MIPS: add BMIPS Comtrend VR-3032u board

Signed-off-by: Álvaro Fernández Rojas <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

MIPS: add support for Broadcom MIPS BCM63268 SoC family

Signed-off-by: Álvaro Fernández Rojas <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

MIPS: add BMIPS Comtrend AR-5387un board

Signed-off-by: Álvaro Fernández Rojas <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

MIPS: add support for Broadcom MIPS BCM6328 SoC family

Signed-off-by: Álvaro Fernández Rojas <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

MIPS: add BMIPS Huawei HG556a board

Signed-off-by: Álvaro Fernández Rojas <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

MIPS: add support for Broadcom MIPS BCM6358 SoC family

Signed-off-by: Álvaro Fernández Rojas <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

MIPS: add initial infrastructure for Broadcom MIPS SoCs

CFE checks CPU Thread in a different way (using register $22):
mfc0 t1, C0_BCM_CONFIG, 3 # $22
li t2, CP0_CMT_TPID # (1 << 31)
and t1, t2
bnez t1, 2f # if we are running on thread 1, skip init
nop

Signed-off-by: Álvaro Fernández Rojas <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

ram: add RAM driver for Broadcom MIPS SoCs

Signed-off-by: Álvaro Fernández Rojas <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

cpu: add CPU driver for Broadcom MIPS SoCs

Signed-off-by: Álvaro Fernández Rojas <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

cmd: cpu: refactor to ensure devices are probed and improve code style

Use uclass_first_device and uclass_next_device in order to avoid exceptions
for drivers that aren't probed when cpu ops are requested.
Improve code style and fix indentations.
Fix incorrect line break when cpu info is not available.
Remove unneeded brackets.

Signed-off-by: Álvaro Fernández Rojas <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

serial: add serial driver for BCM6345

It is based on linux/drivers/tty/serial/bcm63xx_uart.c

Signed-off-by: Álvaro Fernández Rojas <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

MIPS: allow using generic sysreset drivers

Avoid duplicating do_reset definition if SYSRESET is enabled for MIPS

Signed-off-by: Álvaro Fernández Rojas <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

sysreset: add syscon-reboot driver

Add a new sysreset driver based on linux/drivers/power/reset/syscon-reboot.c,
which provides a generic driver for platforms that only require writing a mask
to a regmap offset.

Signed-off-by: Álvaro Fernández Rojas <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

cmd: cpu: fix NULL cpu feature prints

Commit 740d5d3 added two new features but only one feature name,
which results in NULL prints when device_id feature is selected.

Before:
HG556a # cpu detail
 -1: cpu@0 BCM6358A1
ID = 0, freq = 300 MHz: L1 cache, MMU, NULL
Device ID 0x2a010
 -1: cpu@1 BCM6358A1
ID = 1, freq = 300 MHz: L1 cache, MMU, NULL
Device ID 0x2a010
After:
HG556a # cpu detail
 -1: cpu@0 BCM6358A1
ID = 0, freq = 300 MHz: L1 cache, MMU, Device ID
Device ID 0x2a010
 -1: cpu@1 BCM6358A1
ID = 1, freq = 300 MHz: L1 cache, MMU, Device ID
Device ID 0x2a010

Signed-off-by: Álvaro Fernández Rojas <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>

MIPS: call debug_uart_init right before board_init_f

All MIPS boards that support debug uart are calling debug_uart_init right at
the beginning of board_early_init_f.
Instead of doing that, let's provide a generic call to debug_uart_init right
before the call to board_init_f if debug uart is enabled for boards without
stack in SRAM.
On the other hand, boards with stack in SRAM can call earlier (right before
low level init).

