Jens Kuske [Thu, 10 Dec 2015 10:41:02 +0000 (11:41 +0100)]
sunxi: Fix H3 DRAM DQ read delay configuration
The read delays were set incorrectly, leading to reliability
issues at higher DRAM clock speeds. This commit adjusts this
to match the vendor boot0 behaviour.
Commit 6c739c5d added code to enable i2c bus 4 and 5 on the sun7i SoC
but forgot to extend the range check in clock_twi_onoff, resulting in
the clock not getting enabled.
The range-check is not needed at all, since clock_twi_onoff only gets
called with such high indexes when CONFIG_I2C3_ENABLE / CONFIG_I2C4_ENABLE
is set and Kconfig already only allows these on sun6i / sun7i.
This commit removes the range-check all together fixing i2c bus 4 and 5
not working on sun7i.
vishnupatekar [Sat, 28 Nov 2015 17:07:25 +0000 (01:07 +0800)]
sunxi: Add support for Allwinner A83T DRAM
Add support for A83T dram. Register are different from sun8i A33.
init code is similar to A33 dram init.
hope we'll shift duplicate code in dram_sun8i_*
to dram helper in future.
vishnupatekar [Sat, 28 Nov 2015 17:07:24 +0000 (01:07 +0800)]
sunxi: clk: add basic clocks for A83T
Add basic clocks pll1, pll5, and some default values from allwinner u-boot.
Signed-off-by: Vishnu Patekar <[email protected]>
[[email protected]] Fix PLL6 init to run at 600 MHz instead of 288 MHz,
fixing the mmc support not working
[[email protected]] Fix PLL init code to properly wait for the PLL-s to
stabilize, fixing cold-booting directly from sdcard not working Signed-off-by: Hans de Goede <[email protected]>
vishnupatekar [Sat, 28 Nov 2015 17:07:21 +0000 (01:07 +0800)]
sunxi: power: axp818: add support for axp818 driver
AXP818 is rsb based PMIC and used on Allwinner A83T H8 Homlet dev board.
It's registers are different and calculating reg config is different than
that of earlier axp power ICs.
DCDC1, DCDC2, DCDC3 and DCDC5 is implemented at the moment.
all other voltages can be added subsequently.
AXP datasheet is uploaded to wiki:
http://linux-sunxi.org/File:AXP818_datasheet_Revision1.0.pdf
Hans de Goede [Fri, 20 Nov 2015 18:29:49 +0000 (19:29 +0100)]
sunxi: Set AHB1 clock to PLL6/3 on all clock_sun6i.h using SoCs
According to the datasheets the max speed of AHB1 is 276 MHz, so
setting it to PLL6 / 3 which gives us 200MHz everywhere is fine,
and gives us a nice speed-up in certain workloads.
Bin Meng [Thu, 26 Nov 2015 01:46:08 +0000 (17:46 -0800)]
x86: Remove CPU_INTEL_SOCKET_RPGA989
This Kconfig option name indicates it has something to do with cpu
socket, however it is actually not the case. Remove it and move
options inside it to NORTHBRIDGE_INTEL_IVYBRIDGE.
Bin Meng [Wed, 9 Dec 2015 01:31:39 +0000 (17:31 -0800)]
x86: Move i8254_init() to x86_cpu_init_f()
Right now i8254_init() is called from timer_init() in the tsc timer
driver. But actually i8254 and tsc are completely different things.
Since tsc timer has been converted to driver model, we should find
a new place that is appropriate for U-Boot to call i8254_init(),
which is now x86_cpu_init_f().
Bin Meng [Mon, 7 Dec 2015 13:28:13 +0000 (05:28 -0800)]
x86: Fix PCI UART compatible string for crownbay and galileo
With recent ns16550 driver changes, we only changed the legacy UART
(at I/O port 0x3f8) compatible string, but forgot to change the PCI
UART compatible string. Now fix it.
