned): Removed; changed callers to use set_at.
	(load_register): Removed unused ip argument.  Changed callers.
	(append_insn): Don't swap branch and branch likely.
	(macro_build): Handle 'u'.
	(load_register): Handle 64 bit constants.
	(macro): Added M_DABS, removed M_ABSU.  Numerous changes to
	support 64 bit constants.
	(mips_ip): Use hex constants in range checks for clarity.
	(md_number_to_chars): Support 8 byte values.

Fri Aug 20 16:50:59 1993  K. Richard Pixley  ([email protected])

	* config/tc-m88k.h: updated copyrights.
	  (TC_CONS_RELOC): declare to be RELOC_32.

Fri Aug 20 11:16:44 1993  Ian Lance Taylor  ([email protected])

	* config/tc-mips.c (mips_isa): New static variable.
	(md_begin): Initialize mips_isa based on TARGET_CPU.  Don't sanity
	check macros.  Set text alignment and GP size here.
	(md_assemble): Don't set text alignment and GP size here.
	(append_insn): Don't insert NOPs for load delays if mips_isa >= 2.
	Use the right mask and shift for WRITE_FPR_T and WRITE_FPR_S.  Add
	a NOP after a branch likely.
	(mips_emit_delays): Don't insert NOPS for load delays if mips_isa
	>= 2.
	(macro): Support r6000 and r4000 macros.
	(mips_ip): Check insn ISA level against mips_isa before using it.
	Added 'x' case for ignored register.
	(md_parse_option): Handle -mipsN and -mcpu=XX.

Fri Aug 20 01:26:52 1993  Ken Raeburn  ([email protected])

	* config/tc-i386.c (md_pseudo_table) [OBJ_ELF]: Handle ".zero".

Thu Aug 19 12:15:18 1993  Ken Raeburn  ([email protected])

	* config/tc-sparc.c (s_local): Function moved and renamed...
	* config/obj-elf.c (obj_elf_local): ...to here.
	* config/tc-sparc.c (md_pseudo_table), config/obj-elf.c
	(obj_pseudo_table): Move handling of ".local".

	* tc.h (md_parse_option): Don't declare if defined as a macro.

	* config/tc-i386.h (NO_RELOC) [BFD_ASSEMBLER]: Define as
	BFD_RELOC_NONE.
	(md_parse_option): New macro, converted from function.
	* config/tc-i386.c (md_parse_option): Function deleted.
	(comment_chars) [OBJ_ELF]: Include "/".
	(line_comment_chars) [OBJ_ELF || TE_I386AIX]: Don't include "/".
	(md_assemble): Cast 0xe9 to char explicitly, to avoid compiler
	warning.
	(md_assemble, md_estimate_size_before_relax, md_create_long_jump):
	Call reloc for fix_new type, or use correct enumerator, instead of
	always using NO_RELOC.
	(i386_operand): Change "ifndef I386COFF" to "ifdef OBJ_AOUT" for
	tests for valid section.
	(md_convert_frag) [BFD_ASSEMBLER]: Compensate for frag start
	address.
	(md_apply_fix_1) [BFD_ASSEMBLER]: For pc-relative reloc with
	symbol, compensate for location of reloc.
	(reloc, BFD_RELOC_32, BFD_RELOC_32_PCREL) [!BFD_ASSEMBLER]: Define
	to return zero.

Wed Aug 18 16:51:29 1993  Ken Raeburn  ([email protected])

	* config/obj-elf.c: Undef NO_RELOC before including aout/aout64.h.
	(obj_elf_weak): New function.
	(obj_pseudo_table): Handle ".weak".
	(obj_elf_section): If section directive includes a string, ignore
	it for now.  Accept "progbits" flag.
	(obj_elf_type): Accept `@' before flag name.

	* write.c (relax_and_size_seg) [BFD_ASSEMBLER]: Get rid of `if(1)'
	condition.
	(fixup_segment) [BFD_ASSEMBLER]: Use bfd_is_com_section, rather
	than checking for bfd_com_section directly.
	(fixup_segment): Simplify range check.
	(fixup_segment) [OBJ_COFF && TC_I960]: Simplify cpp condition
	test.

	* symbols.h (S_SET_WEAK): Declare.
	* symbols.c (S_SET_WEAK): New function.
	(S_SET_EXTERNAL, S_CLEAR_EXTERNAL): Don't bother with BSF_EXPORT,
	it's not a separate flag any more.  Clear BSF_WEAK.

	* read.c (potable): Treat "string" like "asciz".

Wed Aug 18 15:30:29 1993  Ian Lance Taylor  ([email protected])

	* config/tc-mips.c (append_insn): Don't swap branch instructions
	if .set nobopt or .set volatile.
	(gp_reference): .lit8 and .lit4 are accessed via the GP register.
	(macro): Added cases M_LI_S, M_LI_SS.  Fixed M_LI_D and M_LI_DD.
	(mips_ip): Added cases 'F', 'L', 'f', 'l' for floating point.
	* config/obj-ecoff.c: Renamed some variables to avoid shadow
	warnings.

Mon Aug 16 14:16:02 1993  david d `zoo' zuhn  ([email protected])

	* config/obj-coff.h (S_IS_COMMON): add missing backslash

	* configure.in (z8k-*-{coff,sim}): use coffbfd for this target

Thu Aug 12 11:47:58 1993  Ian Lance Taylor  ([email protected])

	* config/tc-mips.c (mips_ip): Suggested by
	[email protected] (David Johnson): Don't accept symbolic
	names for 'E' and 'G' argument types (coprocessor registers) and
	don't warn if $1 is used on the coprocessor.
	(macro): Handle M_{L,S}WC{0,2,3}_AB correctly.

Mon Aug  9 12:09:14 1993  Doug Evans  ([email protected])

	* read.c (emit_expr): Use BFD_RELOC_16 for 2-byte values.
	* config/tc-sparc.c (md_apply_fix, tc_gen_reloc): Handle
	BFD_RELOC_16.
	* config/tc-sparc.h (WORKING_DOT_WORD): Define.

Mon Aug  9 13:36:22 1993  Ken Raeburn  ([email protected])

	* write.c (merge_data_into_text): Define only if BFD_ASSEMBLER is
	defined or BFD is not.
	(relax_and_size_all_segments): Declare local variable fragP.

Fri Aug  6 15:22:53 1993  Ken Raeburn  ([email protected])

	* config/tc-sparc.c (md_apply_fix, case BFD_RELOC_32): Fill in
	bytes with real values, not zeros.

Fri Aug  6 10:57:59 1993  Ian Lance Taylor  ([email protected])

	* configure.in (mips-*-riscos*, mips-*-sysv*): New (untested)
	targets, using ecoff and mips-big.

	* config/tc-mips.c (mips_ip): From [email protected] (David
	Johnson): Added case for 'C' for coprocessor instruction codes.

Thu Aug  5 13:08:56 1993  Ken Raeburn  ([email protected])

	* config/obj-elf.c (obj_pseudo_table): Handle ".8byte".

	* read.c (emit_expr): Use BFD_RELOC_64 for 8-byte expressions.

	* write.c (write_object_file): Test DEBUG_SYMS instead of DEBUG
	for verifying symbol chain.
	(merge_data_into_text, relax_and_size_all_segments): New
	functions, split out from write_object_file.

Tue Aug  3 15:43:55 1993  Ken Raeburn  ([email protected])

	* config/obj-elf.c (obj_elf_stab_generic, in disabled code): If
	debug section is new, allocate an extra 12 bytes at its start.  If
	".stabs" type is N_SO, fill in filename symbol field of that first
	entry.  Return early if "goof", to simplify later code slightly.
	(adjust_stab_sections): New function.
	(elf_frob_file): Apply adjust_stab_sections to each section.

	* config/obj-elf.c (obj_elf_section, obj_elf_previous): No longer
	static.
	* config/obj-elf.h (obj_elf_section, obj_elf_previous): Declare.
	* config/tc-sparc.c (md_pseudo_table): Call them for "pushsection"
	and "popsection", and call cons for "uaword" and "uahalf".

	* config/obj-elf.c (obj_elf_version): Use English in error
	messages.

Tue Aug  3 11:29:06 1993  Ian Lance Taylor  ([email protected])

	* config/obj-ecoff.c: Updated for BFD ECOFF changes.  Now gets the
	swapping routines and external structure sizes via the
	ecoff_backend information.  No longer includes coff/mips.h.

Mon Aug  2 17:35:48 1993  Ian Lance Taylor  ([email protected])

	* config/obj-ecoff.c (get_tag): Save tag name in permanent memory
	and in hash_ptr->string.

	* app.c (do_scrub_next_char): Reset state to 0 after .appline if
	file name is not seen.

Thu Jul 29 22:21:28 1993  Ian Lance Taylor  ([email protected])

	* write.c: Don't use short int in a prototype.

	* expr.c (operand): Make return value simply depend on contents of
	returned expression.

Thu Jul 29 18:38:37 1993  david d `zoo' zuhn  ([email protected])

	* configure.in: sparc*-aout and sparc*-vxworks are BFD assemblers

Thu Jul 29 18:38:37 1993  david d `zoo' zuhn  ([email protected])

	* config/ho-sunos.h: remove some old function decls that conflict
	w/ ANSI, and which weren't needed anyway

Wed Jul 28 16:34:55 1993  Ken Raeburn  ([email protected])

	* config/obj-elf.h (obj_frob_symbol): Renamed from tc_frob_symbol,
	and disabled since it breaks Ian's new symbol-value code.

	* expr.c (integer_constant): Accept more digits if BFD64.

Wed Jul 28 11:30:05 1993  Ian Lance Taylor  ([email protected])

	* config/tc-m68k.c (m68k_ip): If we have a normal constant when we
	expect a bignum, turn it into a bignum.  Output extra zeroes
	before a short bignum, rather than after.

Tue Jul 27 15:54:27 1993  Ken Raeburn  ([email protected])

	* symbols.c (symbol_new): Conditionalize verify_symbol_chain call
	on DEBUG_SYMS, not DEBUG.
	(symbol_remove): Likewise.
	(symbol_insert): Likewise.

Tue Jul 27 08:45:05 1993  Ian Lance Taylor  ([email protected])

	* config/tc-mips.c (mips_optimize): New static variable.
	(append_insn): If mips_optimize == 0, always insert NOP
	instructions.  If mips_optimize < 2, don't swap branches.
	(md_parse_option): If -Ox or -gx, set mips_optimize accordingly.

Mon Jul 26 18:02:43 1993  K. Richard Pixley  ([email protected])

	* Makefile.in (clean): if testsuite does not exist, then skip it.

Fri Jul 23 14:13:25 1993  Ian Lance Taylor  ([email protected])

	* config/tc-mips.c (prev_insn_unreordered,
	prev_prev_insn_unreordered): New static variables.
	(append_insn): Don't swap branch instruction if
	prev_prev_insn_unreordered (see comment).
	(mips_no_prev_insn): Clear the unreordered variables.
	(s_mipsset): When turning on reordering, set the unreordered
	variables.

Fri Jul 23 13:09:44 1993  Ken Raeburn  ([email protected])

	* config/obj-elf.c (obj_elf_section): Sections ".init" and ".fini"
	are also magic, and have special default flag settings.
	(obj_elf_frob_symbol): Since the return value from this function
	isn't used, don't bother calling obj_elf_write_symbol_p, since it
	doesn't accomplish anything else.

	* config/tc-sparc.c (md_section_align): Round up section size only
	for a.out format.

	* symbols.c: Don't define DEBUG by default.

Thu Jul 22 12:09:41 1993  Ian Lance Taylor  ([email protected])

	* write.c (fix_new_exp): Handle a O_uminus expression.

	* expr.c (expr): Don't let absolute_section override
	undefined_section for the return value.

	* read.c (read_a_source_file): In NO_PSEUDO_DOT case, if we find a
	pseudo-op with a poc_handler field of NULL, ignore it and treat it
	as an instruction instead.
	* config/tc-m88k.c (md_pseudo_table): Add "set" with a NULL
	poc_handler field.

	* config/tc-h8500.c (md_begin): Use a local variable when
	initializing md_relax_table to avoid warnings about modifying a
	supposedly const data structure.

Thu Jul 22 10:58:51 1993  Brendan Kehoe  ([email protected])

	* config/obj-aout.c: Only include aout/aout64.h if BFD_ASSEMBLER
	is defined.

Wed Jul 21 17:32:02 1993  Fred Fish  ([email protected])

	* configure.in (case ${host}):  Map *-*-sysv4* to gas_host=sysv.
	* configure.in (case ${generic_target}):  Add i[34]86-*-sysv4*
	case to set obj_format=elf.  Must go before i386-*-sysv* case that
	sets obj_format=coffbsd.  Add *-*-sysv4* to *-*-elf and
	*-*-solaris case, and move to before *-sysv* case that wants to
	set obj_format to coff.
	* config/tc-i386.c (i386_operand): Change all 'exp.X_op' to
	'exp->X_op'.
	* config/tc-i386.c (md_apply_fix):  Fix valp to be 'valueT *' for
	BFD_ASSEMBLER case.

Wed Jul 21 12:47:51 1993  Ian Lance Taylor  ([email protected])

	* config/obj-aout.c: Include aout/aout64.h.
	(obj_aout_frob_symbol): Set BSF_DEBUGGING for a constructor
	symbol, so that BFD doesn't tamper with the type.

	* read.c (read_a_source_file): If NO_PSEUDO_DOT is defined, look
	up opcodes as pseudo-ops even if they don't start with '.'.
	* config/tc-m88k.h (NO_PSEUDO_DOT): Define.
	* config/tc-m88k.c (md_assemble): Removed special pseudo-op
	handling.
	(md_apply_fix): Set fx_offset to the upper 16 bits of the reloc.
	Output the low 16 bits for RELOC_HI16, not the high 16 bits.
	* config/obj-coffbfd.c (do_relocs_for): If TC_M88K, set the
	r_offset field of the reloc to the fixup offset.
	(fixup_segments): If TC_M88K, don't warn about fixup overflows.
	* doc/as.texinfo: Minor updates.

Tue Jul 20 19:28:56 1993  Ian Lance Taylor  ([email protected])

	* Extensive changes to permit symbols to contain any expression
	type and to delay the computation of the expression until the
	value is actually needed.  This permits setting symbols to values
	calculated based on object code size.  Expressions were changed to
	no longer be in a section, to stop the overloading of segment and
	expression type that previously occurred.

	* as.c (big_section, pass1_section, diff_section, absent_section):
	Removed.
	(expr_section): Added (used for dummy symbols which hold
	intermediate expression values).
	(perform_an_assembly_pass): Create expr_section, do not create the
	sections now removed.
	* as.h (segT): Removed SEG_ABSENT, SEG_PASS1, SEG_BIG, and
	SEG_DIFFERENCE.  Added SEG_EXPR.
	(SEG_NORMAL): Corresponding changes.
	* subsegs.c (seg_name, subsegs_begin): Changed accordingly.
	* write.c (write_object_file): Ditto.
	* config/obj-aout.c (seg_N_TYPE): Ditto.
	* config/obj-bout.c (seg_N_TYPE): Ditto.
	* config/obj-coff.c (seg_N_TYPE): Ditto.
	* config/obj-coffbfd.c (seg_N_TYPE): Ditto.
	* config/obj-vms.c (seg_N_TYPE): Ditto.

	* expr.h (operatorT): Moved in from expr.c, added some values.
	(expressionS): Added X_op field, removed X_seg field; renamed
	X_subtract_symbol to X_op_symbol.
	* expr.c: Extensive changes to assign expression types rather than
	sections and to simplify the parsing.
	* write.c (fix_new_internal): New static function.
	(fix_new): Removed sub_symbol argument.
	(fix_new_exp): New function, takes expression argument.
	* write.h: Prototype changes for fix_new and fix_new_exp.
	* cond.c (s_if): Changed accordingly.
	* read.c (s_lsym, pseudo_set, emit_expr, parse_bitfield_cons,
	parse_repeat_cons, get_segmented_expression,
	get_known_segmented_expression, get_absolute_expression): Ditto.
	* symbols.c (resolve_symbol_value, S_GET_VALUE, S_SET_VALUE):
	Ditto.
	* write.c (write_object_file): Ditto.
	* config/obj-coff.c (obj_coff_def, obj_coff_val): Ditto.
	* config/obj-coffbfd.c (obj_coff_def, obj_coff_val,
	obj_coff_endef, yank_symbols): Ditto.
	* config/obj-elf.c (obj_elf_stab_generic, obj_elf_size): Ditto.
	* config/tc-a29k.c (md_assemble, parse_operand, machine_ip,
	print_insn, md_operand): Ditto.
	* config/tc-h8300.c (parse_exp, colonmod24, check_operand,
	do_a_fix_imm, build_bytes): Ditto.
	* config/tc-h8500.c (parse_exp, skip_colonthing, parse_reglist,
	get_specific, check, insert, md_convert_frag): Ditto.
	* config/tc-hppa.c (the_insn, fix_new_hppa, cons_fix_new_hppa,
	md_assemble, pa_ip, getExpression, getAbsoluteExpression,
	evaluateAbsolute, pa_build_unwind_subspace, pa_entry,
	process_exit): Ditto.
	* config/tc-hppa.h (STAB_FIXUP, is_DP_relative, is_PC_relative,
	is_complex): Ditto.
	* config/tc-i386.c (pe, md_assemble, i386_operand,
	md_estimate_size_before_relax, md_create_long_jump): Ditto.
	* config/tc-i860.c (md_assemble, getExpression, print_insn):
	Ditto.
	* config/tc-i960.c (parse_expr, subs, segs, md_convert_frag,
	get_cdisp, mem_fmt, parse_ldconst, relax_cobr, s_sysproc,
	i960_handle_align): Ditto.
	* config/tc-m68k.c (struct m68k_exp, struct m68k_it, seg, op,
	subs, add_fix, isvar, m68k_ip, md_assemble, md_convert_frag_1,
	md_estimate_size_before_relax, md_create_long_jump, get_num):
	Ditto.
	* config/tc-m88k.c (md_assemble, get_imm16, get_pcr,
	md_create_short_jump, md_create_long_jump): Ditto.
	* config/tc-mips.c (md_assemble, append_insn, gp_reference,
	macro_build, macro, my_getExpression): Ditto.  Also removed
	get_optional_absolute_expression; just use get_absolute_expression
	instead.
	* config/tc-ns32k.c (get_addr_mode, evaluate_expr, convert_iif,
	fix_new_ns32k, fix_new_ns32k_exp, cons_fix_new_ns32k): Ditto.
	* config/tc-ns32k.h (fix_new_ns32k prototype): Ditto.
	* config/tc-sh.c (parse_exp, check, insert, md_convert_frag):
	Ditto.
	* config/tc-sparc.c (md_assemble, sparc_ip, getExpression,
	print_insn): Ditto.
	* config/tc-tahoe.c (struct top, md_estimate_size_before_relax,
	tip_op, md_assemble): Ditto.
	* config/tc-vax.c (seg_of_operand, md_assemble,
	md_estimate_size_before_relax, md_create_long_jump): Ditto.
	* config/tc-z8k.c (parse_exp, check_operand, newfix): Ditto.