Signed-off-by: Daniel Schwierzeck <[email protected]>
Signed-off-by: Álvaro Fernández Rojas <[email protected]>

MIPS: tl-wdr4300: remove debug_uart_init call

In order to add a generic MIPS debug_uart_init call right before the call to
board_early_init_f, we need to remove all calls to debug_uart_init from every
MIPS boards.
WDR4300 doesn't provide a board_debug_uart_init and configures pinmux in
board_early_init_f instead. Since I have no idead of what's the needed uart
pinmux config, I copied the whole pinmux config to a new function that is
called from board_early_init_f if CONFIG_DEBUG_UART_BOARD_INIT is not enabled.

Signed-off-by: Álvaro Fernández Rojas <[email protected]>

MIPS: QCA AP143: remove debug_uart_init call

In order to add a generic MIPS debug_uart_init call right before the call to
board_early_init_f, we need to remove all calls to debug_uart_init from every
MIPS boards.

Signed-off-by: Álvaro Fernández Rojas <[email protected]>

MIPS: QCA AP121: remove debug_uart_init call

In order to add a generic MIPS debug_uart_init call right before the call to
board_early_init_f, we need to remove all calls to debug_uart_init from every
MIPS boards.

Signed-off-by: Álvaro Fernández Rojas <[email protected]>

u-boot.elf: add quiet_cmd_u-boot-elf and cmd_u-boot-elf

This way we can see output about u-boot.elf being built or not.

Signed-off-by: Álvaro Fernández Rojas <[email protected]>
Reviewed-by: Tom Rini <[email protected]>

MIPS: add support for generating u-boot.elf

Define PLATFORM_ELFFLAGS for MIPS in order to be able to generate u-boot.elf

Signed-off-by: Álvaro Fernández Rojas <[email protected]>

u-boot.elf: allow overriding entry symbol

LD gives the following warning when trying to process u-boot-elf.o
warning: cannot find entry symbol __start; defaulting to 0000000080010000
According to gnu-libc the entry symbol for mips is __start and not _start:
https://sourceware.org/git/?p=glibc.git;a=blob;f=sysdeps/mips/dl-machine.h;h=ed47513ccc1d23d23d32ee640053d2f351f3990b;hb=HEAD#l258

Signed-off-by: Álvaro Fernández Rojas <[email protected]>
Reviewed-by: Tom Rini <[email protected]>

u-boot.elf: remove hard-coded arm64 flags

This is needed in order to allow building it for other archs.
Move relocation comment to a better place.
Remove no longer needed dts FIXME.

Signed-off-by: Álvaro Fernández Rojas <[email protected]>
Reviewed-by: Tom Rini <[email protected]>

Merge git://git.denx.de/u-boot-dm

Merge git://www.denx.de/git/u-boot-marvell

defconfig: dra7xx_evm: enable CONFIG_BLK and disk driver model for SCSI

Enable disk driver model for dra7xx_evm as dwc_ahci supports
driver model. As a consequence we must also enable CONFIG_BLK and
CONFIG_DM_USB.

Signed-off-by: Mugunthan V N <[email protected]>
Signed-off-by: Jean-Jacques Hiblot <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Dropped CONFIG_SPL_PHY=y in sandbox_spl to fix build error:
Signed-off-by: Simon Glass <[email protected]>

drivers: block: dwc_ahci: Implement a driver for Synopsys DWC sata device

Implement a sata driver for Synopsys DWC sata device based on
U-boot driver model.

Signed-off-by: Mugunthan V N <[email protected]>
Signed-off-by: Jean-Jacques Hiblot <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

dra7: dtsi: mark ocp2scp bus compatible with "simple-bus"

This is needed to probe devices under that bus such as the SATA PHY.