Bin Meng [Mon, 7 Dec 2015 09:39:47 +0000 (01:39 -0800)]
fdt: Change OF_BAD_ADDR to FDT_ADDR_T_NONE
Currently OF_BAD_ADDR is always -1ULL. When using OF_BAD_ADDR as the
return value of dev_get_addr(), it creates potential size mismatch
as dev_get_addr() uses FDT_ADDR_T_NONE as the return value which can
be either -1U or -1ULL depending on CONFIG_PHYS_64BIT. Now we change
OF_BAD_ADDR to FDT_ADDR_T_NONE to avoid such case.
Marek Vasut [Mon, 7 Dec 2015 17:01:54 +0000 (18:01 +0100)]
mkimage: Fix warning from fix for generating multi and script images again
Seems 6ae6e160 broke creating images in certain cases, there
are two problems with that patch.
First is that the expression "!x == 4 || !x == 6" is ambiguous. The
intention here was "!(x == 4) || !(x == 6)" based on reading further in
the file, where this was borrowed from. This however is interpreted by
gcc as "(!x) == 4 || (!x) == 6" and always false. gcc-5.x will warn
about this case.
The second problem is that we do not want to test for the case of "(NOT x
is 4) OR (NOT x is 6)" but instead "(x is not equal to 4) AND (x is not
equal to 6)". This is because in those two cases we already execute the
code question in another part of the file. Rewrite the expression and
add parenthesis for clarity.
Tom Rini [Mon, 7 Dec 2015 13:23:29 +0000 (08:23 -0500)]
CONFIG_NEEDS_MANUAL_RELOC: Fix warnings when not set
Now that we may compile (but not link) code calling fixup_cmdtable when
this is not set, we need to always have the declaration available. We
should also make sure that anyone calling the function includes
<command.h> as that's where the function declaration is.
Michal Simek [Tue, 1 Dec 2015 07:37:16 +0000 (08:37 +0100)]
dm: core: Enable SPL_SIMPLE_BUS by default
This option is needed for all SoCs which have nodes on bus. Without
enabling this drivers are not found and probed.
Issue was found on Zynq MMC probe.
Enable this option by default.
zynq: sdhci: Calculate minimum frequency based on max frequency
Calculate the minimum sd clock based on max clock. This will
be done by add_sdhci() if we pass minimum clock as zero.
It also does based on SD host contoller version.
Michal Simek [Mon, 23 Nov 2015 15:27:38 +0000 (16:27 +0100)]
ARM: zynq: Fix location of stack and malloc areas
The patch
"board_init: Change the logic to setup malloc_base"
(sha1: 9ac4fc82071ce346e3885118242ff45d22f69b82)
breaks SPL for Zynq because it puts early alloc area on the stack which
caused that stack was decreased by CONFIG_SYS_MALLOC_F_LEN (0x400)
and there was not enough space for regular stack.
This patch changes memory layout to better utilize the last 64k OCM
block.
0xffff0000 - 0xfff1000 - Full malloc space
0xffff1000 - 0xffff300 - Stack location
0xfffff300 - CONFIG_SYS_MALLOC_F_LEN - Early malloc space
0xfffffd00 - sizeof(GD) - GD
0xfffffe00 - 0xffffffff - SoC specific boot code
Michal Simek [Mon, 30 Nov 2015 13:14:56 +0000 (14:14 +0100)]
net: gem: Move driver to DM
- Enable DM_ETH by default for Zynq and ZynqMP
- Remove board_eth_init code
- Change miiphy_read function to return value instead of error code
based on DM requirement
- Do not enable EMIO DT support by default
Michal Simek [Mon, 30 Nov 2015 09:24:15 +0000 (10:24 +0100)]
net: gem: Change mii function not to use eth_device structure
Next step to move driver to driver model. Do not use eth_device
structure. Use private structure instead.
Add iobase to private structure to store gem iobase.
Rajesh Bhagat [Wed, 2 Dec 2015 06:14:27 +0000 (11:44 +0530)]
usb: xhci: dwc3: Adding reset delay requirement as per dwc3 databook
As per dwc3 databook, delay is required before taking the core out of reset.