Tue Jul 20 12:17:16 1993  david d `zoo' zuhn  ([email protected])

	* configure.in: i386-lynx is the same as i386-coff

Mon Jul 19 15:21:20 1993  Ken Raeburn  ([email protected])

	* config/obj-elf.c (obj_elf_previous): New function.
	(previous_section, previous_subsection): New vars.
	(obj_elf_section): Save current place in case DWARF code wants us
	to pop back to it.  Handle unquoted section name as well as quoted
	section name.  Don't crash on invalid strings.
	(obj_pseudo_table): Handle new pseudos "previous", "2byte", and
	"4byte".

	* config/obj-elf.h: Don't include struc-symbol.h.
	(obj_elf_frob_symbol): Declare arg as struct symbol *.

	* tc-sparc.h (LOCAL_LABEL) [OBJ_ELF]: Local labels can start with
	"L" or "_.L_".

	* write.c (write_relocs): New function, split off from
	write_contents.  Use memset instead of bzero.
	(write_object_file): Apply write_relocs to each section before
	applying write_contents.

	* read.c (read_begin): Call obstack_begin with values closer to 1K
	multiples.
	(read_a_source_file, big_cons, float_cons): Use memcpy instead of
	bcopy.

Mon Jul 19 14:30:00 1993  Ian Lance Taylor  ([email protected])

	* config/tc-m68k.c (m68k_ip_op): Don't decrement strend when
	calculating opP->isiz; this permits the expression size to be
	determined as well, later on.

	* expr.c (clean_up_expression): Don't cancel the subtraction of
	undefined symbols.

	* read.c (s_data), config/obj-coffbfd.c (obj_coff_data): If -R,
	switch to text section rather than data section.

Mon Jul 19 12:35:39 1993  Ken Raeburn  ([email protected])

	* config/tc-m68k.c (m68k_ip, case AINDX): Add 6 to operand
	expression (to take the pc-rel instruction itself into account)
	before using the expression, instead of after.

Fri Jul 16 08:56:04 1993  Ian Lance Taylor  ([email protected])

	* read.c (float_cons): Simplified parsing logic.  If
	REPEAT_CONS_EXPRESSIONS is defined, accept a repeat count.

	* symbols.c (colon): Rather than a special case for TC_HPPA,
	use new macro tc_frob_label.
	* config/tc-hppa.h (tc_frob_label): Define.

	* config/tc-mips.c: Many changes to support simple assembler
	optimization.
	(insn_label, prev_insn, prev_prev_insn, dummy_opcode,
	prev_insn_valid, prev_insn_frag, prev_insn_where,
	prev_insn_fixp, prev_insn_is_delay_slot): New static
	variables.
	(insn_uses_reg, mips_no_prev_insn, mips_emit_delays,
	mips_align, s_stringer, s_mips_space): New static functions.
	(mips_define_label): New global function.
	(md_pseudo_table): For "ascii", "asciz", "asciiz", call
	s_stringer.  Changed argument to float_cons from 0 or 1 to 'f'
	or 'd'.  For "space" call s_mips_space.
	(md_begin): Call mips_no_prev_insn.
	(append_insn): Only insert necessary NOP instructions.
	(macro): Call mips_emit_delays before setting mips_noreorder.
	Increment and decrement mips_noreorder rather than using
	save_reorder_condition.  Don't bother to use noreorder in
	M_L_DOB and M_L_DAB, since append_insn will not insert a NOP.
	(md_atof): Handle floating point numbers correctly for both
	big and little endian targets.
	(s_align, s_cons): Call mips_align rather than frag_align.
	(s_change_seg, s_cons): Call mips_emit_delays.
	(s_float_cons): Let float_cons do the work.
	(s_mipsset): Call mips_emit_delays when setting noreorder.
	* config/tc-mips.h (tc_frob_label): Define to be
	mips_define_label.

	* config/obj-ecoff.c (ecoff_build_symbols, ecoff_build_procs,
	ecoff_frob_files): Consistently use S_GET_VALUE rather than
	bfd_asymbol_value.  Warn if taking difference of symbols in
	different segments.

Thu Jul 15 11:51:03 1993  Ian Lance Taylor  ([email protected])

	* config/obj-ecoff.c (ecoff_frob_file): Discard all open scopes,
	with a warning.

	* config/obj-coffbfd.c (fixup_segment): If TC_M88K, don't adjust
	by md_pcrel_from if we are relocating against a symbol (we still
	need md_pcrel_from for a PC relative relocation within the same
	file).
	* config/tc-m88k.c (md_pcrel_from): Corrected return value.
	(omagic): Removed unused variable.

	* Preliminary support for m88k-coff.
	* configure.in (m88k-*-coff*): New target.  Use coffbfd and
	m88kcoff.
	* config/m88kcoff.mt: New file.
	* read.c (lex_type): New macro LEX_AT to set lex type of '@'.
	(pseudo_set): Handle difference of symbols in different fragments
	by saving the entire expression as the value of the symbol.
	* symbols.c (resolve_symbol_value): Resolve difference
	expressions.
	* config/obj-coffbfd.c (obj_pseudo_table): If TC_M88K, accept
	"sdef" as a synonym for "def".
	* config/obj-coffbfd.h: If TC_M88K, include coff/m88k.h and set
	TARGET_FORMAT.
	(S_IS_LOCAL): Any symbol which includes \001 in the name is local.
	* config/tc-m88k.c, config/tc-m88k.h: Numerous changes to bring
	m88k port up to date, and to add COFF support.

Wed Jul 14 15:09:32 1993  Ian Lance Taylor  ([email protected])

	* Removed sy_forward and replaced it with an undefined expression
	as the value of a symbol.
	* struc-symbol.h (struct symbol): Removed sy_forward field.  Added
	sy_resolved and sy_resolving single bit fields.
	* symbols.c (symbol_new): Don't initialize sy_forward field.
	(resolve_symbol_value): New function to adjust symbol value by
	fragment address, using recursion to resolve forward symbols.
	* symbols.h: Added prototype for new function.
	* read.c (pseudo_set): Set symbolP->sy_value to an undefined
	expression rather than setting symbolP->sy_forward.
	* write.c (write_object_file): Use resolve_symbol_value on
	symbols, keeping the common case (the old behaviour) inline.
	* config/obj-aout.c (obj_aout_frob_symbol): Removed sy_forward
	handling (subsumed by write.c change).
	* config/obj-coff.c, config/obj-coffbfd.c (obj_coff_val): Set
	sy_value rather than sy_forward.
	* config/obj-coffbfd.c (obj_coff_endef, yank_symbols): Check
	expression segment rather than sy_forward.
	(yank_symbols): Use resolve_symbol_value.
	(crawl_symbols): Removed extra pass over symbols.
	* config/obj-aout.c, config/obj-bout.c, config/obj-coff.c,
	config/obj-vms.c (obj_crawl_symbol_chain): Removed extra pass over
	symbols which handled sy_forward; use resolve_symbol_value
	instead.
	* config/obj-coff.h, config/obj-coffbfd.h (obj_frob_forward_symbol):
	Define.
	* config/obj-elf.c (obj_elf_stab_generic): Check expression
	segment rather than sy_forward.
	* config/obj-vms.c (VMS_Check_For_Main): Don't initialize
	sy_forward; do initialize sy_resolved and sy_resolving.
	* config/tc-hppa.h (STAB_FIXUP): Use sy_value, not sy_forward.

	* Changes to keep a full expression as the value of a symbol, not
	just a longword:
	* struc-symbol.h: New field sy_value.
	* as.h: Include expr.h before struc-symbol.h.
	* expr.h: Use struct symbol rather than symbolS.
	* symbols.c (S_GET_VALUE, S_SET_VALUE): Rewrote to retrieve value
	of sy_value field; compile unconditionally, not just if
	BFD_ASSEMBLER.
	* symbols.h: Compile S_{SG}ET_VALUE prototypes unconditionally.
	* write.c (write_object_file): Set BFD symbol value to gas symbol
	value.
	* config/obj-aout.h, config/obj-bout.h, config/obj-coff.h,
	config/obj-coffbfd.h, config/obj-generic.h, config/obj-vms.h
	(S_GET_VALUE, S_SET_VALUE): Removed macro definitions.
	* config/obj-ieee.c (S_GET_VALUE, S_SET_VALUE): Removed.
	* config/obj-coff.h, obj-coffbfd.h: Rewrote several macros to use
	S_GET_VALUE rather than ost_entry.n_value.
	* config/obj-aout.c (obj_symbol_to_chars), config/obj-bout.c
	(obj_symbol_to_chars), config/obj-coff.c (obj_symbol_to_chars),
	config/obj-coffbfd.c (symbol_to_chars): Get value to write out
	using S_GET_VALUE--don't assume it is already set.
	* config/obj-ieee.c (do_symbols): Set BFD symbol value to gas
	symbol value.
	* config/obj-vms.c (various): Don't assign directly to
	S_GET_VALUE; use S_SET_VALUE instead.

Wed Jul 14 09:35:23 1993  Doug Evans  ([email protected])

	* configure.in: Recognize h8300h.

Tue Jul 13 12:09:44 1993  Steve Chamberlain  ([email protected])

	* config/tc-h8500.c (line_comment_chars): Add hash.
	(parse_exp, skip_colonthing, build_bytes): Add support for
	R_H8500_HIGH16 relocation type.

Mon Jul 12 11:15:34 1993  Ken Raeburn  ([email protected])

	* config/obj-elf.c (obj_elf_section): Allow `@' to introduce an
	attribute name.  Handle `execinstr' attribute.

Mon Jul 12 07:22:28 1993  Ian Lance Taylor  ([email protected])

	* config/tc-mips.c (mips_ip): Don't warn on 'i' or 'j' mismatch if
	there is another alternative for the instruction.

Fri Jul  9 17:31:34 1993  Roland H. Pesch  ([email protected])

	* doc/as.texinfo: updates for H8/300H

Thu Jul  8 14:41:43 1993  Mark Eichin  ([email protected])

	* config/tc-i960.c (md_create_short_jump, md_create_long_jump,
	md_number_to_chars, md_section_align): Adjusted to use valueT,
	addressT, to match tc.h.

Thu Jul  8 14:15:05 1993  Ken Raeburn  ([email protected])

	* config/tc-sparc.c (s_common): Revamp to handle both syntaxes,
	independent of format.

Thu Jul  8 07:25:25 1993  Doug Evans  ([email protected])

	* config/tc-h8300.h (TC_CONS_RELOC): Use R_RELLONG if h8/300h.

Wed Jul  7 18:11:07 1993  david d `zoo' zuhn  (zoo at rtl.cygnus.com)

	* configure.in: define CROSS=-DCROSS_COMPILE if it is a cross
	build; also recognize h8300-*-coff

Wed Jul  7 10:21:24 1993  Ian Lance Taylor  ([email protected])

	* symbols.c (fb_label_instance, fb_label_instance_inc): Don't dump
	core just because somebody uses a label before it is defined.

	* config/mips-opcode.h: Moved to opcode/mips.h.
	* config/tc-mips.c: Include opcode/mips.h rather than
	mips-opcode.h.
	(append_insn): An extra NOP is only needed after instructions
	which set HI or LO, not after instructions which read it.
	(macro_build, mips_ip): Support new 'E', 'G' and 'B' arguments.
	(macro): cfc1 and ctc1 now take "t,G" rather than "t,d".
	* config/tc-mips.h (struct mips_opcode): Don't define.
	* config/mips-big.mt, config/mips-lit.mt (TARG_CPU_DEPENDENTS):
	Set to $(srcdir)/../include/opcode/mips.h.

	Get the MIPS assembler up to speed with other gas changes:

	* config/obj-ecoff.c (ecoff_set_vma, ecoff_frob_symbol):
	Removed; don't change the symbol value.
	(ecoff_build_symbols, ecoff_build_procs, ecoff_frob_file): Use
	bfd_asymbol_value rather than S_GET_VALUE to include section
	vma in symbol value.
	(ecoff_frob_file): Ignore BSF_SECTION_SYM symbols, since ECOFF
	doesn't output them.  Set the vma of sections.
	* config/obj-ecoff.h: Don't define obj_frob_symbol.
	* config/tc-mips.c (tc_gen_reloc): Adjustment by section vma is no
	longer necessary.
	(various): use valueT rather than long.

Wed Jul  7 08:33:30 1993  Ken Raeburn  ([email protected])

	* as.h (valueT): Typedef moved here.
	* struc-symbol.h (valueT): ...from here.
	* write.c (write_object_file): Locals from_addr, to_addr,
	table_addr are now addressT.  Supply prototype for bfd_alloc for
	now.
	(fixup_segment): Local add_number is now valueT.  Correct some
	range-checking bugs.
	(relax_align): Type `int' should be sufficient for the exponent.
	(fix_new): Argument offset is type offsetT.  Locals size and
	newsize are type valueT.
	* write.h (struct fix): Fields fx_offset and fx_addnumber are now
	type valueT.
	(fix_new): Fix prototype.
	* symbols.c (symbol_new): Symbol value is type valueT.
	(S_SET_VALUE, S_GET_VALUE): Likewise.
	(S_IS_*): Specify int return type explicitly.
	* symbols.h (symbol_new, S_GET_VALUE, S_SET_VALUE): Fixed
	prototypes.
	* read.c (s_comm): Values read are type valueT.
	* expr.h (expressionS): Field X_add_number is an offsetT.
	* tc.h (md_create_long_jump, md_create_short_jump,
	md_section_align): Addresses are now type addressT.
	(md_number_to_chars, md_apply_fix): Pass value as valueT.
	* config/tc-i386.c (md_create_short_jump, md_create_long_jump,
	md_number_to_chars, md_section_align): Adjusted.
	* config/tc-sparc.c (sparc_ip): Initialize `len' variable to make
	gcc shut up.
	(md_create_short_jump, md_create_long_jump, md_number_to_chars,
	md_section_align): Adjusted.

	* config/tc-sparc.c (s_reserve): Permit use for other than a.out
	format.
	(s_common): Handle Solaris-2 version.

	* config/ho-generic.h (free): Returns void if __STDC__.

	* config/obj-elf.h (obj_elf_frob_symbol, elf_frob_file,
	elf_file_symbol): Declare.

	* expr.c (floating_constant, integer_constant): Now return void.

Thu Jul  1 12:13:43 1993  Ian Lance Taylor  ([email protected])

	* configure.in: Match on sparc*-fujitsu-none rather than
	sparclite*-fujitsu-none.

Wed Jun 30 11:12:02 1993  Ian Lance Taylor  ([email protected])

	* read.c (cons): Conditionalize parsing of expression.  Move
	putting value into object file into separate function.  Separate
	out MRI and WANT_BITFIELDS cases into separate functions.
	(emit_expr): New function to write data into object file.
	Conditionalize on TC_CONS_FIX_NEW and TC_CONS_RELOC rather than on
	processor types.
	(parse_bitfield_cons): New function to parse bitfield expressions
	as used by i960 assemblers.  Only compiled if
	BITFIELD_CONS_EXPRESSIONS is defined.
	(parse_mri_cons): New function to parse MRI style strings.  Only
	compiled if MRI is defined.
	(parse_repeat_cons): New function to parse repeat counts.  Only
	compiled if REPEAT_CONS_EXPRESSIONS is defined.
	* read.h (emit_expr): Added declaration of new function.
	* config/tc-a29k.h (TC_CONS_RELOC): Define to be RELOC_32.
	* config/tc-h8300.h (TC_CONS_RELOC): Define to be R_RELWORD.
	* config/tc-hppa.c (parse_cons_expression_hppa): New function to
	parse a HPPA expression, rather than special case in cons
	function.
	(cons_fix_new_hppa): New function to emit an HPPA fixup, rather
	than special case in emit_expr function.
	* config/tc-hppa.h (TC_PARSE_CONS_EXPRESSION, TC_CONS_FIX_NEW):
	Define to use new functions from tc-hppa.c.
	* config/tc-i960.h (BITFIELD_CONS_EXPRESSIONS): Define.
	(WANT_BITFIELDS): Removed; now obsolete.
	* config/tc-mips.h (REPEAT_CONS_EXPRESSIONS): Define.
	* config/tc-ns32k.c (cons_fix_new_ns32k): New function to emit an
	NS32K fixup, rather than special case in emit_expr function.
	* config/tc-ns32k.h (TC_CONS_FIX_NEW): Define to be
	cons_fix_new_ns32k.  Also use PARAMS rather than checking
	__STDC__.
	* config/tc-sparc.h (TC_CONS_RELOC): Define to RELOC_32.

	* write.c (relax_and_size_seg, adjust_reloc_syms, write_contents):
	Don't core dump if gas has no information about a section.

Wed Jun 30 06:21:27 1993  Ken Raeburn  ([email protected])

	* write.c (relax_and_size_seg): Always fully process a section.
	Section size is last frag's (vm)address plus its size.  If no
	relocations are present, force SEC_RELOC flag clear.
	(dump_section_relocs): New debugging routine.
	(adjust_reloc_syms): New routine, broken out from write_contents.
	Don't adjust relocs that are already relative to section symbol.
	Look for obj_fix_adjustable macro to know what else to skip,
	instead of obj_write_symbol.  Look for section symbol stored in
	section information.
	(write_object_file): Map adjust_reloc_syms over all sections.
	(write_contents): Clear SEC_RELOC flag if no relocations are
	found.