Signed-off-by: Jean-Jacques Hiblot <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

drivers: phy: add PIPE3 phy driver

This phy is found on omap platforms with sata capabilities.
Except for the part related to the DM and the PHY framework, the code is
basically a copy paste from arch/arm/mach-omap2/pipe3-phy.c

Signed-off-by: Jean-Jacques Hiblot <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

dm: test: Add tests for the generic PHY uclass

Those tests check:
- the ability for a phy-user to get a phy based on its name or its index
- the ability of a phy device (provider) to manage multiple ports
- the ability to perform operations on the phy (init,deinit,on,off)
- the behavior of the uclass when optional operations are not implemented

Signed-off-by: Jean-Jacques Hiblot <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

drivers: phy: add generic PHY framework

The PHY framework provides a set of APIs to control a PHY. This API is
derived from the linux version of the generic PHY framework.
Currently the API supports init(), deinit(), power_on, power_off() and
reset(). The framework provides a way to get a reference to a phy from the
device-tree.

Signed-off-by: Jean-Jacques Hiblot <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

scsi: dm: split scsi_scan()

The DM version of scsi_scan() is becoming a bit long, it can be split:
scsi_scan() iterates over the IDs and LUNs and for each id/lun pair calls
do_scsi_scan_one() to do the work of:
 - detecting an attached drive
 - creating the associated block device if a drive is found.

Signed-off-by: Jean-Jacques Hiblot <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

board: at91sam9263ek: Enable early debug UART

Enable the early debug UART to debug problems when an ICE or other
debug mechanism is not available.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

board: at91sam9263ek: Clean up code

Because the introduction of the pinctrl and clk drivers and the
device tree files, remove unneeded hard coded related code from
the board file.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

configs: at91sam9263ek: Update for DT and DM support

Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

board: at91sam9rlek: Enable early debug UART

Enable the early debug UART to debug problems when an ICE or other
debug mechanism is not available.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

board: at91sam9rlek: Clean up code

Since the introduction of the pinctrl and clk drivers and the
device tree files, remove unneeded hard coded related code from
the board file.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

configs: at91sam9rlek: Update for DT and DM support

Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

board: at91sam9260ek/9g20ek: Enable early debug UART

Enable the early debug UART to debug problems when an ICE or other
debug mechanism is not available.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

board: at91sam9260ek: Clean up code

Since the introduction of the pinctrl and clk drivers and the
device tree files, remove unneeded hard coded related code from
the board file.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

configs: at91sam9260ek/9g20ek: Update for DT and DM

Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

board: at91sam9m10g45ek: Enable early debug UART

Enable the early debug UART to debug problems when an ICE or other
debug mechanism is not available.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

board: at91sam9m10g45ek: Clean up code

Since the introduction of the pinctrl and clk drivers and the
device tree files, remove unneeded hard coded related code from
the board file.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

configs: at91sam9m10g45ek: Update to support DM/DT

Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.

Because the limitation of internal SRAM size, the SPL with driver
model can't be supported, disable the SPL option.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

board: at91sam9n12ek: Enable early debug UART

Enable the early debug UART to debug problems when an ICE or other
debug mechanism is not available.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

board: at91sam9n12ek: Clean up code

Since the introduction of the pinctrl and clk driver and the device
tree files, remove unneeded related code from the board file.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

configs: at91sam9n12ek: Update for DT and DM support

Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.

Because the limitation of internal SRAM size, the SPL with driver
model can't be supported, disable the SPL option.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

board: at91sam9x5ek: Enable early debug UART

Enable the early debug UART to debug problems when an ICE or other
debug mechanism is not available.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

board: at91sam9x5ek: Clean up code

Since the introduction of the pinctrl and clock driver and the device
tree files, remove unneeded hard coded related code from the board
file.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

configs: at91sam9x5ek: Update to support DM/DT

Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.

