Hayes Wang [Wed, 16 Dec 2020 09:03:23 +0000 (17:03 +0800)]
eth/r8152: fix the aggregation issue
Remove the redundant setting for USB_RX_EARLY_SIZE. Besides, for
RTL8153B, it is necessary to notify the hardware of the changes
of the aggregation settings.
Ran Wang [Wed, 18 Nov 2020 07:49:02 +0000 (15:49 +0800)]
usb: xhci: fix lack of short packet event trb handling
For bulk IN transfer, the codes will set ISP flag to request event TRB
being generated by xHC for the case of short packet. So when encountering
buffer-cross-64K-boundary (which we will divide payload and enqueuqe
more than 1 transfer TRB), and the first TRB ends up with a short packet
condition it will trigger an short packet code transfer event per that
flag and cause more than 1 event TRB generated for this transfer.
However, current codes will only handle the first transfer event TRB
then mark current transfer completed, causing next transfer
failure due to event TRB mis-match.
Such issue has been observed on some Layerscape platforms (LS1028A,
LS1088A, etc) with USB ethernet device.
This patch adds a loop to make sure the event TRB for last transfer TRB
has been handled in time.
Andy Shevchenko [Thu, 3 Dec 2020 15:40:11 +0000 (17:40 +0200)]
x86: edison: BINMAN selection is specific to the board
The platforms based on Intel Tangier may have different requirements
how to create bootloader bundle to supply to a device. Currently
the BINMAN approach is for Intel Edison only.
Andy Shevchenko [Fri, 27 Nov 2020 12:40:48 +0000 (14:40 +0200)]
x86: tangier: Find proper memory region for relocation
It appears that U-Boot works by luck on Intel Edison board because the amount
of RAM is less than 1 GB and standard way of calculating the top of it work
for this configuration. However, this won't work if the amount of RAM is
different and split differently in address space. We have to find the suitable
window correctly.
Find proper memory region for relocation by scanning MMAP SFI table in
board_get_usable_ram_top() callback.
According to the address map documentation the Main Memory is guaranteed to lie
in the 0..2 GB range, that's why we limit search by this range.
Fixes: e71de54a4943 ("x86: Add Intel Tangier support") Signed-off-by: Andy Shevchenko <[email protected]> Reviewed-by: Simon Glass <[email protected]> Reviewed-by: Bin Meng <[email protected]>
[bmeng: fixed a typo in the commit message] Signed-off-by: Bin Meng <[email protected]>
Simon Glass [Mon, 9 Nov 2020 14:12:24 +0000 (07:12 -0700)]
x86: zimage: Update cmdline parameter to be an env var
With the updated changes to bootargs substitution[1], the zboot command
needs to be updated to get its command line from an environment variable
instead of a memory address. This is because the command-line string must
be updated to convert %U to ${uuid}, etc.
In any case it is more flexible to use a environment variable and it is
best to do this before the release to avoid a subsequent change.
Tom Rini [Tue, 15 Dec 2020 18:57:03 +0000 (13:57 -0500)]
Merge tag 'doc-2021-01-rc4' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Documentation fixes for v2020.01-rc4
Move several README files to reStructured text for the HTML documentation.
Describe register for global data on x86.
Allow building HTML documentation with Sphinx 3
Igor Opaniuk [Thu, 29 Oct 2020 10:59:19 +0000 (12:59 +0200)]
distro_bootcmd: set devtype for dhcp boot
Set $devtype for DHCP boot, which can be handy for the boot.scr
for detection of devtype used (for example, when the same boot.scr is
used for both mmc/dhcp boot):
- Fix wrong amoswap t1 usage in startup.
- Reset the board after crash.
- Enable distro booting from an attached SCSI disk for QEMU.
- Support the optional header fields in efi header.
Marek Szyprowski [Mon, 14 Dec 2020 11:34:19 +0000 (12:34 +0100)]
usb: dwc3-meson-g12a: always configure dr-mode
dwc3_meson_g12a_force_mode() sets the dr-mode of the USB PHY. However
it skips setting the mode if it matches the one done during driver probe
(stored in private structure). This fails if the mode has been changed
to other value and then back to initial one. Fix this by configuring the
dr-mode always, regadless of the one set at the driver probe).
This fixes operation of USB gadget based drivers when they are initialized
for the second time.
Modify the size of the Optional Header "Windows-Specific Fields" to fit with the specification.
(https://docs.microsoft.com/en-us/windows/win32/debug/pe-format)
Atish Patra [Tue, 13 Oct 2020 19:23:31 +0000 (12:23 -0700)]
riscv: Fix efi header for RV32
RV32 should use PE32 format instead of PE32+ as the efi header format.
This requires following changes
1. A different header magic value
2. An additional parameter known as BaseOfData. Currently, it is set to
zero in absence of any usage.
If an exception occurs on ARM or x86, we call panic() which will try to
reset the board. Do the same on RISC-V.