	* as.h (__PTR_TO_INT, __INT_TO_PTR): New versions for Saber, to
	keep it quiet.

	* write.c (remove_subsegs): Don't define for BFD_ASSEMBLER.

Fri Jun 25 14:42:53 1993  K. Richard Pixley  ([email protected])

	* Makefile.in (all, dvi, info, install-info, clean-info): do not
	  echo recursion lines.
	  (install-info, clean-info): collapse into the dvi and info rule.

Fri Jun 25 03:43:06 1993  Ken Raeburn  ([email protected])

	* as.h (strstr): Disable declaration for now.
	(fprint_value, sprint_value): Declare.

	* subsegs.c (subseg_new_rest): Use memset to clear new frag.
	(subseg_new) [BFD_ASSEMBLER]: Initialize all seginfo fields.

	* expr.c (expr_part): Made sanity checks a.out-specific.
	(expr): Disabled sanity checks.

	* subsegs.h (segment_info_type) [BFD_ASSEMBLER]: Add field for
	section symbol.
	* subsegs.c (subseg_change): Initialize section symbol pointer
	when setting up a new section.

	* symbols.c (symbol_new) [BFD_ASSEMBLER]: Point BFD symbol's udata
	field back at gas symbol structure.

	* symbols.c (colon): Cast obstack_next_free value to char* before
	doing arithmetic on it.
	* subsegs.c (subseg_new_rest): Likewise.
	* as.h (frag_now_fix): Likewise.

	* config/obj-elf.c (elf_file_symbol): Use subseg_new instead of
	calling bfd_make_section_old_way directly, and call subseg_set
	instead of subseg_change.  Now returns void.
	(obj_elf_write_symbol): Only check local symbols for now.
	(elf_stab_symbol): Now static and void, and disabled until it
	works completely.
	(obj_elf_size): For expression values, fail silently for now.
	(obj_symbol_new_hook): Do nothing.

	* config/tc-sparc.c (tc_gen_reloc): Handle BFD_RELOC_SPARC_WDISP22
	relocation.
	(s_local) [OBJ_ELF]: New function.
	(md_pseudo_table) [OBJ_ELF]: Call it for "local".
	(s_common): Rearrange to handle Solaris .common pseudo, which may
	sometimes use bss space instead of common.
	* config/obj-elf.h (TARGET_SYMBOL_FIELDS): Add new `local' field.

Thu Jun 24 16:33:53 1993  david d `zoo' zuhn  (zoo at cirdan.cygnus.com)

	* configure.in: set host config to hpux for hppa*-hp-hpux

Thu Jun 24 13:35:06 1993  Ken Raeburn  ([email protected])

	* app.c (app_pop, app_push): Fix bug reported by Chris Arthur.

Tue Jun 22 01:04:23 1993  Ken Raeburn  ([email protected])

	* subsegs.c (subseg_new): Don't special-case a.out -R flag here.
	* config/obj-aout.c (s_sect): Do it here.

	* as.h (BAD_CASE): Don't make some lame compilers think we want
	substitution inside strings.

	* as.c (print_version_id): New function, split off from main.
	(main): Call it.
	* config/tc-sparc.c (md_parse_option) [OBJ_ELF]: Print version id
	for -V.  Ignore -Q and -s options for now.

Mon Jun 21 17:37:59 1993  david d `zoo' zuhn  (zoo at cirdan.cygnus.com)

	* Makefile.in: make installation & builds work again for crosses

Sun Jun 20 18:18:26 1993  Ken Raeburn  ([email protected])

	* listing.c (list_symbol_table): Rewrite to print wide (>32 bits)
	symbol values correctly.

	* write.c (write_object_file): Deleted unused variables.
	(fixup_segment): Use sprint_value.

	* messages.c (sprint_value, fprint_value): New routines.

	* config/obj-elf.c (elf_stab_symbol): Now returns void.
	(obj_elf_stab_generic): Fix typo in logic.

	* Makefile.in (INCLUDES): Look in ../bfd for bfd.h.

	* as.h (addressT, offsetT): New types, using BFD types if
	available.
	(relax_addressT, struct frag): Use them.
	* struc-symbol.h (valueT, struct broken_word): Likewise.

	* as.h (subseg_new) [BFD_ASSEMBLER]: Name argument is const.
	* subsegs.c (subseg_new) [BFD_ASSEMBLER]: Name argument is const.

Thu Jun 17 16:53:56 1993  david d `zoo' zuhn ([email protected])

	* Makefile.in: canonicalize install.sh; for use within
	this directory (and subdirs)

Sun Jun 20 02:34:04 1993  Ashley Saulsbury ([email protected])

	* m88k-opcode.h : fixed tiny tiny mistake - xcr was incorrectly
	specified, should have both S1 and S2 fields identical
	If only finding the problem was as fast as fixing the bug !!!!

Tue Jun 15 16:01:57 1993  Ken Raeburn  ([email protected])

	* write.c (write_contents): Do write out non-loadable sections.
	Debug sections can fall in this category.

	* read.c (s_app_file): Call elf_file_symbol for ELF files.
	* config/obj-elf.c (elf_file_symbol): New function.

	* config/obj-elf.c (elf_stab_symbol_string): Renamed from pa_...,
	added argument to specify section base name.
	(obj_elf_stab_generic): Renamed from ..._stab.  New argument
	specifies section base name.
	(obj_elf_stab): New function, calls obj_elf_stab_generic with
	".stab" as section base name.
	(obj_elf_xstab): New function, calls obj_elf_stab_generic.
	(obj_elf_type): Handle "object".  Use bitwise-or to merge in
	symbol flags rather than simply replacing, so global/local flags
	are preserved.
	(obj_elf_ident): Rewrite.

Tue Jun 15 17:03:25 1993  david d `zoo' zuhn  (zoo at cirdan.cygnus.com)

	* Makefile.in: remove parentdir support; use INSTALL_XFORM

Wed Jun  9 11:26:07 1993  Ian Lance Taylor  ([email protected])

	* config/tc-i386.c (md_pseudo_table): .align uses a power of two
	for any a.out target, not just Linux and 386BSD.
	* config/tc-i386.h (DOT_LABEL_PREFIX): Do not define for any a.out
	target.

Mon Jun  7 13:33:19 1993  Ken Raeburn  ([email protected])

	* config/tc-m88k.c: Don't include flonum.h, md.h, m88k.h.  They
	don't exist or duplicate other inclusions.

	* config/tc-vax.h (NO_RELOC): Define.

Sat Jun  5 19:32:52 1993  Torbjorn Granlund  ([email protected])

	* gas/config/m88k-opcode.h (m88k_opcodes): Add 88110 instructions.
	* gas/config/tc-m88k.c (get_reg): New arg reg_prefix.  Compare first
	char to reg_prefix instead of to 'r'.
	(calcop): Change calls to get_reg.
	(calcop): Handle new case 'x' to set reg_prefix.
	(calcop): Set reg_prefix to 'r' after each call to get_reg.
	(cmpslot): Add 88110 conditions.

	* gas/config/m88k-opcode.h: Swap cases for "rot" for consistency.

	* gas/config/tc-m88k.c (get_bf): Always restore input_line_pointer
	before returning.

	* gas/config/m88k-opcode.h (m88k_opcodes): Make equal mnemonics
	adjacent; mov.s and mov.d swapped.
	(m88k_opcodes): Fix typo `r2' -> `2'.

Fri Jun  4 15:59:31 1993  Steve Chamberlain  ([email protected])

	* config/h8300.c: Support for H8/300-H opcodes.

	* config/obj-coffbfd.c (w_strings): String table length is 4
	bytes, no matter what the host int size is.

	* configure.in (alpha-*-osf*): New.

Fri Jun  4 07:51:18 1993  Ian Lance Taylor  ([email protected])

	* configure.in (mips-*-ecoffl*): New target; use ecoff and
	mips-lit.
	(mips-*-ecoff*): Added trailing '*'.

	* config/obj-ecoff.c (ecoff_build_procs): Force the adr of the
	first FDR in a file to be zero.

Thu Jun  3 14:09:59 1993  Ken Raeburn  ([email protected])

	* Makefile.in (VERSION): Jump to 2.1.4.

	* config/ho-hppabsd.h: New file, from Peter Hoogenboom.

	* config/tc-mips.c (md_assemble): Call bfd_set_gp_size only for
	ECOFF format.

Tue Jun  1 15:21:57 1993  Ken Raeburn  ([email protected])

	* config/tc-m68k.c (md_assemble): The 68040 cpu doesn't want a
	separate '851 mmu.

	* config/obj-elf.c, config/obj-elf.h: Update for new type, macro,
	and routine names.  Assuming 32 bits for now.

	* config/obj-elf.c (elf_frob_file): Look for macro
	elf_tc_final_processing_hook, instead of assuming a function
	always exists.
	* config/tc-hppa.c (elf_hppa_final_processing_hook): Renamed from
	tc_final_processing_hook.
	* config/tc-hppa.h (elf_tc_final_processing_hook): Use it.

	* config/tc-hppa.h (elf_tc_symbol, elf_tc_make_sections): Macros
	moved here from obj-elf.h.
	* config/obj-elf.h: Don't include CPU-specific header files.

Sun May 30 16:49:37 1993  Peter Hoogenboom  ([email protected])

	* configure.in: configurations should match on 'hppa*' not 'hppa'.

	* read.c: Add support for HPPA assembly language syntax (denoted
	with '#ifdef TC_HPPA').

	* symbols.c: Add support for HPPA assembly language syntax (denoted
	with '#ifdef TC_HPPA').

	* write.c (write_contents):  Add support for HPPA-style
	relocations.

	* config/obj-elf.c: Stab symbols weren't written properly.
	(obj_elf_version):
	(obj_elf_desc):
	(obj_elf_write_symbol):
	(obj_elf_write_symbol_p):
	(obj_elf_frob_symbol):
	(elf_stab_symbol):
	(elf_frob_file):

	* config/tc-hppa.c: Support for HPPA symbol extension sections.
	Remove some unused code.  Support for HPPA assembly language
	syntax.

	* app.c:

	* symbols.c:

	* config/obj-elf.h:
	(obj_write_symbol):
	(obj_frob_file):
	(elf_tc_symbol):
	(elf_tc_make_sections):

	* config/tc-hppa.h:

Sun May 30 21:44:45 1993  Ken Raeburn  ([email protected])

	* config/obj-ecoff.c (obj_read_begin_hook, add_file): Assume
	hash_new will have succeeded if it returns.
	* config/tc-a29k.c (md_begin): Likewise.

	* config/tc-i386.c (tc_aout_fix_to_chars): Now nbytes_r_length is
	const.
	(mode_from_disp_size, opcode_suffic_to_type): Now inline under
	gcc.
	(fits_in_{signed,unsigned}_{byte,word}): Likewise.

	* expr.c: Delete register declarations; gcc ignores them anyways.

Fri May 28 19:03:32 1993  Ken Raeburn  ([email protected])

	* hash.c (hash_new): Use xmalloc, since many callers don't check
	for failure.

Thu May 27 13:02:15 1993  Ken Raeburn  ([email protected])

	* frags.c (zero_address_frag, bss_address_frag): These are
	external.

	* tc.h (md_reloc_size): This is const.
	* config/tc-{a29k,h8300,h8500,i386,i860,i960,m68k,ns32k,z8k}.c
	(md_reloc_size): Now const.

	* config/aout_gnu.h (enum machine_type, enum reloc_type): Delete
	trailing commas.
	* as.h (enum _segT): Ditto.

	* struc-symbol.h (N_TYPE_seg): This should be const.

Thu May 27 11:43:59 1993  Michael Meissner  ([email protected])

	* config/obj-ecoff.c (add_file): Cast file_name to char * in
	listing_source_file call.

	* config/obj-elf.c (elf_stab_symbol_string): Cast first argument
	of subseg_new call to eliminate const attribute.
	(obj_elf_stab): Ditto.
	(obj_symbol_new_hook): Cast first argument of bzero call to char *.

	* read.c (s_align_bytes): Properly record alignment.

	* expr.c (__): Undefine __ macro before use, since OSF/1 uses it
	for the prototype/no prototype macro.

	* as.c (got_sig): Don't do return ((SIGTY) 0), SIGTY might well be
	void.

	* as.h (relax_stateT enum): Delete trailing comma.

Thu May 27 11:07:50 1993  Ian Lance Taylor  ([email protected])

	* app.c (do_scrub_begin): Let line_comment_chars override
	comment_chars.
	(do_scrub_next_char): If a line comment character is not at the
	start of a line, treat it as a comment character if it is one.
	For a CPP line comment use pseudo-op .appline rather than .line.
	* input-scrub.c (logical_input_line): Make int rather than
	unsigned.
	(input_scrub_push, input_scrub_begin): Initialize
	logical_input_line to -1 rather than 0.
	(bump_line_counters): Increment logical_input_line.
	(new_logical_line): If line_number is -2, decrement
	logical_input_line.
	(as_where): Use logical_input_line even if it is 0.
	* read.h (s_app_file prototype): Now takes an int argument.
	* read.c (potable): Make .appfile call s_app_file with 1.  New
	.appline pseudo-op calls s_app_line.
	(s_app_file): If .appfile, call new_logical_line with -2 to
	account for newline inserted by do_scrub_next_char.  If listing,
	call listing_source_file.
	(s_app_line): New function to handle fake pseudo-op .appline.
	* config/obj-coff.c (obj_pseudo_table): Make .appline call
	obj_coff_ln.
	(obj_coff_ln): Added argument to indicate whether .appline.
	* config/obj-coffbfd.c (obj_pseudo_table): Make .appline call
	obj_coff_ln.
	(obj_coff_ln): Added argument to indicate whether .appline.
	* config/tc-mips.c (s_file): Pass argument to s_app_file.

Tue May 25 11:59:07 1993  Ian Lance Taylor  ([email protected])

	* config/obj-bout.h (S_GET_VALUE): Removed unnecessary cast.

Thu May 20 19:14:24 1993  Ken Raeburn  ([email protected])

	* config/tc-m68k.c (md_apply_fix_2): Straighten out check for
	invalid values.

Wed May 19 07:33:17 1993  Steve Chamberlain  ([email protected])

	* config/tc-h5000.c (build_bytes): Understand @rd mode and build
	relocations correctly.

Mon May 17 15:06:26 1993  Ken Raeburn  ([email protected])

	* Makefile.in (FLAGS_TO_PASS): Leave out TEXI2DVI for now, because
	it's wrong.

	* config/tc-m68k.c (md_apply_fix_2): Apply range checks and warn
	if value is out of range.

	Patch from Minh Tran-Le:
	* config/tc-i386.c (i386_operand): For in/out port register used
	as base reg, include InOutPortReg in operand type.
	(MATCH): Accept overlap value of InOutPortReg.

Mon May 17 09:29:34 1993  Ian Lance Taylor  ([email protected])

	* config/obj-ecoff.c (add_file, obj_ecoff_loc, obj_ecoff_stab):
	Add calls to listing routines to produce combined source/assembler
	listings.
	(obj_ecoff_stab): Create a file pointer if none used yet.
	(ecoff_frob_file): Set symcount to correct value.

Fri May 14 06:53:33 1993  Ken Raeburn  ([email protected])

	* Makefile.in (VERSION): Bump to version 2.1, in preparation for
	release.

	* config/obj-aout.h (H_GET_HEADER_SIZE, H_SET_SYMBOL_TABLE_SIZE):
	Define in terms of constants, not C structure sizes.

	* config/tc-rs6000.c, config/tc-rs6000.h: Delete empty files.

Thu May 13 17:01:55 1993  Ken Raeburn  ([email protected])

	* config/obj-aout.c (obj_header_append): Don't define if it's
	defined as a macro.
	* config/obj-hp300.h (obj_header_append): Define it as a macro.
	* config/obj-hp300.c (hp300_header_append): New function.

	* Makefile.in (distclean): Don't bother cleaning up doc files;
	they aren't going to be in this directory.

Thu May 13 07:51:35 1993  Ian Lance Taylor  ([email protected])

	* config/obj-ecoff.c (ecoff_build_symbols): Handle absolute
	symbols.

	* tc.h (TC_COFF_SIZEMACHDEP): Don't define here.
	* config/tc-sh.h (TC_COFF_SIZEMACHDEP): Define here instead.

Mon May 10 06:01:12 1993  Ken Raeburn  ([email protected])

	* config/obj-vms.c (VMS_Symbol_type_list): Don't bother with
	initialization.

	* configure.in (targets): Treat m68*-*-sysv* like m68k-*-coff.

Wed May  5 14:00:49 1993  Ian Lance Taylor  ([email protected])

	* config/tc-mips.c (macro): Correct floating point double word
	loads and stores for big endian target.

Wed May  5 08:39:21 1993  Ken Raeburn  ([email protected])

	* config/tc-i386.c: Replace SEG_* with *_section, fix up subseg_*
	calls.  Deleted some unused code.
	* config/obj-coff.c: Likewise.

	ELF support, mostly contributed by Utah:
	* config/obj-elf.c (obj_elf_section, obj_elf_stab, obj_elf_line,
	obj_elf_type): Rewrite.
	(obj_elf_frob_symbol, elf_stab_symbol_string, elf_stab_symbol,
	obj_elf_desc, obj_elf_version, obj_symbol_new_hook, obj_elf_size):
	New functions.
	(obj_elf_ident): Dummy.
	* config/obj-elf.h (FALSE, TRUE, S_*, tc_frob_symbol,
	TARGET_SYMBOL_FIELDS): New macros.
	(gdb_section): New variable decl.

	* config/tc-i386.c (md_atof): Return zero, not empty string, on
	success.