Because the limitation of internal SRAM size, the SPL with driver
model can't be supported, disable the SPL option.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

ARM: dts: at91: Add dts files for at91sam9263ek

The device tree source files of at91sam9263ek boards are copied from
the Linux v4.10, do the changes as below.
 - Add the reg property for the pinctrl node.
 - Move the gpio (pioA, pioB, pioC, pioD, pioE) nodes as the pinctrl's
   slibling nodes, instead of the child nodes.
 - Add the "u-boot,dm-pre-reloc" property for the dbgu node are used
   in board_init_f stage.
 - Fix the compilation warnings.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

ARM: dts: at91: Add dts files for at91sam9rlek

The device tree source files of at91sam9rlek boards are copied from
the Linux v4.10, do the changes as below.
 - Add the reg property for the pinctrl node.
 - Move the gpio (pioA, pioB, pioC, pioD) nodes as the pinctrl's
   slibling nodes, instead of the child nodes.
 - Add the "u-boot,dm-pre-reloc" property for the dbgu node are used
   in board_init_f stage.
 - Fix the compilation warnings.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

ARM: dts: at91: Add dts files for at91sam9260ek/9g20ek

The device tree source files of at91sam9g20ek and at91sam9260ek
boards are copied from the Linux v4.10, do the changes below.
 - Fix the build error for the usb0 node.
 - Add the reg property for the pinctrl node.
 - Move the gpio (pioA, pioB, pioC ...) nodes as the pinctrl's
   slibling nodes, instead of the child nodes.
 - Add the "u-boot,dm-pre-reloc" property for the dbgu node are used
   in board_init_f stage.
 - Add the clk pinctrl of the mmc0 node.
 - Fix the compilation warnings.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

ARM: dts: at91: Add dts files for at91sam9m10g45ek

The device tree source files of at91sam9m10g45ek boards are copied
from the Linux v4.10, do the changes as below.
 - Add the reg property for the pinctrl node.
 - Move the gpio (pioA, pioB, pioC, pioD, pioE) nodes as the pinctrl's
   slibling nodes, instead of the child nodes.
 - Add the "u-boot,dm-pre-reloc" property to determine which nodes
   are used by the board_init_f stage.
 - Fix the compilation warnings.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

ARM: dts: at91: Add dts files for at91sam9n12ek

The device tree source files of at91sam9n12ek boards are copied from
the Linux v4.10, do the changes as below.
 - Add the reg property for the pinctrl node.
 - Move the gpio (pioA, pioB, pioC, pioD) nodes as the pinctrl's
   slibling nodes, instead of the child nodes.
 - Change the compatible of the spi flash to "spi-flash".
 - Add the spi0 aliases.
 - Fix the pinctrl-names of mmc0 node.
 - Add the "u-boot,dm-pre-reloc" property to determine which nodes
   are used by the board_init_f stage.
 - Fix the compilation warnings.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

ARM: dts: at91: Add dts files for at91sam9x5ek

The device tree source files of at91sam9x5ek board are copied from
the Linux v4.10, do the changes below.
 - Add the reg property for the pinctrl node.
 - Move the gpio (pioA, pioB, pioC ...) nodes as the pinctrl's
   slibling nodes, instead of the child nodes.
 - Add the "u-boot,dm-pre-reloc" property to determine which nodes
   are used by the board_init_f stage.
 - Change the compatible of the spi flash to "spi-flash".
 - Add the spi0 aliases.
 - Fix the compilation warnings.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

serial: atmel_usart: Add clk support

Add the clock support.
Note that the clock handling of the DBGU peripheral is different
from the USART.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

serial: atmel_usart: Fix early debug not work in SPL

Add the uart init function to be used on both probe and the early
debug uart init. For the latter, the input clock should be from
CONFIG_DEBUG_UART_CLOCK.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

clk: at91: Align the at91 pmc's compatibles

Align the at91 pmc's compatibles with kernel.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Andreas Bießmann <[email protected]>

clk: at91: Align clk-master compatibles with kernel

Add the compatible "atmel,at91rm9200-clk-master" to align with
the kernel.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

clk: at91: Enhance the peripheral clock

Enhance the peripheral clock to support both at9sam9x5's and
at91rm9200's peripheral clock via the different compatibles.

Signed-off-by: Wenyou Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>

net: macb: Align the compatibles with kernel

Add the compatibles to align with the kernel.