To avoid -Werror=format-zero-length move a '\n' to the string passed to
panic. We don't need a message here as depending on CONFIG_PANIC_HANG we
will either see
Tom Rini [Fri, 11 Dec 2020 20:55:17 +0000 (15:55 -0500)]
Merge tag 'u-boot-atmel-fixes-2021.01-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel fixes for 2021.01 cycle
This set includes very important fixes for: MMC booting on several
boards, drive strength on sam9x60ek mmc lines, compile issues for
timer.c old driver, removal of unwanted access to sam9x60 bit for
oscillator bypass mode, and eeproms read on sama5d2_icp.
arm: ls102xa: select USB PHY erratum's only if USB is enabled
The USB support is not by default enabled on all designs, so it does not
make seance to have USB specific erratum's enabled on such a designs.
On our internal Hitachi-Powergrids design not using the USB controller
there is a crash when accessing those specific memory locations selected
by the erratum flags.
Chris Packham [Thu, 3 Dec 2020 03:24:29 +0000 (16:24 +1300)]
powerpc: mpc85xx: Allow boards to override CONFIG_USB_MAX_CONTROLLER_COUNT
If the board isn't strapped to enable USB1 then attempting to access it
will result in a hang. Avoid this by allowing boards to define
CONFIG_USB_MAX_CONTROLLER_COUNT.
Alban Bedel [Tue, 17 Nov 2020 15:20:04 +0000 (16:20 +0100)]
armv8: fsl-layerscape: Fix automatic setting of bootmcd with TF-A
When booting from TF-A there is a logic that attempt to detect if the
default environment is used, if this is the case it then set the
`bootcmd` and `mcinitcmd` depending of the device we booted from.
This detection logic is dubious as it access internals of the env
implementation and it doesn't always work correctly.
First of all it detect any valid environment as not being the
default, so after running `env default -a && saveenv` the board
doesn't boot anymore as `bootcmd` is then empty.
But it also fails in some other ways, for example it always detect a
default environment when redundant env is enabled on MMC, so in that
case `bootcmd` is overwritten on every boot.
Instead of increasing the complexity of the detection just check if
`bootcmd` and `mcinitcmd` are set in the environment and set them if
they are not.
armv8: lx2162a: Add Soc changes to support LX2162A
LX2162 is LX2160 based SoC, it has same die as of LX2160
with different packaging.
LX2162A support 64-bit 2.9GT/s DDR4 memory, i2c, micro-click module,
microSD card, eMMC support, serial console, qspi nor flash, qsgmii,
sgmii, 25g, 40g, 50g network interface, one usb 3.0 and serdes
interface to support three PCIe gen3 interface.
Tom Rini [Wed, 9 Dec 2020 16:36:41 +0000 (11:36 -0500)]
Merge tag 'u-boot-stm32-20201209' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Manage CONFIG_ENV_EXT4_DEVICE_AND_PART in stm32mp1 board
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
The STM32MP1 DHCOM SoM can be built with either bus voltage level shifter
or without one on the SDMMC1 interface. Because the SDMMC1 interface is
limited to 50 MHz and hence SD high-speed anyway, disable the SD feedback
clock to permit operation of the same U-Boot image on both SoM with and
without voltage level shifter.
Marek Vasut [Tue, 1 Dec 2020 10:29:17 +0000 (11:29 +0100)]
ARM: dts: stm32: Enable internal pull-ups for SDMMC1 on DHCOM SoM
The default state of SD bus and clock line is logical HI. SD card IO is
open-drain and pulls the bus lines LO. Always enable the SD bus pull ups
to guarantee this behavior on DHCOM SoM. Note that on SoMs with SD bus
voltage level shifter, the pull ups are built into the level shifter,
however that has no negative impact.
- Espressobin: Simplify DT handling of board variants (Pali)
- Add Luka Perkov to maintainers of Puzzle-M801 (Luka)
- Armada 38x: Enable board specific USB2 high-speed impedance
threshold configuration (Joshua)
Claudiu Beznea [Wed, 2 Dec 2020 11:39:33 +0000 (13:39 +0200)]
clk: at91: sam9x60: remove the parsing of atmel, main-osc-bypass
Remove the parsing of atmel,main-osc-bypass DT property as the SAM9X60
have no support for crystal oscillator bypass. Setting this bit might
affect the device functionality.
Fixes: a64862284f65 ("clk: at91: sam9x60: add support compatible with CCF") Signed-off-by: Claudiu Beznea <[email protected]>
Pali Rohár [Wed, 25 Nov 2020 18:20:09 +0000 (19:20 +0100)]
arm: mvebu: Espressobin: Add support for emmc into dts file
To simplify setup, configuration and compilation of u-boot, define emmc
node for all Espressobin boards. Espressobin boards without populated emmc
works correctly, just detection and initialization of emmc obviously fails.
Code for emmc is extracted from commit f1a43c84a960 ("arm64: dts: a3720:
add support for espressobin with populated emmc").
Hardware testing of a board using the Armada 385 has shown that an
impedance threshold setting of 0x7 performs better in an eye-diagram
test than with Marvell's recommended value 0x6.
As other boards may still perform better with Marvell's reccomended value,
a configuration option is added with a default value of 0x6.
projects / J-u-boot.git / log