	BFD_ASSEMBLER conditional changes:
	* config/obj-coff.c (lineno_rootP, seg_N_TYPE, *_section_header):
	Don't define these.
	(SA_SET_SYM_ENDNDX, SA_SET_SYM_TAGNDX): New functions.
	(fetch_coff_debug_section): Ditto.
	(obj_coff_endef): Call fetch_coff_debug_section.
	(struct line_no): New type.
	(c_symbol_merge): New way for copying aux fields.
	(c_dot_file_symbol): Put symbol in absolute section, and set flag
	BSF_DEBUGGING.
	(function_lineoff): New symbol.
	(function_lineoff, text_lineno_number, our_lineno_number,
	lineno_lastP): Don't define.
	(c_line_new): Don't define.
	(obj_emit_lineno, obj_coff_endef): Use abort calls as, uh,
	placeholders, until
	line-number recording gets implemented.
	(obj_new_symbol_hook): New code for handling aux fields.
	(add_lineno, add_linesym): New functions.
	(obj_coff_ln): Call add_lineno, not c_line_new.
	(obj_coff_endef): New code for handling symbol names.  New lineno
	code.  Look for section name "*DEBUG*" for debugging section.
	(align, coff_check_file_symbols, obj_coff_section,
	coff_frob_file): New functions.
	* config/obj-coff.h: Reordered some includes.
	(BYTE_ORDERING, FILE_HEADER_MAGIC, seg_N_TYPE, N_TYPE_seg,
	DEFAULT_MAGIC_NUMBER_FOR_OBJECT_FILE, AOUTHDR, AOUTHDRSIZE): Don't
	define these.
	(TARGET_SYMBOL_FIELDS, I960_SYM_FIELDS): New macros.
	(SYM_AUXENT): New macro (for non-BFD_ASSEMBLER too) for accessing
	aux entries.  Most SA_* macros now use it unconditionally.
	(S_*): Use `bsym' field, and access BFD private data.
	(SF_*): Use `sy_flags' symbol field for most of these.
	(H_*, object_headers, lineno, lineno_*P, OBJ_EMIT_LINENO): Don't
	define.
	(*_section_header): Don't define.
	* config/tc-i386.c (md_convert_frag, md_apply_fix): Changed
	interface.
	(tc_gen_reloc) [I386COFF]: New function.
	(tc_aout_fix_to_chars, tc_coff_fix2rtype): Don't define.
	* config/tc-i386.h (TARGET_ARCH, TARGET_BYTES_BIG_ENDIAN): New
	macros.

	* config/obj-coff.c (stack_init): Don't do assignments inside
	conditions.
	(obj_coff_def): Simplified handling of symbol name a bit.
	(tag_insert): Name argument is now pointer to CONST.
	(obj_crawl_symbol_chain): Commented out.

	* config/obj-coff.h: Use PARAMS macro in prototypes.

	* write.c (relax_and_size_seg) [BFD_ASSEMBLER]: Don't indirect
	through frchainP pointer if it is null.

	* configure.in: Warn if BFD mode is explicitly turned off but is
	required by specified target.
	(mips ecoff targets): Don't need to set bfd_gas here; it gets
	taken care of later.

	* config/obj-coffbfd.c (crawl_symbols): Don't clear sy_forward
	field.
	(yank_symbols): Merge symbols only if sy_forward is null.

	* config/tc-m68k.h (AOUT_MACHTYPE): Don't define if already
	defined.

	* tc.h (md_convert_frag) [BFD_ASSEMBLER]: Section arg is not
	pointer.
	* config/tc-m68k.c (md_convert_frag) [BFD_ASSEMBLER]: Ditto.

	* config/tc-sparc.h (LOCAL_LABEL) [OBJ_ELF]: Anything starting
	with "." is a local label.

	* config/te-hppa.h, config/tc-hppa.h, config/tc-hppa.c: New config
	files.

	* config/te-linux.h, config/te-386bsd.h: New config files.
	* configure.in (i386-*-linux, i386-*-bsd): Use them.
	* config/tc-i386.h (TARGET_FORMAT): Select format based on target
	environment.
	(DOT_LABEL_PREFIX): Don't define for 386bsd or Linux.

Wed May  5 13:14:01 1993  Ian Lance Taylor  ([email protected])

	* config/obj-ecoff.c (init_file): Set fMerge to 0 since dbx seems
	to want it that way.
	(ecoff_build_symbols): Turn local st_Proc symbols into
	st_StaticProc symbols.  Set index field of external st_Proc and
	st_staticProc symbols correctly.
	* config/tc-mips.h (NO_LISTING): Don't define.  People might want
	listings.

Tue May  4 21:22:54 1993  Ken Raeburn  ([email protected])

	* config/obj-hp300.h, config/obj-hp300.c, config/te-hp300.h: New
	files.
	* configure.in (m68k-*-hpux): Use them.

	* config/obj-aout.c (obj_pre_write_hook): Use AOUT_VERSION if
	defined, otherwise zero.

	* config/aout_gnu.h (OMAGIC): Don't define if already defined.

Mon May  3 15:59:32 1993  Steve Chamberlain  ([email protected])

	* config/tc-sparc.c (sparc_ip): Allow any abs expression as an
	address space number.

Wed Apr 28 19:11:22 1993  Ken Raeburn  ([email protected])

	* config/obj-aout.h (TARGET_DEFAULT): Don't default this at all.

	* config/tc-a29k.c: Include ctype.h.
	(define_some_regs): Added special-purpose registers for 29050.

	* config/tc-i386.c (comment_chars) [TE_I386AIX]: Include "/".

	* config/obj-coffbfd.c (fill_section): Don't set STYP_REG here.
	(change_to_section): Set it here instead.

Wed Apr 28 13:40:29 1993  Ian Lance Taylor  ([email protected])

	* config/obj-ecoff.c (obj_symbol_new_hook): Make up a .file if one
	hasn't been seen yet.
	(add_ecoff_symbol): Don't refer to cur_file_ptr if it is NULL.

Mon Apr 26 18:29:05 1993  Steve Chamberlain  ([email protected])

	* config/tc-sh.ch, config/tc-sh.h: New files supporting Hitachi
	SH.

Mon Apr 26 12:28:27 1993  Ian Lance Taylor  ([email protected])

	* expr.c (operand): Fix unary plus operator (previously was the
	same as '~' operator!).

Wed Apr 21 00:20:11 1993  Ken Raeburn  ([email protected])

	* write.c (cvt_frag_to_fill): Define even if BFD is defined.
	(write_object_file): Do define if BFD_ASSEMBLER.  Invoke
	obj_check_file_symbols if defined.  Call verify_symbol_chain_2
	instead of open-coding it.  Fix some bugs in patching up symbol
	chain.
	(relax_segment): Make some code we "ought to be able to" use for
	all targets no longer conditionalized on ns32k target; instead, do
	it always, and if the appropriate conditions fail, abort.

	* symbols.c (DEBUG): Enabled.
	(symbol_new): Make sure bfd_make_empty_symbol works.
	(verify_symbol_chain_2): New funcion; takes one symbol as
	argument, anywhere in the chain.
	(dollar_label*): Use default initializers.

	* as.c (perform_an_assembly_pass): Call md_begin here...
	(main): ...and not here.

	* config/tc-m68k.h (TARGET_FORMAT): Use a.out-sunos-big for a.out.
	(tc_frob_symbol): New macro: Get rid of symbols in reg_section.

	* config/tc-m68k.c (omagic): Don't define for BFD_ASSEMBLER.
	(add_fix, add_frag): Now functions instead of macros.
	(m68k_reg_parse, m68k_ip, md_estimate_size_before_relax, get_num,
	s_data1, s_data2, s_bss): Use new *_section names, for
	compatibility with BFD_ASSEMBLER mode; rewrite switch statements
	to handle non-integral segT.
	(tc_coff_fix2rtype, tc_aout_fix_to_chars,
	tc_coff_symbol_emit_hook): Don't define for BFD_ASSEMBLER.
	(tc_gen_reloc): New routine for BFD_ASSEMBLER.
	(md_apply_fix, md_apply_fix_2): Renamed old md_apply_fix to
	md_apply_fix_2; new md_apply_fix definition varies interface
	depending on BFD_ASSEMBLER.
	(md_convert_frag, md_convert_frag_1): Likewise.  Use new *_section
	names.

	* config/obj-vms.c: Include config.h.
	(version_string): Delete declaration.
	(Write_VMS_MHD_Records): Use GAS_VERSION instead.
	(vms_resolve_symbol_redef): New function, taken from VMS code in
	symbols.c.
	(_doprnt): Deleted.
	(VMS_Store_Struct, VMS_Def_Struct, VMS_Set_Struct,
	VMS_TBT_Block_End, get_VMS_time_on_unix, generate_suffix,
	VMS_Psect_Spec): Fixed to compiler under traditional C.
	* config/obj-vms.h: Use PARAMS macro.
	(vms_resolve_symbol_redef): Declare.
	(RESOLVE_SYMBOL_REDEFINITION): New macro.
	* symbols.c (colon): Remove some VMS-specific code, look for
	RESOLVE_SYMBOL_REDEFINITION macro instead.

	* config/tc-m68k.c (m68k_ip): Don't try expanding DBcc
	instructions.

	* config/tc-i386.c: Reordered some functions so inlining might
	work.  Use PARAMS in function declarations.
	(reloc): New routine.
	(md_assemble): Rearrange switch statements to work with
	non-integral segT.

	* struc-symbol.h [BFD_ASSEMBLER]: Undefine
	SYMBOLS_NEED_BACKPOINTERS before defining it.

	* subsegs.c (subseg_new_rest): Now static.

	* read.c (pseudo_set): Better error message for difference of
	symbols in different frags.

	* Makefile.in (check): Pass down some new variables, indicating
	pathname or program name for cc, nm, objdump.

	* as.h (OUTPUT_FLAVOR): New macro.
	* config/tc-sparc.c (tc_gen_reloc): Use OUTPUT_FLAVOR.

	* configure.in: Initialize bfd_gas properly.  Warn that ELF
	support is incomplete.

Thu Apr 15 22:39:05 1993  Ken Raeburn  ([email protected])

	* read.c (float_cons): Accept null pointer return from md_atof.
	* config/tc-m68k.c (md_atof): Return null for success.
	* config/tc-sparc.c (md_atof): Ditto.

Thu Apr 15 16:04:39 1993  Roland H. Pesch  ([email protected])

	* doc/as.texinfo: formatting and comment cleanups; show SPARC
	alternative options in same style as other machines; simplify some
	conditional use; include GPL as separate file (from texinfo dir)

	* doc/Makefile.in: (as.info) include directory containing GPL in
	makeinfo search path

	* doc/h8.texi: new file; conditional settings for GAS manual
	on Hitachi chips

Tue Apr 13 15:31:40 1993  Roland H. Pesch  ([email protected])

	* doc/as.texinfo: mention SPARC architecture options.

Fri Apr  9 17:43:11 1993  Ken Raeburn  ([email protected])

	* configure.in: Rearranged whitespace in per-host/per-target
	sections.  Added hooks for dropping in HPPA support (not included
	yet).  Separate out overrides of variables based on target format
	and bfd-gas selection from actual target-specific commands.  Add
	error message for recognized but unsupported format name.

Fri Apr  9 09:05:47 1993  Ian Lance Taylor  ([email protected])

	* config/obj-ecoff.h (ecoff_build_lineno): Make ilineMax in
	symbolic header match cline in FDR; the native linker seems to
	want that.

Thu Apr  8 15:51:28 1993  david d `zoo' zuhn  (zoo at cirdan.cygnus.com)

	* doc/Makefile.in: as.texinfo is in $(srcdir).  Use
	$(srcdir)/as.texinfo explicitly in several places

Thu Apr  8 15:15:02 1993  Roland H. Pesch  ([email protected])

	* doc/Makefile.in: update dvi, clean targets for new source
                           file structure

Thu Apr  8 12:52:46 1993  Ian Lance Taylor  ([email protected])

	* config/ho-decstatn.h: Define BROKEN_ASSERT if not __GNUC__,
	rather than undefining know.
	* configure.in: Match ultrix*, not just ultrix.

Wed Apr  7 20:18:10 1993  Roland H. Pesch  ([email protected])

	* doc/as.texinfo: converted conditional markup to use new
	Texinfo facilities, avoiding m4.

	* doc/as-all.texinfo, all.m4, pretex.m4: deleted.

	* doc/Makefile.in: recast doc configuration to use a link to an
	included texinfo file.

	* doc/all.texi: settings for generic form of documentation.

Tue Apr  6 11:56:21 1993  Ian Lance Taylor  ([email protected])

	* read.c (cons): Zero out frag when creating reloc.

Mon Apr  5 09:41:58 1993  Ian Lance Taylor  ([email protected])

	* config/tc-mips.c (gp_reference): Certain magic symbols can never
	be referenced off the GP register.

	* app.c (do_scrub_next_char): Handle states 9 and 10 correctly
	when dealing with characters of type LEX_IS_TWOCHAR_COMMENT_1ST,
	LEX_IS_STRINGQUOTE, and LEX_IS_ONECHAR_QUOTE.

	* config/te-irix.h: New file; irix needs a different LOCAL_LABEL
	definition from other MIPS targets.
	* configure.in (mips-*-irix): Use emulation irix.

Sun Apr  4 15:21:09 1993  Steve Chamberlain  ([email protected])

	* config/tc-h8500.c: Get relax size of branch instructions right,
	(get_operand): Parse @sp+ correctly.

Fri Apr  2 15:59:49 1993  Ken Raeburn  ([email protected])

	* subsegs.h (segment_info_type) [BFD_ASSEMBLER]: Don't include
	COFF section header field.

	* configure.in: Print error message if host or target is not
	supported.

	* configure.in: If with-bfd-assembler, use obj-coff instead of
	obj-coffbfd.

	* config/ho-generic.h: Include string.h.

Fri Apr  2 08:54:57 1993  Ian Lance Taylor  ([email protected])

	* config/tc-mips.h (LOCAL_LABEL): Treat any label starting with
	'$' as local, for any object file format.

	* config/tc-mips.c (macro): Optimizations to branching code and a
	couple of bug fixes from [email protected] (Ralph
	Campbell).

	* config/ho-irix.h: New file; if not gcc, define BROKEN_ASSERT.
	* configure.in (mips-sgi-irix*): Set gas_host to irix.

Wed Mar 31 17:53:54 1993  Ian Lance Taylor  ([email protected])

	* subsegs.c (subseg_new): Set output_section of new section.
	* as.c (perform_an_assemly_pass): Don't set output_section here.
	* expr.c (expr_part, expr): Turn off section assertions for ECOFF,
	since it has additional sections.
	* read.c (s_lcomm): For MIPS ECOFF, put small objects in .sbss,
	not bss_section.
	* config/obj-ecoff.h (TARGET_SYMBOL_FIELDS): Added
	ecoff_undefined field.
	* config/obj-ecoff.c (obj_symbol_new_hook): Initialize
	ecoff_undefined field.
	(add_file): If using stabs, just output a stabs symbol rather than
	creating a new fdr.
	(obj_ecoff_begin, obj_ecoff_bend): Ignore line number by reading
	it with get_absolute_expression, rather than skipping it by hand.
	(obj_ecoff_loc): If using stabs, just output a stabs symbol rather
	than ECOFF line number information.
	(obj_ecoff_stab): Accept non-zero values for stabs line number.
	(ecoff_build_symbols): Set ifilesym correctly.  Set storage class
	to small, undefined and/or readonly sections if appropriate.
	Don't output symbol names containing \001 characters.
	(ecoff_frob_file): Make sure at least one fdr is output.
	* config/tc-mips.h: Define TC_MIPS.
	* config/tc-mips.c (g_switch_value): New static variable.
	(md_assemble): Set gp size of output BFD.
	(gp_reference): New function; returns 1 if expression can be
	accesssed via gp.  Always returns 0 if not using ECOFF.
	(macro_build): Convert BFD_RELOC_LO16 to BFD_RELOC_MIPS_GPREL if
	possible.
	(macro): Generate sequences using gp if possible.
	(md_parse_option): Ignore -EL and -EB.  Parse -G.
	(md_apply_fix): Added BFD_RELOC_MIPS_GPREL to ignored case.
	(s_change_sec): Handle .rdata and .sdata for ECOFF.
	(s_extern): Mark symbol as external.  Set ecoff_undefined field.

Tue Mar 30 10:11:41 1993  Ken Raeburn  ([email protected])

	* output-file.c (output_file_create): Don't call as_perror for
	filename rejected by application.

	* as.c (main) [BFD_ASSEMBLER]: If errors occur, close and unlink
	the output file.

	* doc/as.texinfo: Don't use @value in node names for the moment;
	references don't appear to work right.

	* as.h (const, volatile): Put these definitions back, and use
	them.

	* doc/as.texinfo: First pass at using new texinfo features --
	variables, conditional tests.  Far from complete.

Mon Mar 29 16:05:40 1993  Ken Raeburn  ([email protected])

	* read.c: Temporary hack to handle some 64-bit constants.  This
	should be redone later.
	(target_big_endian): Declare.
	(big_cons): If it's set, reverse order of bytes being copied.
	* config/tc-sparc.c (md_begin): Set target_big_endian.

	* read.c (s_ignore): Delete declaration of is_end_of_line.

	* config/obj-coffbfd.c (yank_symbols): Build list of file symbol
	forward pointers properly.

Mon Mar 29 13:47:33 1993  Steve Chamberlain  ([email protected])

	* config/obj-coffbfd.c (do_relocs_for): Fix bug where nrelocs
	wasn't being stored into scnhdr.
	* config/obj-coffbfd.h: Add prototype of s_get_segment.
	* read.c (TC_START_LABEL): Default definition.
	(read_a_source_file): Use TC_START_LABEL macro to work out
	if a label has been seen.

Mon Mar 29 12:56:56 1993  Ian Lance Taylor  ([email protected])

	* configure.in: Set BFDDEF and BFDLIB at the top of Makefile, not
	the bottom (make expands variables in dependencies when the
	dependencies are read, not when they are used).

	* config/obj-coffbfd.c (fill_section): Don't set NOLOAD bit for
	a29k .bss section; the mondfe program doesn't like it.