Signed-off-by: Wenyou Yang <[email protected]>
Acked-by: Joe Hershberger <[email protected]>

net: macb: Add remove callback

To avoid the failure of mdio_register(), add the remove callback
to unregister the mii_dev when removing the ethernet device.

Signed-off-by: Wenyou Yang <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
Fixed up unused variable warning, e.g. for gurnard:
Signed-off-by: Simon Glass <[email protected]>

configs: sama5d3xek: add default config for CMP board

The sama5d36ek CMP board is the variant of sama5d3xek board.
It is equipped with the low-power DDR2 SDRAM, PMIC ACT8865, and
some power rails. The board is mainly used to measure the power
consumption. As all those changes are done in at91bootstrap,
in U-Boot, only use another device tree file, no code needed
to change.

As there is additional power consumption when enbling the USB
Host and USB device, for the power consumption measurement
intention, disable the USB host and device.

Signed-off-by: Wenyou Yang <[email protected]>

board: sama5d4ek: fix DD2 configuration

Fix the DDR2 configuration to make SPL work.

Signed-off-by: Wenyou Yang <[email protected]>

configs: sama5d2_xplained: update for SPL

Enable config options to support the SPL, increase the malloc
memory size for the SPL and board_init_f stage and increase
the memory space for the SPL binary.

Signed-off-by: Wenyou Yang <[email protected]>

board: sama5d2_xplained: remove unnecessary header files

Remove the unnecessary header files.

Signed-off-by: Wenyou Yang <[email protected]>

board: sama5d2_xplained: remove uart1 init

Due to the pin configuration and clock enabling is handling by the
driver, remove the unneeded hardcode uart1 init during
board_early_init_f stage.

Signed-off-by: Wenyou Yang <[email protected]>

board: sama5d2_xplained: clean up macb init code

Because the MACB driver supports the driver model and device tree,
the pins configuration and clock enabling are handled by the
pinctrl driver and clock driver, remove this hardcoded init code.

The USB Ether init code is removed as well.

Signed-off-by: Wenyou Yang <[email protected]>

configs: sama5d2_xplained: enable CONFIG_DM_ETH

Enable CONFIG_DM_ETH to make MACB to support driver model.

Because the USB Ether doesn't support driver model so far,
remove this feature.

Signed-off-by: Wenyou Yang <[email protected]>

ARM: dts: sama5d2_xplained: update for SPL

Add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.

Signed-off-by: Wenyou Yang <[email protected]>

ARM: dts: sama5d2: add clock property for uart1 node

Add clock property for uart1 node.

Signed-off-by: Wenyou Yang <[email protected]>

Merge branch 'master' of git://git.denx.de/u-boot-i2c

p1_p2_rdb: Fix unused variable warning

With gcc-6 we see a warning that sysclk_tbl is defined but unused, so
remove it.

Cc: York Sun <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: York Sun <[email protected]>

dm: Update Simple Watchdog uclass

- Remove "probe" function from sandbox wdt driver
- Fix include order

Fixes: 0753bc2d30d7 ("dm: Simple Watchdog uclass")
Signed-off-by: Maxim Sloyko <[email protected]>
[trini: Create as the delta between v1 (applied) and v2 (should have
 applied)].
Signed-off-by: Tom Rini <[email protected]>

ARM: mvebu: switch db-88f6820-amc to DM for i2c

Move existing configuration from header file to defconfig or dts as
appropriate.

Signed-off-by: Chris Packham <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>

arm64: mvebu: Fix the bubt comamnd NAND device support

Fix the NAND structures in bubt command according to latest
changes in MTD API.

Signed-off-by: Konstantin Porotchkin <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Igal Liberman <[email protected]>
Cc: Nadav Haklai <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>

fix: nand: pxa3xx: Remove hardcode values from the driver

Obtain NAND controller setup parameters from the device
tree instead of using hardcoded values.

