Bin Meng [Sun, 17 Jun 2018 12:57:49 +0000 (05:57 -0700)]
x86: qemu: Change default vesa mode to 1024x768x32
The default vesa mode was changed since commit 55b4e1b7d999
("x86: Change default FRAMEBUFFER_VESA_MODE of some boards") for
better VxWorks compatibility but with the changes QEMU video console
no longer works. This is because QEMU's vgabios implements the VESA
mode 8:8:8 as 24bpp without an alpha channel, which U-Boot's video
console driver currently does not support yet.
We need change to real 32bpp in order to make it work again. QEMU
vgabios implements the custom 32bpp VESA mode starting from 0x140
(320x200x32) to 0x147 (1600x1200x32). Set it to 0x144 (1024x768x32).
Fixes: 55b4e1b7d999 ("x86: Change default FRAMEBUFFER_VESA_MODE of some boards") Signed-off-by: Bin Meng <[email protected]> Reviewed-by: Simon Glass <[email protected]>
Chris Packham [Thu, 7 Jun 2018 08:45:06 +0000 (20:45 +1200)]
patman: add option for limiting the Cc list
Many mailing-lists consider a long Cc list a sign of spam and will
either drop the message or mark it for moderation. Because patman
automatically invokes get_maintainer.pl the Cc list can expand
unexpectedly. Allow the user to specify a limit for the Cc list.
This limit is applied after removing any known bouncing addresses. By
default no limit is applied.
Masahiro Yamada [Tue, 19 Jun 2018 07:11:45 +0000 (16:11 +0900)]
serial: uniphier: set clock rate without clock-frequency property
In Linux, the clock rate of the UART is given by the clock driver.
If you try to follow that in U-Boot, you would end up with adding
more u-boot,dm-pre-reloc properties, and also the clock driver would
be too big for SPL, which is used for UniPhier ARMv7 platform.
The current solution is to add 'clock-frequency' property to the
UART nodes, but it does not exist in the DT files in Linux. I do
not want to let DT diverge for U-Boot.
Check the SoC compatible and set the clock rate according to it.
This will be helpful to sync DT between Linux and U-Boot.
Masahiro Yamada [Tue, 19 Jun 2018 07:11:42 +0000 (16:11 +0900)]
ARM: uniphier: enable CONFIG_SNI_AVE and disable CONFIG_SMC911X
Enable the on-chip ethernet driver for uniphier_{v7,v8}_defconfig.
Disable the on-board SMC911x because it has not migrated to the
driver model yet - it is not possible to enable DM and non-DM
drivers at the same time.
The CONFIG_SMC911X for uniphier_ld4_sld8_defconfig is still kept
because the on-chip ethernet driver for LD4, sLD8 is not supported
yet.
Tom Rini [Fri, 22 Jun 2018 12:14:49 +0000 (08:14 -0400)]
Merge tag 'signed-efi-2018.07' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-06-21
A single urgent fix to make sure green and red are not swapped
in OSs that make use of EFI GOP frame buffers to display pictures
(such as efifb in Linux).
Alexander Graf [Tue, 19 Jun 2018 11:34:54 +0000 (13:34 +0200)]
efi_loader: Fix GOP 32bpp exposure
We store pixels as BGRA in memory, as can be seen from struct efi_gop_pixel.
So we need to expose the same format to UEFI payloads to actually have them
use the correct colors.
Tom Rini [Wed, 20 Jun 2018 03:53:54 +0000 (23:53 -0400)]
Makefile: Ensure we build with -std=gnu11
As many targets are now commonly built with gcc-6 or later (which
defaults to a newer C standard than older compilers), certain C
constructs are now being used as they produce more readable code. And
while all compilers that we support building with support the C11
standard (and GNU11) they do not default to that standard. Ensure that
we pass along -std=gnu11 when building.
Neil Armstrong [Thu, 14 Jun 2018 11:43:37 +0000 (13:43 +0200)]
adc: meson-saradc: fix regmap_init_mem call
The SARADC driver was merged after the following commit :
commit d35812368a59 ("regmap: change regmap_init_mem() to take ofnode instead udevice")
Thus breaking build, this patch fixes the regmap_init_mem accordingly.