Sun Mar 28 08:12:53 1993  Ken Raeburn  ([email protected])

	* config/tc-m68k.c: Use PARAMS macro, and use CONST instead of
	const.
	(current_architecture): Don't need initializer.

Fri Mar 26 08:12:48 1993  Ken Raeburn  ([email protected])

	* doc/none.m4: Define Z8000.
	* doc/Makefile.in (as-*.texinfo): Refer to $(srcdir).  Remove the
	texinfo file before recreating it.
	(TEXI2DVI): Need to set TEXINPUTS if "make as.dvi" is to work in
	this directory.
	(srcdir): Delete second, bogus definition.
	(as.info): Look for as-*.texinfo in current directory rather than
	in $(srcdir).
	(as.dvi): Ditto.
	(dvi): New rule.
	* doc/configure.in: Create links to all as-*.texinfo files in the
	source directory, if that's not the current directory.

	* configure.in (per-host):  Accept MIPS host with BSD version
	number.
	(per-target): Classify i486 as i386.  Use generic cpu_type instead
	of target_cpu in selecting format etc.

	* app.c (do_scrub_next_char): Use .appfile, not .app-file.
	* read.c (potable): Change .app-file to .appfile.

	* config/ho-decstatn.h: Renamed from ho-decstation.h.
	* configure.in: Adjusted.

	* config/obj-bfd-sunos.*: Unused; deleted.

	* Makefile.in (version.c, vers-stamp): Deleted.
	(config.h): Define GAS_VERSION.
	* as.c (version_string): Deleted declaration.
	(main): Look for GAS_VERSION instead.

	* doc/as.texinfo: Updated description of -a* (listing) options,
	and describe how to pass them through from gcc.

	* config/obj-coffbfd.c (do_relocs_for): Don't allocate storage or
	process relocs if there aren't any relocs to process.  Avoids
	malloc/free bug on SCO too.

	* as.h: Move local include files below system include files, to
	avoid some redefinition complaints on some systems.
	(const, volatile): Don't need these conditionally defined if we
	use CONST and VOLATILE from ansidecl.h.
	(seg_name): Use CONST, not const.

Fri Mar 26 10:22:04 1993  Ian Lance Taylor  ([email protected])

	* config/tc-mips.c: Reindented to GNU standards.

Thu Mar 25 08:59:14 1993  Ian Lance Taylor  ([email protected])

	* config/obj-coffbfd.c (do_relocs_for): Remove a29k special case.
	(fixup_segment): Add a29k special case; the linker is not prepared
	to see a segment offset here.

	* app.c (do_scrub_next_char): Added new state, 10, modifying state
	9 to only keep a space in between identifier characters.

Wed Mar 24 02:16:22 1993  david d `zoo' zuhn  (zoo at poseidon.cygnus.com)

	* Makefile.in: add dvi target; as-$(config).texinfo might live in
	srcdir, might be in objdir.

	* doc/Makefile.in: dvi depends on as.dvi

Mon Mar 22 23:59:13 1993  david d `zoo' zuhn  (zoo at cirdan.cygnus.com)

	* Makefile.in: add installcheck target

Mon Mar 22 10:19:00 1993  Ian Lance Taylor  ([email protected])

	* config/tc-mips.c (macro): Use $AT for any floating point load.

Sat Mar 20 12:50:51 1993  Ken Raeburn  ([email protected])

	* config/tc-m68k.c (m68k_ip): For operand type 'M', reject
	bignums, but don't emit error message.

Fri Mar 19 21:02:19 1993  Jim Wilson  ([email protected])

	* Makefile.in (targ-cpu.o): Depend on config.h.

Wed Mar 17 16:44:06 1993  Ian Lance Taylor  ([email protected])

	* app.c (do_scrub_next_char): Added new state, 9, to avoid
	dropping a space immediately following an identifier.
	* expr.c, write.c: Rewrote assert expressions to not use multiple
	lines; I don't think that can be done portably.
	* config/tc-mips.c (macro): Use $AT if target register is zero in
	load instruction, which it can be for a floating point load.

Mon Mar 15 12:17:28 1993  Ian Lance Taylor  ([email protected])

	* write.c (write_contents): Compute the relocs before writing out
	the section contents.
	* config/obj-ecoff.h, config/obj-ecoff.c: Numerous changes to get
	symbol table and values right.
	* config/tc-mips.h (LOCAL_LABEL): If OBJ_ECOFF, any label starting
	with $L is local.
	* config/tc-mips.c (tc_gen_reloc): If OBJ_ECOFF, adjust the addend
	by the section vma.

	* config/z8k.mt (TARG_CPU_DEPENDENTS): The relevant file is
	z8k-opc.h, not z8k.h.

	* config/obj-coffbfd.c (obj_coff_endef): Correct test for .bf
	symbol.

Fri Mar 12 18:33:36 1993  david d `zoo' zuhn  (zoo at cirdan.cygnus.com)

	* configure.in: recognize sparc-sun-solaris2* instead of -solaris2

Fri Mar 12 12:00:07 1993  Ian Lance Taylor  ([email protected])

	* expr.c, write.c: Ultrix native 4.2 cc requires assert condition
	to be on a single line.

Thu Mar 11 17:56:22 1993  Ken Raeburn  ([email protected])

	* Makefile.in (config.h): Create file, writing out definitions of
	target cpu, alias, and canonical name.
	(ALL_CFLAGS): No longer define TARGET_CPU.

	* Makefile.in (check): Print a message, instead of quitting
	silently.

	* as.c (main): Don't catch any signals, for now.

	* version.c: Deleted.
	* Makefile.in: Generate it, putting in only the version number
	itself.
	(VERSION): New variable.
	* as.c: Include config.h.
	(main): Reformatted version string.  Include target alias.  Don't
	print if not requested (i.e., unknown -v argument).

	* as.c (stralloc): Deleted.
	(main): Call strdup instead.

	* configure.in: Handle all 68300 series chips.
	* config/tc-m68k.c: Include config.h.
	(md_assemble): Assume TARGET_CPU is defined.  Accept some 68300
	series cpus as defaults.
	(md_parse_option): Accept some m68300 series CPUs as defaults.

Wed Mar 10 17:41:16 1993  Ken Raeburn  ([email protected])

	* as.c (EXIT_SUCCESS, EXIT_FAILURE): Define to normal values if
	not already defined.
	(main, got_sig): Use them.
	* config/ho-vms.h (EXIT_SUCCESS, EXIT_FAILURE): Reverse default
	values.

Tue Mar  9 07:40:06 1993  Ian Lance Taylor  ([email protected])

	* config/obj-ecoff.c, config/obj-ecoff.h: Preliminary ECOFF
	support.

	* config/tc-mips.h (TARGET_FORMAT): Define based on OBJ_AOUT vs.
	OBJ_ECOFF as well as TARGET_BYTES_*_ENDIAN.
	(struct loc, struct proc, struct file): Moved to tc-mips.c within
	#ifndef OBJ_ECOFF block, since ECOFF uses different versions.
	* config/tc-mips.c: Rearranged for ECOFF support.  Added
	prototypes for all static functions.  Moved existing minimal
	debugging format support info #ifndef OBJ_ECOFF blocks.
	(macro_build_lui): Eliminated sign_extend argument, because ECOFF
	does not support a non sign extended high 16 bits reloc.  Adjusted
	all callers accordingly.
	(tc_get_register): Renamed from get_register, and made non-static.

	* config/mips-big.mt, config/mips-lit.mt: New files.  Define
	TARGET_BYTES_BIG_ENDIAN and TARGET_BYTES_LITTLE_ENDIAN,
	respectively.
	* configure.in (mips-*-bsd*): Use gas_target mips-lit.
	(mips-*-ultrix*, mips-*-irix*, mips-*-ecoff): New targets, using
	obj_format ecoff and gas_target mips-lit or mips-big.

Tue Mar  9 07:43:01 1993  Ken Raeburn  ([email protected])

	* version.c: Bump to version 2.0.1.

Tue Mar  9 07:40:06 1993  Ian Lance Taylor  ([email protected])

	* write.c (chain_frchains_together): Check that seg_info (section)
	is not NULL.
	(write_object_file): Call obj_frob_file after setting the symbols,
	not before.

Tue Mar  9 00:00:00 1993  Ken Raeburn  ([email protected])

	* Version 2.0 released.

Mon Mar  8 14:57:10 1993  Ken Raeburn  ([email protected])

	* config/tc-i386.h (TC_COUNT_RELOC): Look for fx_addsy only.

Fri Mar  5 09:05:55 1993  Ian Lance Taylor  ([email protected])

	* read.h: Define stringer here.
	read.c, config/obj-ieee.c, config/obj-tcm88k.c: Not any of these
	places.

Thu Mar  4 11:52:23 1993  Steve Chamberlain  ([email protected])

	* read.c (s_space): Multiply repeat count by mult, not fill.

Thu Mar  4 05:20:42 1993  Ken Raeburn  ([email protected])

	* read.c: Include ctype.h.

Wed Mar  3 10:41:46 1993  Ken Raeburn  ([email protected])

	Patches from Eric Youngdale:
	* make-gas.com: Find obstack.obj if it's not in the current
	directory.
	* read.c (s_ignore): Don't declare is_end_of_line.  It's
	redundant, and triggers a VMS gcc compiler bug.

	* write.c (write_object_file): Macro SUB_SEGMENT_ALIGN now takes
	current segment as an argument.  (Ignored in all cases but VMS.)
	All callers and definitions changed.

Tue Mar  2 11:56:19 1993  Ian Lance Taylor  ([email protected])

	* listing.c: Cleaned up a bit, added prototypes, made NO_LISTING
	case compile again.

Tue Mar  2 08:53:34 1993  Ken Raeburn  ([email protected])

	* config/tc-m68k.c (isbyte): Accept all values from -255 to +255,
	so "~0x80" won't be rejected.

	* config/obj-elf.c: No longer include elf/reloc.h.
	(obj_elf_section): Set SEC_READONLY and SEC_CODE for text section.
	(obj_elf_stab, obj_elf_desc): Deleted do-nothing and commented-out
	routines.
	(obj_elf_xstab): New routine.
	(obj_elf_set_size): Call as_warn, not fprintf.  Pass desired
	argument to s_ignore.  Put "#if 0" around unused code.
	(obj_pseudo_table): Use s_ignore instead of do-nothing routines.
	Call elf_xstabs for .stabs and .xstabs operators.

	* config/tc-sparc.h (TARGET_FORMAT) [OBJ_ELF]: Now "elf32-sparc".

	* write.c (relax_and_size_seg): Set SEC_RELOC only if fixups are
	present.

	* configure.in: mips-bsd configuration was missing format spec.
	Should use aout.

	* Makefile.in (Makefile): Depends on configure.in.

	* config/tc-mips.c (append_insn): Don't check for alignment of
	frag in memory; alignment of instructions in section is a separate
	matter.

	* config/tc-mips.c (macro_build_lui): Fix some assumptions of ANSI
	C availability.

	* listing.h: Always provide function declarations, not macros, so
	pcc won't lose.

Tue Mar  2 00:50:43 1993  John Gilmore  ([email protected])

	* CONTRIBUTORS:  Update Gilmore entry.

Wed Feb 24 14:58:19 1993  Ken Raeburn  ([email protected])

	* frags.c (frag_init): New function.
	(zero_address_frag, bss_address_frag): Now initialized at run
	time.
	* as.c (main): Call frag_init.

Wed Feb 24 10:32:42 1993  Ian Lance Taylor  ([email protected])

	* app.c (do_scrub_next_char): In LEX_IS_LINE_COMMENT_START case:
	Don't unget ch2 if we didn't get it.

Wed Feb 24 04:14:07 1993  Ken Raeburn  ([email protected])

	* doc/Makefile.in (TEXIDIR): Updated for new layout.

	* config/tc-sparc.c (s_common): Add support for ELF version.
	(tc_gen_reloc) [BFD_ASSEMBLER]: New function.
	* config/tc-sparc.h (TARGET_ARCH, TARGET_FORMAT) [BFD_ASSEMBLER]:
	New macros.
	(md_convert_frag): New macro.

	* config/tc-m68k.c (m68k_ip): For PC-relative addressing of a
	symbol, fix the offset so "+2" isn't required.

	* config/tc-i960.c (line_comment_chars, line_separator_chars):
	Define as common/bss.
	(op_hash, reg_hash, areg_hash, iclasses_seen, br_cnt): Default C
	initializers are sufficient.

	* config/obj-aout.h [BFD_ASSEMBLER]: Include libaout.h from bfd.
	(TARGET_FORMAT) [BFD_ASSEMBLER]: Default to "a.out".
	(S_SET_*, S_GET_*, obj_frob_symbol) [BFD_ASSEMBLER]: New macros.
	(S_SET_TYPE) [!BFD_ASSEMBLER]: New macro.
	* config/obj-aout.c: Use PARAMS macro for declarations.  Remove
	"IGNORE_DEBUG" conditional, since both branches are identical.
	Use S_SET_TYPE, S_GET_TYPE, and S_GET_DESC instead of directly
	referencing symbol structure members.
	(obj_aout_frob_symbol) [BFD_ASSEMBLER]: New function.

	* as.h (struct frag): Reordered a couple of fields for better
	packing.

	* write.c (record_alignment) [BFD_ASSEMBLER]: Record it in the
	section info.
	(write_contents) [BFD_ASSEMBLER]: New function.
	(write_object_file) [BFD_ASSEMBLER]: Always handle -R here.  Call
	fix_new with BFD_RELOC_NONE instead of 0 or NO_RELOC.  Call
	obj_frob_file, obj_frob_symbol, tc_frob_symbol if defined.
	(fixup_segment): Make sure common-section symbols get treated the
	same as undefined symbols.
	(fix_new) [BFD_ASSEMBLER]: Argument r_type is of type
	bfd_reloc_code_real_type.  Use seg_fix_{root,tail}P derived from
	section info.
	* write.h (fix_new): Update prototype.

	* tc.h (md_operand, md_convert_frag, tc_headers_hook,
	md_section_align, md_undefined_symbol): Don't provide prototypes
	if these are defined as macros.
	(md_convert_frag) [BFD_ASSEMBLER]: BFD version needs bfd and
	section passed.

	* symbols.c (symbol_new): Argument NAME is now pointer to const.
	Simplified STRIP_UNDERSCORE code.  Remove assumptions about null
	pointers in freshly allocated storage. 	[BFD_ASSEMBLER]: Get new
	BFD symbol.
	(colon): Display other/desc fields of redefined symbol only if
	S_GET_OTHER and S_GET_DESC are defined.
	(symbol_make): Argument NAME is now pointer to const.
	(symbol_find, symbol_find_base): Likewise.
	(S_IS_*, S_GET_*, S_SET_*) [BFD_ASSEMBLER]: New functions.
	* symbols.h: Fix prototypes for new const arguments.  Add
	prototypes for BFD_ASSEMBLER S_* functions.

	* subsegs.c (subseg_change) [BFD_ASSEMBLER]: BFD version of code
	for changing to an existing section.
	(subseg_new_rest) [BFD_ASSEMBLER]: Split off from subseg_new,
	called by subseg_new and subseg_set.
	(subseg_new) [BFD_ASSEMBLER]: Rewritten to change to new section,
	given section name and subseg number.
	(subseg_set) [BFD_ASSEMBLER]: New function; change to a possibly
	new section/subsection.

	* read.c: Don't include ctype.h.
	(cons) [BFD_ASSEMBLER]: For undefined symbols, use BFD_RELOC_32
	for now; should be machine-dependent.

	* configure.in: Accept *-*-elf and *-*-solaris* as ELF format
	targets, forcing BFD use.

Wed Feb 17 18:59:03 1993  Ken Raeburn  ([email protected])

	* config/tc-sparc.c: Use PARAMS macro for static function
	declarations.  Use BFD_RELOC_ macros everywhere, with
	compatibility macros declared for non-BFD mode.
	(struct sparc_it) [BFD_ASSEMBLER]: Use bfd_reloc_code_real_type
	instead of enum reloc_type.
	(emit_sparc_reloc): Commented-out function deleted.
	(md_convert_frag): Deleted.
	(tc_aout_pre_write_hook): Don't define for BFD_ASSEMBLER.
	(md_apply_fix): Changed calling sequence (conditionally) for BFD
	version.
	* config/tc-sparc.h (md_convert_frag): New macro.

	* config/obj-aout.c (obj_aout_stab): Refer to undefined_section,
	not SEG_UNKNOWN.  Use S_SET_TYPE, S_GET_TYPE, S_GET_DESC instead
	of referencing fields directly.

	* write.c (cvt_frag_to_fill): New function; extracted from
	write_object_file.
	(write_object_file) [! BFD_ASSEMBLER]: Call it.
	(relax_and_size_seg) [BFD_ASSEMBLER]: New function; relax section
	and set its size and flags.

	* struc-symbol.h (struct symbol) [BFD_ASSEMBLER]: Replace some
	fields with BFD equivalents.  Turn on back-pointers, and add
	target-specific fields at end.

Thu Feb 11 09:20:37 1993  Ian Lance Taylor  ([email protected])

	* config/obj-coffbfd.c (fill_section): Don't set vaddr here.
	(write_object_file): Set it here instead, so that fixup_segment
	can see the correct value.

Mon Feb  8 13:56:17 1993  Ken Raeburn  ([email protected])

	* write.c (write_object_file): Check for errors and warnings and
	bail out before processing contents.
	(chain_frchains_together_1): New function, does most of the work
	of remove_subsegs.
	(chain_frchains_together) [BFD_ASSEMBLER]: New function.
	(remove_subsegs) [! BFD]: Call it.
	(write_object_file) [BFD_ASSEMBLER]: Converted to use BFD
	structures and routines.

	* config/obj-elf.*: New files.

	* config/mips.mt, config/rs6000.mt: Deleted.

	* config/h8300.mt: Don't specify compiler here.

	* config/z8k.mt: The z8k code depends on the z8k opcode table,
	not the h8300 one.
	* config/tc-z8k.h: Comment fix.

	* write.c: Reordered some functions for better inlining.
	(fixup_segment): Linkrelax code is no longer conditional on
	TC_I960.

