include/configs/gw_ventana.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright (C) 2013 Gateworks Corporation
   4  */
   5
   6 #ifndef __CONFIG_H
   7 #define __CONFIG_H
   8
   9 /* SPL */
  10 /* Location in NAND to read U-Boot from */
  11 #define CONFIG_SYS_NAND_U_BOOT_OFFS     (14 * SZ_1M)
  12
  13 /* Falcon Mode */
  14 #define CONFIG_SYS_SPL_ARGS_ADDR        0x18000000
  15
  16 /* Falcon Mode - NAND support: args@17MB kernel@18MB */
  17 #define CONFIG_SYS_NAND_SPL_KERNEL_OFFS (18 * SZ_1M)
  18
  19 /* Falcon Mode - MMC support: args@1MB kernel@2MB */
  20 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR   0x800   /* 1MB */
  21 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS  (CONFIG_CMD_SPL_WRITE_SIZE / 512)
  22 #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x1000  /* 2MB */
  23
  24 #include "imx6_spl.h"                  /* common IMX6 SPL configuration */
  25 #include "mx6_common.h"
  26
  27 #define CONFIG_MACH_TYPE        4520   /* Gateworks Ventana Platform */
  28
  29 /* Serial ATAG */
  30 #define CONFIG_SERIAL_TAG
  31
  32 /* Size of malloc() pool */
  33 #define CONFIG_SYS_MALLOC_LEN           (10 * SZ_1M)
  34
  35 /* Serial */
  36 #define CONFIG_MXC_UART_BASE           UART2_BASE
  37
  38 #if !defined(CONFIG_SPI_FLASH) && defined(CONFIG_SPL_NAND_SUPPORT)
  39 /* Enable NAND support */
  40 #ifdef CONFIG_CMD_NAND
  41   #define CONFIG_SYS_MAX_NAND_DEVICE    1
  42   #define CONFIG_SYS_NAND_BASE          0x40000000
  43   #define CONFIG_SYS_NAND_5_ADDR_CYCLE
  44   #define CONFIG_SYS_NAND_ONFI_DETECTION
  45
  46   /* DMA stuff, needed for GPMI/MXS NAND support */
  47 #endif
  48
  49 #endif /* CONFIG_SPI_FLASH */
  50
  51 /* I2C Configs */
  52 #define CONFIG_SYS_I2C
  53 #define CONFIG_SYS_I2C_MXC
  54 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  55 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  56 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
  57 #define CONFIG_SYS_I2C_SPEED            100000
  58 #define CONFIG_I2C_GSC                  0
  59 #define CONFIG_I2C_EDID
  60
  61 /* MMC Configs */
  62 #define CONFIG_SYS_FSL_ESDHC_ADDR      0
  63
  64 /*
  65  * SATA Configs
  66  */
  67 #ifdef CONFIG_CMD_SATA
  68   #define CONFIG_SYS_SATA_MAX_DEVICE    1
  69   #define CONFIG_DWC_AHSATA_PORT_ID     0
  70   #define CONFIG_DWC_AHSATA_BASE_ADDR   SATA_ARB_BASE_ADDR
  71   #define CONFIG_LBA48
  72 #endif
  73
  74 /*
  75  * PCI express
  76  */
  77 #ifdef CONFIG_CMD_PCI
  78 #define CONFIG_PCI_SCAN_SHOW
  79 #define CONFIG_PCI_FIXUP_DEV
  80 #define CONFIG_PCIE_IMX
  81 #endif
  82
  83 /*
  84  * PMIC
  85  */
  86 #define CONFIG_POWER
  87 #define CONFIG_POWER_I2C
  88 #define CONFIG_POWER_PFUZE100
  89 #define CONFIG_POWER_PFUZE100_I2C_ADDR  0x08
  90 #define CONFIG_POWER_LTC3676
  91 #define CONFIG_POWER_LTC3676_I2C_ADDR  0x3c
  92
  93 /* Various command support */
  94
  95 /* Ethernet support */
  96 #define CONFIG_FEC_MXC
  97 #define IMX_FEC_BASE             ENET_BASE_ADDR
  98 #define CONFIG_FEC_XCV_TYPE      RGMII
  99 #define CONFIG_FEC_MXC_PHYADDR   0
 100 #define CONFIG_ARP_TIMEOUT       200UL
 101
 102 /* USB Configs */
 103 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET  /* For OTG port */
 104 #define CONFIG_MXC_USB_PORTSC     (PORT_PTS_UTMI | PORT_PTS_PTW)
 105 #define CONFIG_MXC_USB_FLAGS      0
 106 #define CONFIG_USBD_HS
 107
 108 /* Framebuffer and LCD */
 109 #define CONFIG_VIDEO_LOGO
 110 #define CONFIG_IMX_HDMI
 111 #define CONFIG_IMX_VIDEO_SKIP
 112 #define CONFIG_VIDEO_BMP_LOGO
 113 #define CONFIG_HIDE_LOGO_VERSION  /* Custom config to hide U-boot version */
 114
 115 /* Miscellaneous configurable options */
 116 #define CONFIG_HWCONFIG
 117
 118 /* Memory configuration */
 119
 120 /* Physical Memory Map */
 121 #define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
 122 #define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
 123 #define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
 124 #define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
 125
 126 #define CONFIG_SYS_INIT_SP_OFFSET \
 127         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 128 #define CONFIG_SYS_INIT_SP_ADDR \