Signed-off-by: Konstantin Porotchkin <[email protected]>
Cc: Scott Wood <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Igal Liberman <[email protected]>
Cc: Nadav Haklai <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>

fix: phy: marvell: cp110: pcie: update analog parameters according to latest ETP

Add PCIE analog parameters initialization values according to
latest ETP.

Signed-off-by: Igal Liberman <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>

fix: phy: marvell: cp110: rename comphy_index to cp_index

No functional change.
The variable name "comphy_index" is misleading, it represents
cp index and not comphy index.

Signed-off-by: Igal Liberman <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>

fix: phy: marvell: cp110: sfi: update analog parameters according to latest ETP

Add SFI analog parameters initialization values according to
latest ETP.

Signed-off-by: Igal Liberman <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>

phy: marvell: print comphy status even when it's disconnected

since now the COMPHY can also be ignored, we must know the
state of the COMPHY. we cannot assume anymore that a missing
COMPHY is unconnected.

Signed-off-by: Yehuda Yitschak <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
Signed-off-by: Igal Liberman <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>

fix: phy: marvell: cp110: fix comphy lane 4 selection options

The comphy configuration is incorrect.
Set the correct values for SGMII.

In addition, remove xaui from the comment as it is not supported.

Signed-off-by: Yoav Gvili <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
Signed-off-by: Igal Liberman <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>

phy: marvell: cp110: add 5G XFI mode

This patch adds the option to configure a comphy to 5G XFI mode.

In order to configure the comphy to 5G XFI, update
the comphy node in the device-tree:
phy2 {
phy-type = <PHY_TYPE_SFI>;
phy-speed = <PHY_SPEED_5_15625G>;
};

Signed-off-by: Igal Liberman <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>

fix: phy: marvell: cp110: update comphy selector option

Align PHY selectors register with Armada-CP-110 functional SPEC
update all relevant device trees with this change.

Signed-off-by: Hanna Hawa <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
Signed-off-by: Igal Liberman <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>

fix: phy: marvell: cp110: sata: update analog parameters according to latest ETP

Add SATA analog parameters initialization values according to
latest ETP.

Signed-off-by: Konstantin Porotchkin <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
Signed-off-by: Igal Liberman <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>

fix: phy: marvell: cp110: fix the KR/SFI line 4 selector

This patch fixes the following:
1. KR/SFI on lane #4 mux selector is 0x2 and not 0x1
2. Comment typo

Signed-off-by: Rabeeh Khoury <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
Signed-off-by: Igal Liberman <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>

phy: marvell: add IGNORE COMPHY type

This type tells u-boot to preserve the COMPHY settings as is
it is usefull in situations where the COMPHY was initialized by
earlier firmware.
Note that IGNORE is different from UNCONNECTED since setting
UNCONNECTED type will disconnect the COMPHY in the COMPHY MUX
which is a desired behaviour

Signed-off-by: Yehuda Yitschak <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
Signed-off-by: Igal Liberman <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>

phy: marvell: cp110: update utmi phy connection type

UTMI_PHY_TO_USB_HOST was used in USB3 UTMI dts node only, but there will
be USB2 UTMI dts node for some SoCs that have got USB2 controller, so rename
TO_USB_HOST to TO_USB3_HOST to distinguish TO_USB2_HOST in later on patches.

Signed-off-by: zachary <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
Signed-off-by: Igal Liberman <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>

phy: marvell: cp110: add support for end point configuration

The serdes was always configured in root complex mode.
this patch add new entry in device tree (per serdes)
which indicates whether the serdes is in end point mode.
if so, it skips the root complex configuration.

Signed-off-by: Haim Boot <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
Signed-off-by: Igal Liberman <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>

phy: marvell: Replace PHY_TYPE_KR with PHY_TYPE_SFI

Use correct naming as done in the latest Marvell U-Boot version as well.