This delay is required so that the PHY are stable, and then we can take core
out of reset.
Reference is taken from linux dwc3 code, file: drivers/usb/dwc3/core.c.
Alexey Brodkin [Wed, 2 Dec 2015 09:32:02 +0000 (12:32 +0300)]
usb: add support for generic EHCI devices
This driver is meant to be used with any EHCI-compatible host
controller in case if there's no need for platform-specific
glue such as setup of controller or PHY's power mode via
GPIOs etc.
Felipe Balbi [Thu, 1 Oct 2015 19:22:18 +0000 (14:22 -0500)]
usb: dwc3: fix build warnings
fix the following build warnings:
drivers/usb/dwc3/core.c: In function ‘dwc3_uboot_init’:
drivers/usb/dwc3/core.c:625:6: warning: ‘dev’ is used uninitialized in this function [-Wuninitialized]
mem = devm_kzalloc(dev, sizeof(*dwc) + DWC3_ALIGN_MASK, GFP_KERNEL);
^
drivers/usb/dwc3/dwc3-omap.c: In function ‘dwc3_omap_uboot_init’:
drivers/usb/dwc3/dwc3-omap.c:380:7: warning: ‘dev’ is used uninitialized in this function [-Wuninitialized]
omap = devm_kzalloc(dev, sizeof(*omap), GFP_KERNEL);
Felipe Balbi [Thu, 1 Oct 2015 19:22:17 +0000 (14:22 -0500)]
usb: host: xhci-omap: fix build break
Fix the following build break:
drivers/usb/host/xhci-omap.c:35:5: error: ‘board_usb_init’ aliased to external symbol ‘__board_usb_init’
int board_usb_init(int index, enum usb_init_type init)
^
Thomas Chou [Tue, 1 Dec 2015 08:18:20 +0000 (16:18 +0800)]
altera_qspi: fix erase and write error code
Fix erase and write error code, which should be "protected".
From the "Embedded Peripherals IP User Guide" of Altera,
The "Illegal write" flag indicates that a write instruction is
targeting a protected sector on the flash memory. This bit is
set to indicate that the IP has cancelled a write instruction.
The "Illegal erase" flag indicates that an erase instruction has
been set to a protected sector on the flash memory. This bit is
set to indicate that the IP has cancelled the erase instruction.
Simon Glass [Fri, 4 Dec 2015 15:58:39 +0000 (08:58 -0700)]
dm: tegra: Provide serial platform data for SPL
At present an incorrect #if term is preventing this data from being compiled
in. All tegra boards use driver model for serial, so we can just drop this.
Fixes: fde7e18938d8 ("dm: tegra: pci: Move CONFIG_PCI_TEGRA to Kconfig") Signed-off-by: Simon Glass <[email protected]> Reported-by: Stephen Warren <[email protected]> Acked-by: Thomas Chou <[email protected]>
Simon Glass [Fri, 4 Dec 2015 15:58:38 +0000 (08:58 -0700)]
dm: serial: ns16550: Add pre-reloc flag to the driver
For platforms that don't use device tree in SPL the only way to mark this
driver as 'required by relocation' is with the DM_FLAG_PRE_RELOC flag. Add
this to ensure that the driver is bound.
Fixes: fde7e18938d8 ("dm: tegra: pci: Move CONFIG_PCI_TEGRA to Kconfig") Signed-off-by: Simon Glass <[email protected]> Reported-by: Stephen Warren <[email protected]> Acked-by: Thomas Chou <[email protected]>
Stephen Warren [Sat, 5 Dec 2015 05:07:45 +0000 (22:07 -0700)]
rpi: fix revision scheme parsing
The RPi has two different schemes for encoding board revision values.
When adding RPi 2 support, I thought that the conflicting type field
values were to be interpreted based on bcm2835-vs-bcm2836. In fact, the
scheme bit determines the encoding. The RPi Zero uses the bcm2835 yet
uses the new encoding scheme. Fix the code to cater for this correctly.