Thu Feb  4 12:45:16 1993  Steve Chamberlain  ([email protected])

	* config/{h8500.mt, tc-h8500.c, tc-h8500.h, obj-coffbfd.c,
	obj-coffbfd.h}: support for the H8/500

Wed Feb  3 19:28:18 1993  Ken Raeburn  ([email protected])

	* config/obj-vms.h (SUB_SEGMENT_ALIGN): Define VMS version here.
	* write.c (write_object_file): Not here.
	(fix_new): Initialize fx_addnumber.

	* listing.c: Don't include target-cpu.h explicitly, since as.h
	includes it.

Thu Jan 28 00:35:40 1993  Ken Raeburn  ([email protected])

	* write.h [BFD_ASSEMBLER]: Don't declare next_object_file_charP,
	*_fix_root, *_fix_tail, seg_fix_rootP, seg_fix_tailP.
	(struct fix): Reordered fields for compactness and efficiency.
	Converted some logical fields to 1-bit fields.

	* config/obj-aout.h: Use PARAMS.
	[BFD_ASSEMBLER]: Don't define/declare AOUT_MACHTYPE, seg_N_TYPE,
	N_TYPE_seg, DEFAULT_MAGIC_NUMBER_FOR_OBJECT_FILE.

	* read.c: Don't include listing.h; as.h includes it.  Removed
	DONTDEF code.
	[BFD_ASSEMBLER]: Include subsegs.h.
	(old_buffer, new_broken_words): Default initialization is
	sufficient.

	* output-file.c [BFD_ASSEMBLER]: Include bfd.h, default TARGET_MACH
	to 0, define stdoutput.
	(output_file_create) [BFD_ASSEMBLER]: Call bfd_perror on failure.
	Call bfd_set_arch_mach.
	(output_file_close) [BFD_ASSEMBLER]: Call bfd_close, not
	bfd_close_all_done.  Call bfd_perror on failure.
	(output_file_append) [BFD_ASSEMBLER]: Don't define.

	* config/m68kcoff.mt (LOCAL_LOADLIBES): Delete definition.

	* subsegs.h (segment_info_type): Always define.  Omit field scnhdr
	if not MANY_SEGMENTS.  Define new field bfd_section if
	BFD_ASSEMBLER.
	(seg_info): New macro.

	* expr.c, input-scrub.c: Use PARAMS macro.  Deleted unused
	variables, and some irrelevant comments.

	* Makefile.in (ALL_CFLAGS): Include $(BFDDEF).
	(LIBS): Include $(BFDLIB).  Don't bother with $(CLIB).
	* configure.in:  Permit --with-bfd-assembler now, with a warning.
	Variable need_bfd is now a boolean, as is new variable bfd_gas.
	Set BFDDEF and BFDLIB in Makefile when appropriate.

	* as.c: Removed "#ifdef DONTDEF" and "#ifdef comment" code.
	(main): Refer to flag_always_generate_output instead of
	flagseen['Z'].

	* as.c (main) [BFD_ASSEMBLER]: Open output bfd.
	(*_section) [BFD_ASSEMBLER]: Define them.
	(perform_an_assembly_pass) [BFD_ASSEMBLER]: Initialize them, and
	set section flags when appropriate.
	* as.h (SEG_NORMAL) [BFD_ASSEMBLER]: Require that the specified
	section is not absolute, undefined, or an assembler internal one.
	(absolute_section, undefined_section): Always define.
	* expr.c, read.c, symbols.c: Refer to *_section, not SEG_*; break
	switch statements into if-else trees.
	* symbols.c [MANY_SEGMENTS]: Deleted redundant definitions of
	SEG_BSS and SEG_DATA.

	* as.h (frag_now_fix): New macro.
	* symbols.c (colon): Use it.

Wed Jan 27 21:43:53 PST 1993  Ralph Campbell  ([email protected])

	* config/tc-mips.c:  Added mips support for mips-dec-bsd.
	* config/tc-mips.h:  Added mips support for mips-dec-bsd.
	* config/ho-mipsbsd.h:  Added mips support for mips-dec-bsd.
	* config/mips-opcode.h:  Added mips support for mips-dec-bsd.
	* configure.in:  Added mips support for mips-dec-bsd.
	* atof-generic.c:  Define TRUE and FALSE if not defined.

Thu Jan 21 12:48:19 1993  Ken Raeburn  ([email protected])

	* version.c: Bumped version number to 1.93.05.

Wed Jan 20 17:11:53 1993  Ken Raeburn  ([email protected])

	* config/obj-coff.c (obj_emit_relocations): Don't use #elif.
	(obj_emit_lineno): Don't need return at end of void function.
	(obj_symbol_new_hook): Ditto.

	* config/tc-m68k.c: Removed some unused code.
	(tc_aout_fix_to_chars): Array nbytes_r_length is now const.

	* config/tc-m68k.h (TC_COUNT_RELOC): Don't emit reloc if only
	offset field is set.

Fri Jan  8 05:44:49 1993  Ken Raeburn  ([email protected])

	* config/tc-sparc.c (architecture_requested, warn_on_bump,
	md_relax_table): Use default zero initialization.
	(s_reserve): Since SEG_E2 is equivalent to SEG_BSS, just use the
	latter, instead of selecting with preprocessor conditionals.

Thu Jan  7 08:58:21 1993  david d `zoo' zuhn  (zoo at cirdan.cygnus.com)

	* configure.in: recognise all sparclite variants

Thu Jan  7 05:25:25 1993  Ken Raeburn  ([email protected])

	* read.c (s_data) [!BFD_ASSEMBLER]: Fix typo in 4 Jan change --
	accidentally changed to use subseg_change where it should have
	been subseg_new.

Tue Jan  5 08:42:16 1993  Ken Raeburn  ([email protected])

	* expr.c (operand): If character other than comma or newline is a
	logical end-of-line character, use the newline case.
	From Eric Youngdale:
	(operand): Set X_add_number field for floating-point numbers.
	(operand): Treat zero byte as end-of-operand.

	* configure.in (per-target): Look for with_bfd_assembler option.
	For now, only accept "no", until the merge is done.

	Merged changes from Eric Youngdale ([email protected]):
	* as.c, flonum-konst.c, hex-value.c, input-file.c, version.c,
	  config/obj-aout.h, config/obj-vms.c: VMS -> HO_VMS.
	* read.c: Finish conversion to S_* macros in the VMS only
	  parts of the program. Add "const" modifier to hex_value.
	* as.c, read.c, symbols.c, write.c: Change "ifdef VMS" to
	  "ifdef OBJ_VMS".
	* expr.c: Add "const" modifier to hex_value.
	* symbols.c: Finish conversion to S_* macros in the VMS only
	  parts of the program.  Add "const" modifier to
	  md_[long,short]_jump_size. Remove declaration of const_flag
	  (which will be declared in obj-vms.h).
	* write.c: Add "const" modifier to md_[long,short]_jump_size.
	  Fix arguments to VMS_write_object_file.
	* config-gas.com: New file.  Script for VMS systems to set up the
	  configuration to build gas for VMS, and create config.status.
	* make-gas.com: Redone to work with new scheme.
	* obj-vms.c: Patch to fix bug where we were not correctly parsing the
	  stabs directives.
	* obj-vms.c:  Define macros COPY_LONG and COPY_SHORT which
	  will swap bytes if needed on a big endian system.  Use throughout
	  as needed.
	* obj-vms.c (obj_aout_stab):  Add code to generate listing file.
	* obj-vms.c (VMS_typedef_parse): Add alias to correctly handle certain
	  types of malformed stabs.  Change parsing algorithm so that we are
	  more certain of having all of the information that we need on hand.
	* obj-vms.c (final_forward_reference):  New function, used to help
	  resolve the data types of as many struct elements as possible
	  when some part of the struct is not fully defined by the compiler.
	* obj-vms.c (VMS_LSYM_Parse):  Correctly handle case of continuation
	  stabs directives.
	* obj-vms.c (VMS_write_object_file): Define all vtable psects
	  as symbols as well in the object file.  Look for external functions
	  that start with "__vt.", and turn them into variables, since the
	  g++ compiler is incapable of doing this.
	* tc-vax.c: Add '1' option for backward compatibility with older GCC
	  versions.
	* bignum-copy.c (bignum_copy): Fix bug where we pad with zeroes.
	* input-scrub.c (as_where): Fix bug where as would crash if we did not
	  have the name of the source file yet.
	* config/ho-vms.h: define HO_VMS, not HO_VAX.

Mon Jan  4 05:17:26 1993  Ken Raeburn  ([email protected])

	* read.c (s_data): Always use "data_section", since it'll map to
	SEG_DATA or SEG_E1 if needed.
	(s_lcomm): Likewise with bss_section.
	(s_fill): Use memset, not bzero.

Thu Dec 31 04:29:27 1992  Ken Raeburn  ([email protected])

	* read.c: Deleted some code under "#ifdef DONTDEF" that was for
	handling GDB symbol table data.

	* config/obj-aout.h (segment_name): Delete definition.
	(seg_name): Delete declaration.
	* config/obj-bout.h (segment_name, seg_name): Ditto.
	* config/obj-vms.h (segment_name, seg_name): Ditto.
	* config/obj-coff.h (segment_name): Ditto.
	* config/obj-coffbfd.h (segment_name): Ditto.

	* Changes for BFD_ASSEMBLER:
	* obj.h (obj_crawl_symbol_chain): Declare only if not
	BFD_ASSEMBLER.
	(obj_header_append, obj_pre_write_hook): Ditto.
	* as.h (stdoutput): New var, defined only if BFD_ASSEMBLER.
	(segT) [BFD_ASSEMBLER]: New typedef for "asection *".
	(segment_name) If BFD_ASSEMBLER, look up BFD section name;
	otherwise, use seg_name array.
	(seg_name): Declare only if not BFD_ASSEMBLER.
	(section_alignment): Declare only if not BFD_ASSEMBLER.
	(big_section, reg_section, pass1_section, diff_section,
	absent_section, text_section, data_section, bss_section): If
	BFD_ASSEMBLER, declare as variables; otherwise, declare as macros,
	mapping to segT enum values.
	(tc_aout_fix_to_chars, next_object_file_charP): Force parse errors
	if these are used or defined, if BFD_ASSEMBLER.
	(subseg_set, subseg_new) [BFD_ASSEMBLER]: Functionality of old
	subseg_new split into two functions.
	(SEG_NORMAL): For BFD_ASSEMBLER, always return true, for now.

	* as.h (volatile): Don't define if already defined.
	(had_errors, had_warnings): Provide prototypes for ANSI C even if
	NO_STDARG.
	(as_bad, as_fatal, as_tsktsk, as_warn): For GNU C version 2,
	declare with format attribute for -Wformat checking.

Wed Dec 30 10:18:57 1992  Ian Lance Taylor  ([email protected])

	* app.c, config/tc-*.c: Don't include read.h, since it is already
	included by as.h.

	* These are based on patches from Minh Tran-le
	<[email protected]>.
	* configure.in (i[34]86-ibm-aix*): Accept i486 for host.  Use
	obj_format coffbfd and gas_target i386coff for target.
	(i[34]86-*-isc*): New host (uses sysv).
	* config/i386aix.mt: Removed (no longer used).
	* config/mh-i386aix (RANLIB): Use true rather than /bin/true.
	(MINUS_G): Removed.
	(LDFLAGS): Added, defined as -shlib.
	* config/te-i386aix.h (REVERSE_SORT_RELOCS): Undefine.
	* config/te-sco386.h (LOCAL_LABEL): Don't define.
	(DOT_LABEL_PREFIX): Define.
	* expr.c (operand): If DOT_LABEL_PREFIX, use .L0\001 as a label
	name rather than L0\001.
	* read.c (s_lcomm): Make a frag in SEG_BSS rather than using
	local_bss_counter.
	* symbols.c, symbols.h (local_bss_counter): Removed.
	* write.c (write_object_file): bss no longer uses
	local_bss_counter.  Pass correct data and bss size to
	VMS_write_object_file.
	* config/obj-vms.c (VMS_write_object_file): Accept bss size as
	argument, rather than using local_bss_counter.
	* config/tc-m88k.c (s_bss): Don't use local_bss_counter.
	* config/tc-sparc.c (s_reserve): Don't use local_bss_counter.
	* config/obj-coffbfd.c (had_lineno, had_reloc): Removed.
	(size_section): Restored sanity check.
	(do_relocs_for): Base section address on s_paddr rather than
	computing it.  Adjust a29k R_IHIHALF special case to account for
	section paddr (used to require paddr to be zero).  If there are no
	reclos, set s_relptr to 0.  Set relocation size in object_headers.
	(fill_section): Always set s_vaddr here, removing
	ZERO_BASED_SEGMENTS case.  Force s_scnptr for bss to 0.  Don't set
	NOLOAD for i386 .bss, because it confuses the SVR3 native linker.
	Set STYP_INFO for .comment.
	(coff_header_append): Use object headers and H_{SET,GET}_* macros.
	Make aouthdr writing depend on OBJ_COFF_OMIT_OPTIONAL_HEADER.
	(crawl_symbols): Handle 8 character section name correctly.  Use
	H_{SET,GET}_* macros.
	(do_linenos_for): Set lineno size in object_headers.
	(write_object_file): Use H_{SET,GET}_* macros.  Don't bother to
	set s_vaddr here.  If string_byte_count remains 4, set it back to
	0, and only write strings out if there are some.  Call
	fill_section before do_relocs_for and do_linenos_for.
	(obj_coff_section): Handle optional quoted second argument giving
	section characteristics.
	(obj_coff_bss): Added to handle .bss.
	(obj_coff_ident): Added to handle .ident (puts string in .comment
	section).
	(obj_coff_lcomm): Put common symbols in .bss, not .data.
	(fixup_mdeps): Change to segment.  Call frag_wane after
	md_convert_frag.
	(fixup_segment): Explicitly check S_IS_COMMON before making 386
	adjustment (already happened only for common symbols, but this is
	clearer).
	* config/obj-coffbfd.h (OBJ_COFF_OMIT_OPTIONAL_HEADER): Define.
	* config/tc-i386.c (s_bss): Don't use if I386COFF.
	(md_pseudo_table): Ignore .optim and .noopt.
	(tc_coff_sizemachdep): New function.
	* config/tc-i386.h (REVERSE_SORT_RELOCS): Undef, for SVR3
	compatibility.
	(LOCAL_LABEL): Removed definition.
	(DOT_LABEL_PREFIX): Defined.

Mon Dec 28 10:32:05 1992  Ken Raeburn  ([email protected])

	* app.c (app_push): Use memcpy, not bcopy.
	(do_scrub_next_char): For \", return " not '.
	(symbol_chars): Now const.

	* expr.c (operand): If not LOCAL_LABELS_FB, don't look for "0f"
	and "0b".  If LOCAL_LABELS_DOLLAR, check for "0$".

	* config/obj-coff.h: Don't use #elif.

	* config/ho-sunos.h: Don't include sys/stdtypes.h; 4.0.3 doesn't
	have it.  (Reported by Noah Friedman, [email protected].)

Wed Dec 16 12:12:33 1992  Ian Lance Taylor  ([email protected])

	* write.c, obj-ieee.c: don't define SUB_SEGMENT_ALIGN if it is
	already defined.

Tue Dec 15 12:40:11 1992  Steve Chamberlain  ([email protected])

	* app.c (do_scrub_begin): allow single quote strings if so
	configured.

	* config/*z8k*: checkpoint

Sun Dec 13 00:04:38 1992  Ian Lance Taylor  ([email protected])

	* read.c (read_a_source_file): avoid calling xmalloc (0).

Sat Dec 12 15:26:34 1992  Ian Lance Taylor  ([email protected])

	* listing.c: Call xmalloc, not malloc; don't declare malloc.

	* Changes to support SCO 3.2v4:
	* read.c (s_align_bytes, s_align_ptwo): If not SEG_DATA or
	SEG_BSS, fill with NOP_OPCODE.
	* config/i386coff.mt: Add opcode/i386.h to TARG_CPU_DEPENDENTS.
	* config/obj-coffbfd.c (do_relocs_for): Increment addr even if not
	using ZERO_BASED_SEGMENTS.
	(fill_section): If ZERO_BASED_SEGMENTS, set segment addresses, but
	never set segment address for SEG_E2 (.bss) and don't write out
	SEG_E2 contents.  Set .init and .fini sections to STYP_TEXT.
	(obj_coff_endef): Don't merge labels or symbols awaiting forward
	definitions, and don't merge tags with non-tags.  Check for .bf
	rather than just checking whether the second character is b and
	the third character is f.
	(obj_coff_val): gcc can generate values which we don't handle
	correctly; discard information for now, since it only affects the
	debugging information.
	(tag_find_or_name): Don't insert tags in the symbol table.
	(yank_symbols): Don't merge labels.
	(write_object_file): Don't define SUB_SEGMENT_ALIGN if it is
	already defined.  Fill subsegments with NOP_OPCODE, not 0.  Don't
	set segment address if ZERO_BASED_SEGMENTS.
	(obj_coff_section): Accept and ignore a trailing quoted string, as
	used in AT&T i386 syntax.
	(fixup_segment): Take segment as argument.  On the i386, adjust PC
	relative addends by the segment vaddr.
	* tc-i386.h: Define SUB_SEGMENT_ALIGN.
	* tc-a29k.h: Define ZERO_BASED_SEGMENTS.
	* tc-i386.c: (i386_operand): If I386COFF, accept any segment type.

Tue Dec  8 00:06:48 1992  Ken Raeburn  ([email protected])

	* config/obj-coffbfd.c: Include libcoff.h.

	* version.c: Now version 1.93.

Mon Dec  7 00:39:09 1992  Ken Raeburn  ([email protected])

	* config/tc-i386.c (md_pseudo_table): For 386bsd and linux, do
	power-of-two alignment for .align.

	* as.h: If BROKEN_ASSERT, just redefine `assert' to be trivial,
	and leave everything else alone.

Fri Dec  4 16:58:42 1992  Ken Raeburn  ([email protected])

	* Makefile.in (as.new): Don't bother saving as.old.

