* printcmd.c (print_formatted): Don't use tab in wrap_here arg.

[binutils.git] / gdb / serial.h

/* Remote serial support interface definitions for GDB, the GNU Debugger.
   Copyright 1992, 1993 Free Software Foundation, Inc.

This file is part of GDB.

This program is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 2 of the License, or
(at your option) any later version.

This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
GNU General Public License for more details.

You should have received a copy of the GNU General Public License
along with this program; if not, write to the Free Software
Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.  */

/* Terminal state pointer.  This is specific to each type of interface. */

typedef PTR serial_ttystate;

struct _serial_t
{
  int fd;			/* File descriptor */
  struct serial_ops *ops;	/* Function vector */
  serial_ttystate ttystate;	/* Not used (yet) */
  int bufcnt;			/* Amount of data in receive buffer */
  unsigned char *bufp;		/* Current byte */
  unsigned char buf[BUFSIZ];	/* Da buffer itself */
  int current_timeout;		/* (termio{s} only), last value of VTIME */
};

typedef struct _serial_t *serial_t;

struct serial_ops {
  char *name;
  struct serial_ops *next;
  int (*open) PARAMS ((serial_t, const char *name));
  void (*close) PARAMS ((serial_t));
  int (*readchar) PARAMS ((serial_t, int timeout));
  int (*write) PARAMS ((serial_t, const char *str, int len));
  void (*go_raw) PARAMS ((serial_t));
  serial_ttystate (*get_tty_state) PARAMS ((serial_t));
  int (*set_tty_state) PARAMS ((serial_t, serial_ttystate));
  int (*setbaudrate) PARAMS ((serial_t, int rate));
};

/* Add a new serial interface to the interface list */

void serial_add_interface PARAMS ((struct serial_ops *optable));

serial_t serial_open PARAMS ((const char *name));

serial_t serial_fdopen PARAMS ((int fd));

/* For most routines, if a failure is indicated, then errno should be
   examined.  */

/* Try to open NAME.  Returns a new serial_t on success, NULL on failure.
 */

#define SERIAL_OPEN(NAME) serial_open(NAME)

/* Open a new serial stream using a file handle.  */

#define SERIAL_FDOPEN(FD) serial_fdopen(FD)

/* Turn the port into raw mode. */

#define SERIAL_RAW(SERIAL_T) (SERIAL_T)->ops->go_raw((SERIAL_T))

#define SERIAL_GET_TTY_STATE(SERIAL_T) (SERIAL_T)->ops->get_tty_state((SERIAL_T))

#define SERIAL_SET_TTY_STATE(SERIAL_T, TTYSTATE) (SERIAL_T)->ops->set_tty_state((SERIAL_T), (TTYSTATE))

/* Read one char from the serial device with TIMEOUT seconds timeout.
   Returns char if ok, else one of the following codes.  Note that all
   error codes are guaranteed to be < 0.  */

#define SERIAL_ERROR -1		/* General error, see errno for details */
#define SERIAL_TIMEOUT -2
#define SERIAL_EOF -3

#define SERIAL_READCHAR(SERIAL_T, TIMEOUT) ((SERIAL_T)->ops->readchar((SERIAL_T), TIMEOUT))

/* Set the baudrate to the decimal value supplied.  Returns 0 for success,
   -1 for failure.  */

#define SERIAL_SETBAUDRATE(SERIAL_T, RATE) ((SERIAL_T)->ops->setbaudrate((SERIAL_T), RATE))

/* Write LEN chars from STRING to the port SERIAL_T.  Returns 0 for success,
   -1 for failure.  */

#define SERIAL_WRITE(SERIAL_T, STRING, LEN) ((SERIAL_T)->ops->write((SERIAL_T), STRING, LEN))

/* Push out all buffers, close the device and destroy SERIAL_T. */

void serial_close PARAMS ((serial_t));

#define SERIAL_CLOSE(SERIAL_T) serial_close(SERIAL_T)