Michal Simek [Wed, 13 Jun 2018 06:56:31 +0000 (08:56 +0200)]
common: Fix cpu nr type which is always unsigned type
cpu_cmd() is reading cpu number via simple_strtoul() which is always
unsigned type.
Platform code implementations are not expecting that nr can be negative
and there is not checking in the code for that too.
This patch is using u32 type for cpu number to make sure that platform
code get proper value range.
Marek Vasut [Wed, 13 Jun 2018 04:13:33 +0000 (06:13 +0200)]
bootm: Handle kernel_noload on arm64
The ARM64 has 2 MiB alignment requirement for the kernel. When using
fitImage, this requirement may by violated, the kernel will thus be
executed from unaligned address and fail to boot. Do what booti does
and run booti_setup() for kernel_noload images on arm64 to obtain a
suitable aligned address to which the image shall be relocated.
Marek Vasut [Wed, 13 Jun 2018 04:13:32 +0000 (06:13 +0200)]
ARM: image: Add option for ignoring ep bit 3
Add option to the booti_setup() which indicates to it that the caller
requires the image to be relocated to the beginning of the RAM and
that the information whether the image can be located anywhere in RAM
at 2 MiB aligned boundary or not is to be ignored. This is useful ie.
in case the Image is wrapped in another envelope, ie. fitImage and not
relocating it but moving it would corrupt the envelope.
Simon Glass [Tue, 12 Jun 2018 06:04:59 +0000 (00:04 -0600)]
fdtgrep: Separate out checking of two allocations
The current code might succeed on the first allocation and fail on the
second. Separate the checks to avoid this problem.
Of course, free() will never fail and the chances that (when allocating
two small areas) one will succeed and one will fail are just as remote.
But this keeps coverity happy.
Reported-by: Coverity (CID: 131226) Signed-off-by: Simon Glass <[email protected]>
Simon Glass [Tue, 12 Jun 2018 06:04:58 +0000 (00:04 -0600)]
fdtgrep: Fix logic of free() in do_fdtgrep()
This loop never actually exits, but the way the code is written this is
not obvious. Add an explicit error check.
Reported-by: Coverity (CID: 131280) Signed-off-by: Simon Glass <[email protected]>
[trini: Add explicit init of region to NULL per LLVM warning] Signed-off-by: Tom Rini <[email protected]>
Marek Vasut [Mon, 18 Jun 2018 02:09:10 +0000 (04:09 +0200)]
ARM: dts: rmobile: Move the PHY reset GPIOs into PHY nodes
Both the RAVB and SH ether driver now support parsing the PHY reset
GPIOs from both the PHY nodes and the MAC nodes, move the reset GPIOs
back into the PHY nodes to minimize DT difference between U-Boot and
Linux.
Marek Vasut [Mon, 18 Jun 2018 02:03:01 +0000 (04:03 +0200)]
net: sh_eth: Support reset GPIO both in mac and phy node
The recent DTs have the PHY reset GPIO in the PHY node rather than
the ethernet MAC node, support extracting the PHY reset GPIO info
from both the PHY node and ethernet MAC node.
Marek Vasut [Mon, 18 Jun 2018 02:02:15 +0000 (04:02 +0200)]
net: ravb: Support reset GPIO both in mac and phy node
The recent DTs have the PHY reset GPIO in the PHY node rather than
the ethernet MAC node, support extracting the PHY reset GPIO info
from both the PHY node and ethernet MAC node.
Marek Vasut [Mon, 18 Jun 2018 03:44:53 +0000 (05:44 +0200)]
net: ravb: Filter out supported PHY features
The RAVB only supports 100Full and 1000Full operation, it does not support
10Full or any Half-duplex modes. The PHY could still advertise those features
though, so filter out the PHY features accordingly.
Marek Vasut [Mon, 18 Jun 2018 07:35:45 +0000 (09:35 +0200)]
net: ravb: Do not shut down clock in start callback
Do not stop the clock in the start callback in case of failure, keep
them running to also keep the PHY running. The failure could be ie.
PHY failing to negotiate link and if the clock get shut down, another
attempt at bringing the link up would fail. The clock right now are
started in probe function and stopped in remove function, which is
the correct behavior.