Stephen Warren [Sat, 5 Dec 2015 05:07:44 +0000 (22:07 -0700)]
rpi: get rid of BCM2835_BOARD_REV_* macros
There are two numbering schemes for the RPi revision values; old and new
scheme. The values within each scheme overlap. Hence, it doesn't make
sense to have absolute/global names for the revision IDs. Get rid of the
names and just use the raw revision/type values to set up the array of
per-revision data.
This change makes most sense when coupled with the next change. However,
it's split out so that the mechanical cut/paste is separate from the
logic changes for easier review and problem bisection.
Seems 92a655c3 broke creating multi and script type images.
Since the file1:file2:file3 string does not get split up,
it fails on trying to open an non-existing file.
mkimage -A arm -O linux -T multi -C none -d zImage:splash.bmp:device.dtb uimage
tools/mkimage: Can't open zImage:splash.bmp:device.dtb: No such file or directory
Since the sizes of the different parts seem to get added in the actual
routine that handles multi and script type images, we can probably skip the
bit of the code that causes the failure for that type of images.
common: board: Dont relocate FDT incase of CONFIG_OF_EMBED
Don't relocate fdt in case of CONFIG_OF EMBED as the fdt is
already embedded with u-boot image.
Update fdt_blob after relocation as the fdt will be copied
during u-boot relocation.
Simon Glass [Wed, 2 Dec 2015 17:59:13 +0000 (10:59 -0700)]
spl: mmc: Unify non/driver model spl_mmc_find_device()
It is risky to have two different functions with much the same code. Future
authors may update one but not the other. It is hard to see which parts are
the same and which are different.
Unify the functions and drop the differences that are not really needed.
Note that one puts() becomes printf() as Tom mentioned that this does not
affect image size:
https://patchwork.ozlabs.org/patch/537276/
Note: It would be better to have an empty printf() and avoid the #ifdef for
CONFIG_SPL_LIBCOMMON_SUPPORT.
Simon Glass [Wed, 2 Dec 2015 17:59:11 +0000 (10:59 -0700)]
spl: mmc: Fix compiler warning with CONFIG_DM_MMC
Since commit 4188ba3 we get the following warning on rockchip boards:
common/spl/spl_mmc.c:31:24: warning: ‘mmc’ may be used uninitialized in this function [-Wmaybe-uninitialized]
count = mmc->block_dev.block_read(0, sector, 1, header);
^
common/spl/spl_mmc.c:251:14: note: ‘mmc’ was declared here
struct mmc *mmc;
Nishanth Menon [Tue, 1 Dec 2015 04:05:58 +0000 (22:05 -0600)]
drivers: remoteproc: rproc-uclass: Fix check for NULL pointers
Neither uc_pdata->name nor check_name are supposed to be NULL in
_rproc_name_is_unique(). if uc_pdata->name is NULL, we are not
intialized yet, however if check_data is NULL, we do not have
proper data. Further, if either were NULL, strlen will crap out
while attempting to derefence NULL.
Instead, just check if either of these are NULL and bail out.
This should also fix the following coverity scan warnings:
*** CID 132281: Null pointer dereferences (FORWARD_NULL)
/drivers/remoteproc/rproc-uclass.c: 73 in _rproc_name_is_unique()
Thomas Chou [Sun, 29 Nov 2015 06:01:03 +0000 (14:01 +0800)]
ns16550: change reg-shift property default to zero
Change reg-shift property default to zero. When the integer property
is missing, it should be taken as zero. This is consistent to Linux
drivers/tty/serial/of_serial.c.
The x86 and most powerpc use reg-shift of 0. Most others use reg-shift
of 2. While reg-shift of 1 is rarely used.
Stefan Roese [Thu, 26 Nov 2015 12:38:15 +0000 (13:38 +0100)]
common/Makefile: Compile fdt_support is enabled in SPL
When CONFIG_SPL_OF_TRANSLATE is enabled fdt_support.c needs to get
compiled. Otherwise fdt_translate_address() is missing which is needed
in dev_get_addr().
projects / J-u-boot.git / log