	* write.c: Conditionalize on OBJ_VMS, not VMS.
	(magic_number_for_object_file): Don't define if OBJ_VMS.

	* config/obj-vms.c: Changes for traditional C.

Thu Dec  3 01:24:07 1992  Ken Raeburn  ([email protected])

	* config/ho-generic.h (malloc, realloc): Declare.

	* Lots of comment/whitespace changes.

	* write.h (struct fix): Some fields reordered, narrowed.

	* read.c (MASK_CHAR): Define using C types, not magic number.

	* as.c, input-file.c: Deleted some unused code.

	* app.c, as.h: Doc fix.

	* flonum-konst.c, flonum-mult.c: Include ansidecl.h.

	* as.h (xmalloc): Argument is long.

	* xmalloc.c (error): Remove declaration; as.h takes care of it.

	* doc/as.texinfo: Regrouped documentation of some command-line
	options.  Updated options documentation for m68k.  Some minor
	wording/punctuation changes.

Mon Nov 30 11:42:11 1992  Ken Raeburn  ([email protected])

	* configure.in: Accept target OS "vms".

	* symbols.c:  Merged ANSI and non-ANSI function decls, using
	PARAMS macro.

	* xmalloc.c: Just include as.h, don't bother trying to figure out
	other header files.

	* strstr.c, strerror.c: Deleted.
	* Makefile.in: Deleted references.

	* config/tc-ns32k.c: Don't include header file for string
	declarations; leave that to ho-*.h.

Fri Nov 27 04:11:36 1992  Ken Raeburn  (raeburn at cambridge-laptop.cygnus.com)

	* config/coff_gnu.h [TC_I860]: Guesses for reloc type values,
	imported from FSF sources.

	* messages.c (strerror): Declare unconditionally.

	* as.h: Delete alloca and register definitions.

	* config/atof-ieee.c (mask): Now const.

	* obstack.c, obstack.h: Deleted.

	* as.h (flag_readonly_data_in_text): New flag.
	* as.c (main): Set it for -R.

	* as.h (flag_suppress_warnings): New flag.
	* as.c (main): Set it for -W.
	* messages.c (as_warn): Check it instead of flagseen['W'].

	* as.h (flag_always_generate_output): New flag.
	* as.c (main): Set it for -Z.

	* config/tc-sparc.h: Define NEED_FX_R_TYPE.
	* config/tc-a29k.h: Ditto.
	* write.h (struct fix): Don't conditionalize fx_r_type field on TC
	macros.

	* as.h: Merged ANSI and non-ANSI function decls, using PARAMS
	macro.
	* bignum.h, expr.h, flonum.h, frags.h, input-file.h, listing.h,
	obj.h, output-file.h, read.h, struc-symbol.h, symbols.h, tc.h,
	write.h: Likewise.
	* read.c: Likewise.

	* xmalloc.c: Conditionalize on HAVE_MALLOC_H, not USG.  Fold in
	xrealloc from xrealloc.c.
	* xrealloc.c: Deleted.
	* Makefile.in (REAL_SOURCES, OBJS): Adjusted.

	* configure.in: For host CPU a29k, rs6000, vax, consider using bsd
	or vms ho- files.

	* config/ho-sysv.h (setbuffer, HO_USG): Deleted.

	* config/atof-ieee.c (atof_ieee): Exponent field isn't a pointer;
	don't initialize it with NULL.

	* config/ho-vax.h (M_VAX): Deleted; was unused.

	* README-vms, config/ho-vms.h, config/obj-vms.c, config/obj-vms.h:
	New files imported from FSF version, contributed by Eric Youngdale.
	* README-vms-dbg, config/vms: Deleted.

	* ChangeLog, config/ChangeLog: Merged.

	* config/*tahoe*, configure.in: Tahoe support brought in from FSF
	version.

	* input-file.c (input_file_open): Eliminate call to setvbuf.
	[USG] (setbuffer): Deleted macro.

Mon Nov 23 11:00:16 1992  Ken Raeburn  ([email protected])

	* all files: Whitespace changes for GNU indentation style, done by
	GNU `indent'.  Some cleanup still needed, especially of comments.

	* configure.in: No te-386bsd.h file exists; don't try to use it.

	* obj-coff.c (obj_coff_endef): Use as_warn, not fprintf.

	* tc-m68k.c (md_assemble): Don't complain about 68000 with 68881;
	could be doing emulation.

Thu Nov 19 11:47:19 1992  Steve Chamberlain  ([email protected])

    	z8000 documentation
	* doc/Makefile.in, doc/all.m4, doc/as-all.texinfo, doc/as.texinfo:
	all modified.

Tue Nov 10 09:49:24 1992  Ian Lance Taylor  ([email protected])

	* Makefile.in (as.o, obj-format.o): added dependency on subsegs.h.

	* subsegs.h: add extern to segment_info declaration.

	* read.h: added extern declarations for comment_chars,
	line_comment_chars, and line_separator_chars.
	read.c, app.c: removed definitions of comment_chars,
	line_comment_chars, and line_separator_chars.

	* tc-m68k.c (m68k_reg_parse): If REGISTER_PREFIX isn't defined,
	still accept (but don't require) OPTIONAL_REGISTER_PREFIX before
	the register name.
	(insert_reg): put REGISTER_PREFIX before register names before
	putting them in the symbol table.
	* tc-m68k.h (OPTIONAL_REGISTER_PREFIX): Define to be "%", if not
	M68KCOFF.

	* obj-coffbfd.c (fill_section): set STYP_NOLOAD bit for .bss
	section.

	* atof-ieee.c, atof-ns32k.c, tc-*.c: made EXP_CHARS, FLT_CHARS,
	comment_chars, line_comment_chars and line_seperator_chars
	consistently const, and always initialized them.  Included read.h.

Thu Nov  5 17:55:41 1992  Jim Wilson  ([email protected])

	* tc-sparc.c (sparc_ip): Add code to flag error if an absolute
	constant will not fit in an immediate field.
	(md_apply_fix, RELOC_BASE13 case): Check for relocation overflow.

Wed Nov  4 07:50:46 1992  Ken Raeburn  ([email protected])

	* obj-coff.c (callj_table): Delete global variable.
	(obj_emit_relocations): Define it locally here, and only if
	TC_I960 is defined.

	* tc-m68k.c (m68k_reg_parse): Underscore is part of a symbol name.
	(m68k_ip): Don't warn about bignum used as float bit-pattern.

	* obj-coff.c: Replaced ANSI and non-ANSI function declarations
	with a single set using PARAMS macro.

	* tc-i960.c (tc_bout_fix_to_chars): Bit-field fixups want a length
	of 2.

	* tc-i960.c: Missed a couple of 0->NO_RELOC conversions.

	* tc-i960.h (N_BALNAME, N_CALLNAME): Define as char-type values,
	so widening works consistently.

Wed Oct 28 08:52:34 1992  Ken Raeburn  ([email protected])

	* version.c: Put conditional "const" before version_string, not
	before dummy function for VMS.  Now version 1.91.03.

	* app.c (do_scrub_next_char): Need double-\ before `000' to show
	printed rep of null character.

Fri Oct 23 14:40:38 1992  Ian Lance Taylor  ([email protected])

	* obj-coffbfd.c (write_object_file): check return value of
	bfd_close_all_done.

Tue Oct 20 12:18:08 1992  Ian Lance Taylor  ([email protected])

	* Support for i386-sysv.
	obj-coffbfd.c (do_relocs_for, write_object_file): set segment
	addresses to reasonable sizes.  New define ZERO_BASED_SEGMENTS can
	be used to set them all to zero as was done before.
	(fill_section): segment addresses now set in write_object_file.
	(fill_section): Don't set STYP_NOLOAD for .bss section.
	(fixup_segment): 386 uses strange common symbol format.
	tc-i386.c (tc_coff_fix2rtype): use R_DIR32, not R_RELLONG, for
	compatibility with SVR3.2 linker.
	* configure.in: i386-sysv and i386-sco use coffbfd.

	* app.c (do_scrub_next_char): discard whitespace after a label.

Sat Oct 10 12:33:45 1992  david d `zoo' zuhn  (zoo at cirdan.cygnus.com)

	* configure.in: differentiate between SunOS 4 and Solaris2 for Sun4
	hosts, use the sysv configuration for solaris2

Mon Oct  5 09:28:57 1992  Steve Chamberlain  ([email protected])

	 fix i960+non-bfd coff bit rot.
	* obj-coff.c (c_dot_file_symbol, obj_coff_ln, obj_coff_line):
	support for C source listings. (obj_coff_endef): look in the right
	part of the symbol for the symbol name

	* tc-m68k.c (get_num): make it work for all segments, not just the
	first three.

Mon Oct  5 03:30:36 1992  Mark Eichin  (eichin at tweedledumber.cygnus.com)

	* configure.in:	recognize i386-*-bsd emulation.

Thu Oct  1 23:05:12 1992  david d `zoo' zuhn  (zoo at cirdan.cygnus.com)

	* configure.in: use the cpu-vendor-os triple for host and target

Tue Sep 29 12:22:52 1992  Steve Chamberlain  ([email protected])

	* obj-coffbfd.c (write_object_file): don't fixup for the z8k
	* tc-z8k.c: lots of bug fixes

Tue Sep 29 10:51:55 1992  Ian Lance Taylor  ([email protected])

	* tc-i960.h, tc-i960.c: avoid the ANSI preprocessor addition
	#elif, since it is not supported by old compilers.
	ho-rs6000.h, tc-m68k.c: the native RS/6000 compiler miscompiles a
	couple of expressions in tc-m68k.c.

Mon Sep 28 21:18:24 1992  Ken Raeburn  ([email protected])

	* read.c (cons): If NO_RELOC is defined, use it.

	* tc-i960.c (get_cdisp): Use NO_RELOC, not 0, in call to fix_new.

Fri Sep 25 18:18:52 1992  Ian Lance Taylor  ([email protected])

	* tc-m68k.h: if M68KCOFF, define DOT_LABEL_PREFIX (to require
	local labels to start with a .) and set REGISTER_PREFIX to %.
	tc-m68k.c (m68k_reg_parse): accept REGISTER_PREFIX if defined.

Fri Sep 25 17:53:43 1992  John Gilmore  ([email protected])

	* messages.c:  Comment changes.

Fri Sep 25 14:12:58 1992  Ken Raeburn  ([email protected])

	* as.h: Test if __STDC__ is defined only, don't test its value.
	* messages.c: If __STDC__ is not defined, define NO_STDARG.

Thu Sep 24 12:42:32 1992  Brendan Kehoe  ([email protected])

	* listing.c (debugging_pseudo): Add stabs and stabn as things to
	ignore.

Tue Sep 22 13:02:07 1992  Sean Eric Fagan  ([email protected])

	* obj-coffbfd.c (do_relocs_for,fill_section): now allocate all
	sections starting from zero, rather than making them consecutive.
	This makes subsequent reloc calculations easier, esp if the object
	format doesn't understand addends. (obj_coff_lcomm): (maybe temporarily)
	allocate lcomm in .data rather than in .bss.  It seems that some
	tools can't cope with a non-zero sized bss before linkage.

Tue Sep 22 15:10:51 1992  Ken Raeburn  ([email protected])

	* tc-m68k.c: Replace "enum m68k_architecture" with "int"
	throughout.  That enum no longer means what we thought it meant.

	* tc-m68k.c (md_assemble, md_parse_option): Handle new
	"-mno-688[58]1" options.

	* tc-m68k.c: Added CPU32 support.

Fri Sep 18 08:02:18 1992  Steve Chamberlain  ([email protected])

	* tc-m68k.c (m68k_ip): An(disp) is not pc relative.

Tue Sep 15 17:25:05 1992  Jim Wilson  ([email protected])

	* Makefile.in (as.new): Remove dependence on LOCAL_LOADLIBES.
	Change LIBDEPS dependence to LIBS.

Tue Sep 15 15:32:02 1992  Ian Lance Taylor  ([email protected])

	* Makefile.in (install): if $(tooldir) exists, install as in
	$(tooldir)/bin.

Sun Sep 13 20:30:10 1992  Ian Lance Taylor  ([email protected])

	* Added WARN_SIGNED_OVERFLOW_WORD define to give an error if any
	.word is < -32768 or > 32767.  The -J flag causes the error to be
	ignored.  This is to catch over-sized switches generated by gcc on
	systems which don't support the broken .word hack.
	as.c (main): permit -J if WARN_SIGNED_OVERFLOW_WORD.
	write.c (fixup_segment): check for signed .word overflow if
	WARN_SIGNED_OVERFLOW_WORD.

	* write.c (fixup_segment): fixed missing parens in expression
	checking for byte or word overflow.

	* obj-coffbfd.h: define WARN_SIGNED_OVERFLOW_WORD.
	obj-coffbfd.c (fixup_segment): check for signed .word overflow if
	WARN_SIGNED_OVERFLOW_WORD.

	* obj-coffbfd.c (fixup_segment): fixed missing parens in
	expression checking for byte or word overflow.

Fri Sep 11 10:21:04 1992  Steve Chamberlain  ([email protected])

	Support for i386 coff
	* obj-coffbfd.h : added stuff
	* tc-i386.c (tc_coff_fix2rtype): new function
	* tc-i386.h : new coff defines

Thu Sep 10 09:23:15 1992  Ian Lance Taylor  ([email protected])

	* input-scrub.c (input_scrub_push): call input_file_begin, not
	input_scrub_begin.
	messages.c (as_perror): print ": " between the passed in error and
	the strerror, like perror does.

Wed Sep  9 11:06:25 1992  Ian Lance Taylor  ([email protected])

	* Makefile.in: use gas_target instead of modifying target_cpu.
	From Steve Chamberlain:
	Makefile.in: Handle m68*-*-coff*.
	read.c, read.h: add mult argument to s_space

	* tc-m68k.c (m68k_ip, m68k_ip_op, get_num, try_moto_index): merge
	 Motorola and MIT syntax; gas can now assemble either type of
	 file.
	tc-m68kmote.c, tc-m68kmote.h: removed now superfluous files.
	From Steve Chamberlain:
	m68kcoff.mt: for m68k COFF.
	obj-coffbfd.c: (fixup_mdeps) added
	 (size_section) removed bad sanity check
	 (fill_section) added rs_machine_dependent case
	 (write_object_file) call fixup_mdeps
	 (fixup_segment) set fx_subsy to 0.
	obj-coffbfd.h: define WORKING_DOT_WORD (too hard to support) and
	 handle m68k.
	tc-m68k.c, config/tc-m68k.h: added m68k COFF support and Motorala
	 pseudo ops.

Tue Sep  8 17:10:58 1992  Ken Raeburn  ([email protected])

	* Makefile.in (LIBS): Include opcode library.

Fri Sep  4 18:20:56 1992  Ken Raeburn  ([email protected])

	* config/tc-m68k.c (get_num, case SEG_BIG): If only small integers
	including zero are accepted, pass +0.0.

Sun Aug 30 21:24:46 1992  Ian Lance Taylor  ([email protected])

	* Makefile.in: map "as" through program_transform_name when
	installing.

	* doc/Makefile.in: map "as" through program_transform_name when
	installing.

Sat Aug 29 12:11:12 1992  Jim Wilson  ([email protected])

	* Makefile.in (as.new): Depend on LOCAL_LOADLIBES.

Fri Aug 28 16:25:22 1992  Ian Lance Taylor  ([email protected])

	* obj-bout.h, obj-bout.c (obj_header_append, obj_symbol_to_chars),
	tc-i960.c (md_ri_to_chars): Always output bout object file in
	little endian byte order (used to use endianness of host).

Tue Aug 25 15:50:48 1992  Ken Raeburn  ([email protected])

	* config/tc-m68k.c (init_table): Now const.  Always include 68851
	data, so that "bc" is available to 68040 cache instructions.
	Added "tt0", "tt1", and 68ec030 variants.
	(md_assemble): Complain if 68000 (only) and 68881 are specified.
	(enum _register): Added TT0, TT1.
	(m68k_ip, cases '3' and 't'): Handle new operand type codes.  Pass
	line number correctly in "internal error" messages.  Don't print
	architecture-mismatch message for operand errors.

	From Colin Smith ([email protected]):
	* config/tc-m68k.c (m68k_ip, case '_'): Use addword twice rather
	than install_operand.

Tue Aug 25 15:13:48 1992  Steve Chamberlain  ([email protected])

	* listing.c (buffer_line): rewind to the start of include
	files, they might be included twice.

	* z8k.c, z8k.h, z8k.mt: z8000 support stuff

Mon Aug 24 12:45:43 1992  Ian Lance Taylor  ([email protected])

	* Makefile.in: defined TARGET_CPU for C code so that it can choose
	one element of a family.

	* tc-m68k.c: use TARGET_CPU to choose default cpu type.

	* te-generic.h: default to LOCAL_LABELS_DOLLAR and LOCAL_LABELS_FB
	so that we can assemble hand-written libgcc code.

Fri Aug 21 14:38:44 1992  Ken Raeburn  ([email protected])

	* messages.c (as_warn): Use fputs, not fprintf, with a buffer that
	has already been formatted (but may still contain %-characters).
	(as_bad): Likewise.

Wed Aug 19 11:20:59 1992  Ian Lance Taylor  ([email protected])

	* tc-m68k.c, tc-m68kmote.c: the cas2 instruction is supposed to be
	written with indirection on the last two operands, which can be
	either data or address registers.  Added a new operand type 'r'
	which accepts either register type.  Added '(' to notend stuff in
	tc-m68kmote.c to accept (a0):(a2) in cas2 instruction.

Wed Aug 19 09:25:09 1992  Ken Raeburn  ([email protected])

	* as.h (enum _relax_state): Start off at one, not zero, to better
	catch uninitialized-variable errors.
	(linkrelax): Declare new variable.

	* messages.c (warning_count, error_count): Default initializer is
	sufficient.

	* write.c: Merged some declarations, using PARMS macro.
	(text_frag_root, data_frag_root, bss_frag_root, text_last_frag,
	data_last_frag): No longer static.
	(write_object_file, case rs_align or rs_org): If HANDLE_ALIGN is
	defined, call it.  Change segments before calling fixup_segment.
	(relax_align): If linkrelax, provide extra padding.