Simon Glass [Tue, 12 Jun 2018 06:04:56 +0000 (00:04 -0600)]
console: Fix handling of NULL global_data
Both putc() and puts() can be called before global_data is set up. Some of
the code paths don't handle this correctly. Add an explicit test before
any member is accessed.
Adam Ford [Tue, 12 Jun 2018 01:05:38 +0000 (20:05 -0500)]
gpio: omap_gpio: Name GPIO's by bank and index with DM_GPIO
There are multiple GPIO banks with up to 32 pins / bank. When
using 'gpio status -a' to read the pins, this patch displays
both GPIO<bank>_<index> similar to how the device trees
display in addition to displaying gpio_#
Adam Ford [Tue, 12 Jun 2018 00:56:49 +0000 (19:56 -0500)]
arm: mach-omap2/omap3/clock.c: Enable all GPIO with CMD_GPIO
When CMD_GPIO is enabled the command 'gpio status -a' can cause
a hang or reboot if GPIO banks are not enabled, because it scans
all banks. This patch enables all GPIO banks so 'gpio status -a'
can fully execute.
Adam Ford [Mon, 11 Jun 2018 22:17:48 +0000 (17:17 -0500)]
block: Add SPL_BLOCK_CACHE and default n
When enabling BLOCK_CACHE on devices with limited RAM during SPL,
some devices may not boot. This creates an option to enable
block caching in SPL by defaults off. It is dependent on SPL_BLK
Fixes: 46960ad6d09b ("block: Have BLOCK_CACHE default to y in some cases") Signed-off-by: Adam Ford <[email protected]>
Andrew F. Davis [Mon, 11 Jun 2018 19:04:17 +0000 (14:04 -0500)]
arm: Do not clear LR on exception in SPL
When an exception or interrupt occurs the link register (LR) may
contain the source of the exception, although we do not print the
value it may still be extracted with a debugger. When in SPL we
loop on getting and exception, but use a linking branch, which
over-writes the LR value, use a regular branch instruction here.
Yevgeny Popovych [Mon, 11 Jun 2018 11:14:33 +0000 (14:14 +0300)]
fs: btrfs: Do not fail when all root_backups are empty
This is the case when reading freshly created filesystem.
The error message is like the following:
btrfs_read_superblock: No valid root_backup found!
Since the data from super_roots/root_backups is not actually used -
decided to rework btrfs_newest_root_backup() into
btrfs_check_super_roots() that will only check if super_roots
array is valid and correctly handle empty scenario.
As a result:
* btrfs_read_superblock() now only checks if super_roots array is valid;
the case when it is empty is considered OK.
* removed root_backup pointer from btrfs_info,
which would be NULL in case of empty super_roots.
* btrfs_read_superblock() verifies number of devices from the superblock
itself, not newest root_backup.
Ramon Fried [Fri, 8 Jun 2018 17:53:27 +0000 (20:53 +0300)]
iotrace: fix behaviour when buffer is full
Don't continue updating the offset when buffer is full.
When the buffer size exhausts and there's no space left to write
warn the user and update only the needed size and not both the
offset and needed size.
Add needed buffer size information in the iotrace command.
Igor Opaniuk [Sun, 3 Jun 2018 18:56:43 +0000 (21:56 +0300)]
doc: avb2.0: add README about AVB2.0 integration
Contains:
1. Overview of Android Verified Boot 2.0
2. Description of avb subset of commands
3. Examples of errors when boot/vendor/system/vbmeta partitions
are tampered
4. Examples of enabling AVB2.0 on your setup
Igor Opaniuk [Sun, 3 Jun 2018 18:56:42 +0000 (21:56 +0300)]
test/py: avb2.0: add tests for avb commands
1. Run AVB 2.0 full verification chain, avb verify
2. Check if 'avb get_uuid' works, compare results with
'part list mmc 1' output
3. Test `avb read` commands, which reads N bytes from a partition
identified by a name
Igor Opaniuk [Sun, 3 Jun 2018 18:56:39 +0000 (21:56 +0300)]
cmd: avb2.0: avb command for performing verification
Enable a "avb" command to execute Android Verified
Boot 2.0 operations. It includes such subcommands:
avb init - initialize avb2 subsystem
avb read_rb - read rollback index
avb write_rb - write rollback index
avb is_unlocked - check device lock state
avb get_uuid - read and print uuid of a partition
avb read_part - read data from partition
avb read_part_hex - read data from partition and output to stdout
avb write_part - write data to partition
avb verify - run full verification chain
Igor Opaniuk [Sun, 3 Jun 2018 18:56:38 +0000 (21:56 +0300)]
avb2.0: implement AVB ops
Implement AVB ops on top of existing mmc subsystem API. Currently there
is a full implementation of such operations, defined by [1]
AVB2.0 specification:
.read_from_partition() - reads N bytes from a partition identified by
a name.