Signed-off-by: Stefan Roese <[email protected]>
Signed-off-by: Igal Liberman <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>

fix: mvebu_ comphy: Update COMPHY sequence number

Use local static counter for maintaining the COMPHY chip-ID
upon its initialization.
The dev->seq originally used as the COMPHY chip-ID depends
on the device tree scan order and produces wrong results
that breaks the deficated PHYs init flow, which in turn
breaks the USB support.

Change-Id: I4e3f7ec36590a7f95dc94d9269a3c47fb708c4a9
Signed-off-by: Konstantin Porotchkin <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Igal Liberman <[email protected]>
Cc: Stefan Chulski <[email protected]>
Cc: Nadav Haklai <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>

arm: mvebu: Minor fixes in the AXP / A38x SERDES code

- Fix spelling error of SERDES_VERSION
- Remove superfluous definition of this macro
- Remove unnecessary include of i2c.h

Signed-off-by: Uwe Kleine-König <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>

arm64: mvebu: a8k: Add NAND configuration parameters

Add NAND configuration parameters to A8K shared config file.
Add defconfig for db-88f7040 board with boot from NAND setup.

Signed-off-by: Konstantin Porotchkin <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Igal Liberman <[email protected]>
Cc: Nadav Haklai <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>

arm64: a8k: dts: Add support for NAND devices on A8K platform

Add NAND to CP master device tree. Add armada-7040-db-nand
device tree for the board configured with NAND boot device.
Add comment about boot device ID to armada-7040-db DTS.

Signed-off-by: Konstantin Porotchkin <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Igal Liberman <[email protected]>
Cc: Nadav Haklai <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>

arm64: mvebu: a8k: Add support for NAND clock get

Implement mvebu_get_nand_clock call for A8K family.
This function is used by PXA3XX NAND driver.

Signed-off-by: Konstantin Porotchkin <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Igal Liberman <[email protected]>
Cc: Nadav Haklai <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>

arm64: mvebu: Trigger PCI devices scan at early init stage

Add PCIe initialization at early init stage.
This operation has a side effect of detecting all PCIe
plug-in cards, so the operator is not obligated to issue
"pci enum" command though CLI for this purpose.

Signed-off-by: Konstantin Porotchkin <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Igal Liberman <[email protected]>
Cc: Nadav Haklai <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>

mvebu: dts: a80x0: Sync the DB DTS with standard config A

Sync the default configuration of Armada-8040-DB with
Marvell u-boot-2015  standard configuration "A" for the same board.
The standard configuration "A" enables 2 PCIe slots on CP0
and 3 PCIe slots on CP1.
This is the main configuration used for u-boot  and Linux tests.
This patch also re-arranges the DTS file entries by grouping
all nodes related to CP0 and CP1.

Signed-off-by: Konstantin Porotchkin <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Igal Liberman <[email protected]>
Cc: Nadav Haklai <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>

fix: mvebu: pcie_dw: Allow probing empty PCIe slots

This patch allows probing all PCIe nodes defined in DTS
even if there no device connected to such node (no link).
Without this fix the driver returns -ENODEV when the PCIe
link is down. As result the pci_init function stops
scanning bus on first empty PCIe slot and all devices
located in higher numbered buses are not discovered.

Signed-off-by: Konstantin Porotchkin <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Igal Liberman <[email protected]>
Cc: Nadav Haklai <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>

net: mvpp2: Add remove function that is called before the OS is started

This patch adds a remove function to the mvpp2 ethernet driver which is
called before the OS is started, doing:

- Allocate the used buffers back from the buffer manager
- Stop the BM activity

Signed-off-by: Stefan Roese <[email protected]>
Cc: Stefan Chulski <[email protected]>
Cc: Kostya Porotchkin <[email protected]>
Cc: Nadav Haklai <[email protected]>
Acked-by: Joe Hershberger <[email protected]>

ARM: keystone: Enable DM_I2C by default

Enable by default DM_I2C for all Texas Instruments Keystone 2 based
evms.

Signed-off-by: Franklin S Cooper Jr <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>