	* obj-bout.c (obj_emit_relocations): Emit alignment relocs despite
	their not having symbols associated.

	* tc-i960.c (norelax, instrument_branches): Default initializer is
	sufficient.
	(linkrelax): Delete variable definition.
	(mem_fmt): Call fix_new with NO_RELOC.
	(tc_bout_fix_to_chars): Handle alignment relocs.
	(i960_handle_align): New function.
	* tc-i960.h (linkrelax): Delete declaration.
	(HANDLE_ALIGN): New macro; calls i960_handle_align.
	(NEED_FX_R_TYPE, NO_RELOC): New macros.

Tue Aug 18 14:59:21 1992  Ken Raeburn  ([email protected])

	* config/sparc.mt: New file.  Grab sparc opcode table from bfd
	library.

Tue Aug 18 14:16:38 1992  Ian Lance Taylor  ([email protected])

	* Makefile.in: always create installation directories.  Removed
	MINUS_G, set CFLAGS to default to -g, added FLAGS_TO_PASS, passed
	FLAGS_TO_PASS to recursive makes.

	* doc/Makefile.in: always create installation directories.

Mon Aug 17 15:09:56 1992  Steve Chamberlain  ([email protected])

	* input-scrub.c (input_scrub_pop, input_scrub_push): memcpy was
	being used with args swapped, causing occasional lossage when
	refilling buffers after an include file.

Mon Aug 17 13:18:51 1992  Ken Raeburn  ([email protected])

	* messages.c (as_tsktsk): Use correct ANSI form for stdarg
	version.  Discard bogus DONTDEF version.
	(as_warn, as_bad, as_fatal): Likewise.

Fri Aug 14 18:31:14 1992  Ken Raeburn  ([email protected])

	* config/tc-m68k.c (m68k_ip): If instruction is invalid for the
	selected architecture, print a message saying so and listing what
	processors support it, rather than saying "operands mismatch".

Thu Aug 13 13:53:19 1992  Ken Raeburn  ([email protected])

	* as.h [BROKEN_ASSERT]: If defined, turn off all assertion checks.

	* config/ho-rs6000.h (M_RS6000): Don't define it.
	(free): Declare it.
	(BROKEN_ASSERT): Define it if not __STDC__.

Tue Aug 11 12:58:14 1992  Ken Raeburn  ([email protected])

	* sparc.mt: New file.

Mon Aug 10 14:37:08 1992  Per Bothner  ([email protected])

	* tc-m68k.c: ".align N" means align to N-byte boundary *only*
	if TN_SUN3; otherwise align to 2**N-byte bounary.

Thu Aug  6 12:10:39 1992  Steve Chamberlain  ([email protected])

	* read.c (s_fill): make the .fill size clamped error a warn and
	fix bug where 0's were always placed.

	* config/tc-h8300.c: if a :8 is seen after an operand, fill top
	two bytes of any constant with 0xff:

Wed Aug  5 12:02:40 1992  Steve Chamberlain  ([email protected])

	* config/tc-m68k.c (md_pseudo_table): fix the .align thing
	the right way; for just the 68k. Sun 3 .align is nbytes, not ptwo.

Wed Aug  5 01:54:34 1992  John Gilmore  (gnu at cygnus.com)

	* tc-m68k.c (try_index):  Error if index scaling specified and
	assembling for an older CPU than a 68020.

Sat Aug  1 19:10:13 1992  Ken Raeburn  ([email protected])

	* config/tc-sparc.c (tc_aout_fix_to_chars): If pc-relative, take
	fx_offset into account.

Fri Jul 31 21:53:28 1992  Ken Raeburn  ([email protected])

	* configure.in (mips host): Accept "ultrix" with version number.

	* expr.c (floating_constant): Separate "=-" to avoid confusing
	ancient or broken compilers.

	* config/tc-m68k.c (m68k_ip): Mismatch error could also indicate
	processor/opcode mismatch, so reword the error message.
	(md_assemble): If no CPU has been set (even if FPU/PMMU
	characteristics have been), default to 68020.  Don't need extra
	quotes around error string.

Fri Jul 31 12:26:34 1992  Jim Wilson  ([email protected])

	* read.c (potable): Revert sac's incorrect change made Jul 13.
	Align really is supposed to be ptwo not nbytes.

Mon Jul 20 02:51:59 1992  D. V. Henkel-Wallace  ([email protected])

	* Makefile.in: _Do_ include libiberty.  (from sef)

Fri Jul 17 15:15:28 1992  Ken Raeburn  ([email protected])

	* expr.c (integer_constant): Handle "0f" and "0b" label references
	properly.

Thu Jul 16 08:20:17 1992  Steve Chamberlain  ([email protected])

	* write.c (fixup_segment): if relaxing, don't do anything.
	* config/obj-bout.[ch] : maintain the a_relaxable file header info
	* config/tc-i960.c: new option -linkrelax

Mon Jul 13 14:11:36 1992  Steve Chamberlain  ([email protected])

	* expr.c (expr): allow SEG_BSS in expressions
	* read.c (potable): align should be nbytes, not ptwo!
	* write.c (write_object_file): extra glue for new bss attributes
	(relax_segment): SEG_BSS is ok now
	* config/tc-m68k.c (m68k_ip_op): can now parse more @( modes

Mon Jul  6 17:09:32 1992  Steve Chamberlain  ([email protected])

	* obj-coffbfd.c (fill_section): mark .lit sections as STYP_LIT

Mon Jun  1 16:20:22 1992  Michael Tiemann  ([email protected])

	* configure.in: recognize m680x0 as having sun3 emulation mode for
	vxworks environment.


Tue Jun 30 20:25:54 1992  D. V. Henkel-Wallace  ([email protected])

	* Makefile.in: Add program_suffix (parallel to program_prefix)

Wed Jun 24 10:57:54 1992  Steve Chamberlain  ([email protected])

	* app.c (process_escape): new function to handle escapes the right
	way, (do_scrub_next_char): use new function
	* cond.c (s_ifdef): do ifdef/ifndef right
	* read.c (s_fill): make the , expressions optional like the doc
	says
	* config/tc-h8300.[ch]: better warnings

Tue Jun  9 07:54:54 1992  Steve Chamberlain  ([email protected])

	* subsegs.c (subsegs_begin): create bss0_frchainP in the same was
	as data0_frchainP

	* write.c (write_object_file): various changes to handle data in
	the BSS segment in much the same was as stuff in the DATA segment.

	* tc-m68k.c (m68kip): Fix typo so that only arch's >=68020 do
	pcrel data stuff. (md_estimate_size_before_relax): when relaxing a
	68010 bxx into a bra+6 jmpxx, put the bytes of the jmp opcode into
	the right place. (s_bss): Don't put .bss stuff into SEG_DATA, put
	it into SEG_BSS

Thu Jun  4 11:59:13 1992  Steve Chamberlain  ([email protected])

	* expr.c(expr): allow SEG_REGISTER in expressions.
	* read.c(pseudo_set): register expressions can be the source of a
	set.
	* subsegs.c (subseg_new): Now -R forces all changes to SEG_DATA to
	goto SEG_TEXT (if a.out)
	* write.c (write_object_file): If a.out don't use the old way for
	-R.
	* config/obj-a.out (s_sect): complain if the user tries to use a
	subsegment with a value which might interfere with out -R hackery.
	* config/tc-m68k.c (m68k_reg_parse): lookup names in symbol table
	rather than use ugly if tree. (init_regtable): insert register
	names into symbol table.

Tue Jun  2 16:47:09 1992  Steve Chamberlain ([email protected])

	* write.c (write_object_file): keep the fix_tail clean, which
	fixes a bug in -R where relocations were being lost.

Mon Jun  1 16:20:22 1992  Michael Tiemann  ([email protected])

	* configure.in: recognize m680x0 as having sun3 emulation mode for
	vxworks environment.

Sun May 31 05:33:00 1992  david d `zoo' zuhn ([email protected])

 	* configure.in: recognize m680x0 as an m68k

Thu May 28 11:22:02 1992  Jim Wilson  ([email protected])

	* configure.in: Recognize sparclite as a sparc variant.

	* tc-sparc.c: Use new ARCHITECTURES_CONFLICT_P macro.  Mention new
	-Asparclite flag.

Tue May 26 16:47:56 1992  Steve Chamberlain  ([email protected])

	* config/tc-a29k.c: lint
	* listing.c, expr.c: patches from Andrew Smith

Thu May 14 17:22:48 1992  K. Richard Pixley  ([email protected])

	* doc/Makefile.in: use m4 rather than gm4.

Mon May  4 18:56:19 1992  Steve Chamberlain  ([email protected])

	* obj-coffbfd.c: use is a synonym for section, (do_relocs_for):
	calc the base of relocs correctly.
	* tc-a29k.c (parse_operand): allow expressions to be in any section.

Mon Apr 27 13:13:31 1992  K. Richard Pixley  ([email protected])

	* as.c, write.c: use -K rather than -k for the broken word warning
	  option.

Tue Apr 21 13:35:30 1992  K. Richard Pixley  ([email protected])

	* Makefile.in: do not print recursion lines.

Wed Apr 15 21:19:31 1992  K. Richard Pixley  ([email protected])

	* Makefile.in: the tooldir copy of gas goes directly in tooldir.

Tue Apr 14 14:50:22 1992  Ken Raeburn  ([email protected])

	* write.c (write_object_file): For b.out format, round up section
	start addresses to match required alignment.

Thu Apr  9 05:45:29 1992  Ken Raeburn  ([email protected])

	* Makefile.in (install): Install into $(tooldir)/bin, since that's
	where gcc looks for it.

Tue Apr  7 15:12:15 1992  Sean Eric Fagan  ([email protected])

	* Makefile.in:  Changed some lines to be less confusing for some
	makes.

	* input-file.c:  Conditionalize on _IOFBF, not VMS.

	* read.c, write.c:  Change a series of ifdef/elif to
	ifdef/else/ifdef etc.

Fri Mar 27 12:21:16 1992  K. Richard Pixley  ([email protected])

	* symbols.c (fb_label_init): fix sizeof to memset.

Fri Mar 13 15:45:44 1992  K. Richard Pixley  ([email protected])

	* Makefile.in: install the man page.

	* Makefile.in: pass down MAKEINFO explicitly on info.

	* doc/Makefile.in: use $(MAKEINFO) not makeinfo.

Fri Mar 13 08:03:03 1992  Steve Chamberlain  ([email protected])

	* flonum-const.c: renamed flonum-konst.c to stop dos name
	conflict.

Thu Mar 12 04:42:38 1992  K. Richard Pixley  ([email protected])

	* tc-m68k.h, te-sun3.h: moved LOCAL_LABELS_FB definition from
	  tc-m68k.h to te-sun3.h.

Wed Mar 11 23:32:42 1992  K. Richard Pixley  ([email protected])

	* configure.in: vxworks68 gets te-sun3.h.

	* expr.c: remove limitation that local_labels_dollar or
	  local_labels_fb must be < 10.

	* symbols.c: remove local_labels_dollar, replace with a function
	  interface for a sparse array.  All users adjusted.

	* te-sun3.h: add LOCAL_LABELS_DOLLAR.

Sat Mar  7 00:06:25 1992  K. Richard Pixley  ([email protected])

	* doc/Makefile.in: commented out line for building as-all.texinfo.
	  This is temporary.

	* doc/as.texinfo, doc/as-all.texinfo: added menu item hooks.

Fri Mar  6 21:57:18 1992  K. Richard Pixley  ([email protected])

	* Makefile.in: added check target.

Tue Mar  3 15:45:56 1992  K. Richard Pixley  ([email protected])

	* Makefile.in: added tooldir and program_prefix.

Sun Mar  1 04:43:19 1992  Michael Tiemann  ([email protected])

	* write.{c,h} (fix_new): Make these declarations consistent.

Sat Feb 29 13:59:10 1992  Michael Tiemann  ([email protected])

	* Makefile.in (strerror.o): Add rule so that broken Sun make can
	work in subdirs.

Wed Feb 26 19:26:28 1992  Steve Chamberlain  (sac at thepub.cygnus.com)

	* read.c, obj-coffbfd.c : fix h8300 specific bit rot

	* expr.c (operand): if can't work out what sort of operand it is,
	then look through FLT_CHARS for a hint.

Wed Feb 26 18:04:40 1992  K. Richard Pixley  ([email protected])

	* Makefile.in, configure.in: removed traces of namesubdir,
	  -subdirs, $(subdir), $(unsubdir), some rcs triggers.  Forced
	  copyrights to '92, changed some from Cygnus to FSF.

	* doc/Makefile.in, doc/configure.in: removed traces of namesubdir,
	  -subdirs, $(subdir), $(unsubdir), some rcs triggers.  Forced
	  copyrights to '92, changed some from Cygnus to FSF.

Tue Feb 25 14:17:15 1992  Steve Chamberlain  (sac at rtl.cygnus.com)

	* expr.c: If an expression is single comma, then return with
	SEG_ABSENT rather than an error - since the sparc front end does
	really strange things with things like fbge,a

	* as.h: include bfd.h if using many sections
	* expr.c: LOCAL_LABELS_FB had been changed to lower case - so
	local labels didn't work.
	* listing.c (list_symbol_table): don't core dump when there's no
	symbol there.
	* write.c, write.h: call fix_new with the right number of args on
	the H8.
	* config/tc-h8300.[ch] : fix bugs reported by HMSI, and make
	errors nices

Sat Feb 22 12:26:28 1992  Steve Chamberlain  (sac at rtl.cygnus.com)

	* app.c: MRI compatibility - allow single quote to start a string.
	* as.c: fix typo recently introduced.
	* as.h : Don't include aout/reloc.h - it's not right for COFF!
	* expr.c: Much rewriting, to accomodate MRI syntax for
	expressions. Also easier to read now.
	* listing.c: Put back defuns
	* read.c: modified to accept MRI syntax, put back listing pseudo
	ops so that an assembler built with NO_LISTING ignores list ops
	rather than pukes.
	* write.c, write.h: fixs - only keep a reloc type in a fix if the target
	machine is a SPARC or a 29K.
	* config/obj-aout.c: added s_sect pseudo op
	* config/obj-coffbfd.c: lints, set the filehdr flags right and
	fill in the timestamp.
	* config/obj-coffbfd.h: Since we don't include aout/reloc.h
	anymore, define all the relocs which the tc-<x> bit will use so we
	can translate from them to the coff types.
	* config/tc-a29k.c: reloc_type isn't ane enum any more
	* config/tc-m68k.c: Added NO_RELOC definition.

Fri Feb 21 06:21:07 1992  K. Richard Pixley  ([email protected])

	* Makefile.in: put header files before C source for TAGS; remove
	  references to non-existent syscalls.h.

	* read.c, write.c subsegs.c: back out the .bss changes.

	* obj-aout.c: do not include stab.gnu.h if NO_LISTING.

	* tc-i860.c, a.out.gnu.h: move i860 relocs to a proper place.

	* a.out.h: removed.

Fri Feb 21 01:08:48 1992  Minh Tran-Le ([email protected])

	* symbols.c (local_label_name): symbols now start with ^A.

	* read.c, subsegs.c, write.c obj-coff.c: added handling of
	  `.bss` pseudo op for unitialized data. The new gcc (1.37.9x)
	  generate these sections.  .align: will use NOP_OPCODE or 0
	  for padding. This is just for being nice to the
	  disassembler.

	* expr.c (operand): changed to generate local label "\001L0"
	  starting with a ^A so that it is recognized as a local label.

	* as.c (perform_an_assembly_pass): zero bss_fix_root, too.

	* tc-i386.c: tc-i386.c: added handling of the following opcodes:
	  i/o opcodes - inb, inw, outb and outw.  string manipulation with
	  att syntax - scmp, slod, smov, ssca, ssto.

	* obj-coff.c: (for aix386) Moved the symbols .text, .data and .bss
	  to just after .file .

	  In obj_crawl_symbol_chain() where it tries to put the external
	  symbols apart, with the condition:
	    (!S_IS_DEFINED(symbolP) &&
	     !S_IS_DEBUG(symbolP) &&
	     !SF_GET_STATICS(symbolP))
	  it was moving too many symbols out. So I switch it back to the
	  condition:
	    (S_GET_STORAGE_CLASS(symbolP) == C_EXT && !SF_GET_FUNCTION(symbolP))

	  In obj_emit_relocations() added the conditional on KEEP_RELOC_INFO
	  so that we don't use the F_RELFLG which make the linker complain
	  that somebody has stripped the relocation info.

	  Also, the AIX ld program require that the relocation table
	  is sorted by r_vaddr like the standard ATT assembler does.

	  [he also changed the sizeof(struct ...)'s into the coff
	  style FOOSZ macros.  I'm not sure this is right, but I can't
	  remember why.  xoxorich.]

Fri Feb 21 01:08:48 1992  K. Richard Pixley  ([email protected])

	* Makefile.in, configure.in, doc: use the doc.  Build it, install
	  it, clean it, etc.

Tue Feb 18 02:21:25 1992  K. Richard Pixley  (rich at cygnus.com)

	* read.c: white space and comments only.

	* configure.in: use the new atof-ns32.c for ns32k.

	* write.c: comment change only.

	* tc-m88k.[hc]: pulled in from hack's unfinished work.  These
	  aren't yet integrated.

	* tc-i860.[hc]: blew off the dust.  Something must still be done
	  about conflicting relocation types.

	* tc-ns32k.c: Replaced previous tc_aout_fix_to_chars stub with the
	  real thing.

	* tc-i960.c, tc-sparc.c: white space and comments only.

	* tc-a29k.h: delete duplicate macro definition.

	* new file atof-ns32k.c copied from hack's last unreleased gas.

Mon Feb 17 07:51:06 1992  K. Richard Pixley  (rich at cygnus.com)

	* config/tc-ns32k.c: actually make tc_aout_fix_to_chars work
	  rather than abort.

	* nearly everything.  flush ChangeLog, package as gas-1.92.1.
	  ChangeLog's prior to this are sketchy at best.  I have logs.
	  They just aren't ChangeLogs.