.write_to_partition() - Writes N bytes to a partition identified by a name.
.validate_vbmeta_public_key() - checks if the given public ‘vbmeta’
partition is trusted.
.get_unique_guid_for_partition() - Gets the GUID for a partition identified
by a string name.
As [1] specification recommends to use tamper-evident storage for storing
rollback indexes and device state (LOCKED/UNLOCKED),
currently are only stubs instead of full implementation for these ops:
.read_rollback_index() - Gets the rollback index for a given index location
.write_rollback_index() - Sets the rollback index to a given location
.read_is_device_unlocked() - Gets where the device is unlocked
Igor Opaniuk [Sun, 3 Jun 2018 18:56:36 +0000 (21:56 +0300)]
avb2.0: add Android Verified Boot 2.0 library
Add libavb lib (3rd party library from AOSP), that implements support of
AVB 2.0. This library is used for integrity checking of Android partitions
on eMMC.
libavb was added as it is and minimal changes were introduced to reduce
maintenance cost, because it will be deviated from AOSP upstream in the future.
Changes:
- license headers changed to conform SPDX-style
- avb_crc32.c dropped
- updates in avb_sysdeps_posix.c/avb_sysdeps.h
Jon Nettleton [Thu, 7 Jun 2018 13:17:37 +0000 (16:17 +0300)]
mx6cuboxi: fix 4GB ddr memory detection
The soms with 4GB ddr have a rowaddr of 16 not 15, this allows
the detection mechanism to properly identify them as 4GB.
However these soms can be populated with whatever amount of
memory the customer requests therefor we need a ram stride test.
We can not use the get_ram_size() function because not all 4GB's
of DDR is addressable on a 32-bit architecture. Therefore instead
we use a memory stride of 128MB's and look for the address that
the memory wraps. This function is used for all som types to
catch most memory configurations.
This is a revised version of Rabeeh Khoury's original code.
Jon Nettleton [Thu, 7 Jun 2018 13:17:36 +0000 (16:17 +0300)]
mx6cuboxi: consolidate board detection and add som revision checking
In order to properly detect the board the checks need to be done
in a specific order. Move these tests back into a single enum
function that will always return the proper the board it is checking.
This also adds the best test we have for detecting the rev 1.5 som,
and it simplifies the device-tree filename building.
Mans Rullgard [Fri, 27 Apr 2018 09:45:15 +0000 (10:45 +0100)]
ARM: mxs: let boards override entire dram parameter table
If many values differ from the defaults, overriding the full table
is simpler and more space efficient than tweaking it through
mxs_adjust_memory_params().
Ye Li [Mon, 14 May 2018 12:44:29 +0000 (09:44 -0300)]
imx: Enable ACTLR.SMP bit for all i.MX cortex-a7 platforms
According to the Cortex-A7 TRM, for ACTLR.SMP bit "You must ensure this bit
is set to 1 before the caches and MMU are enabled, or any cache and TLB
maintenance operations are performed".
ROM sets this bit in normal boot flow, but when in serial download mode,
it is not set.
Here we add it in u-boot as a common flow for all i.MX cortex-a7 platforms,
including mx7d, mx6ul/ull and mx7ulp.
Signed-off-by: Ye Li <[email protected]>
[fabio: adapted to U-Boot mainline codebase and make checkpatch happy] Signed-off-by: Fabio Estevam <[email protected]>
projects / J-u-boot.git / log