 129         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 130
 131 /*
 132  * MTD Command for mtdparts
 133  */
 134
 135 /* Persistent Environment Config */
 136
 137 /* Environment */
 138 #define CONFIG_IPADDR             192.168.1.1
 139 #define CONFIG_SERVERIP           192.168.1.146
 140
 141 #define CONFIG_EXTRA_ENV_SETTINGS_COMMON \
 142         "pcidisable=1\0" \
 143         "splashpos=m,m\0" \
 144         "usb_pgood_delay=2000\0" \
 145         "console=ttymxc1\0" \
 146         "bootdevs=usb mmc sata flash\0" \
 147         "hwconfig=_UNKNOWN_\0" \
 148         "video=\0" \
 149         \
 150         "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
 151         "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
 152         "disk=0\0" \
 153         "part=1\0" \
 154         \
 155         "fdt_high=0xffffffff\0" \
 156         "fdt_addr=0x18000000\0" \
 157         "initrd_high=0xffffffff\0" \
 158         "fixfdt=" \
 159                 "fdt addr ${fdt_addr}\0" \
 160         "bootdir=boot\0" \
 161         "loadfdt=" \
 162                 "if ${fsload} ${fdt_addr} ${bootdir}/${fdt_file}; then " \
 163                         "echo Loaded DTB from ${bootdir}/${fdt_file}; " \
 164                         "run fixfdt; " \
 165                 "elif ${fsload} ${fdt_addr} ${bootdir}/${fdt_file1}; then " \
 166                         "echo Loaded DTB from ${bootdir}/${fdt_file1}; " \
 167                         "run fixfdt; " \
 168                 "elif ${fsload} ${fdt_addr} ${bootdir}/${fdt_file2}; then " \
 169                         "echo Loaded DTB from ${bootdir}/${fdt_file2}; " \
 170                         "run fixfdt; " \
 171                 "fi\0" \
 172         \
 173         "fs=ext4\0" \
 174         "script=6x_bootscript-ventana\0" \
 175         "loadscript=" \
 176                 "if ${fsload} ${loadaddr} ${bootdir}/${script}; then " \
 177                         "source ${loadaddr}; " \
 178                 "fi\0" \
 179         \
 180         "uimage=uImage\0" \
 181         "mmc_root=mmcblk0p1\0" \
 182         "mmc_boot=" \
 183                 "setenv fsload \"${fs}load mmc ${disk}:${part}\"; " \
 184                 "mmc dev ${disk} && mmc rescan && " \
 185                 "setenv dtype mmc; run loadscript; " \
 186                 "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \
 187                         "setenv bootargs console=${console},${baudrate} " \
 188                                 "root=/dev/${mmc_root} rootfstype=${fs} " \
 189                                 "rootwait rw ${video} ${extra}; " \
 190                         "if run loadfdt; then " \
 191                                 "bootm ${loadaddr} - ${fdt_addr}; " \
 192                         "else " \
 193                                 "bootm; " \
 194                         "fi; " \
 195                 "fi\0" \
 196         \
 197         "sata_boot=" \
 198                 "setenv fsload \"${fs}load sata ${disk}:${part}\"; " \
 199                 "sata init && " \
 200                 "setenv dtype sata; run loadscript; " \
 201                 "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \
 202                         "setenv bootargs console=${console},${baudrate} " \
 203                                 "root=/dev/sda1 rootfstype=${fs} " \
 204                                 "rootwait rw ${video} ${extra}; " \
 205                         "if run loadfdt; then " \
 206                                 "bootm ${loadaddr} - ${fdt_addr}; " \
 207                         "else " \
 208                                 "bootm; " \
 209                         "fi; " \
 210                 "fi\0" \
 211         "usb_boot=" \
 212                 "setenv fsload \"${fs}load usb ${disk}:${part}\"; " \
 213                 "usb start && usb dev ${disk} && " \
 214                 "setenv dtype usb; run loadscript; " \
 215                 "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \
 216                         "setenv bootargs console=${console},${baudrate} " \
 217                                 "root=/dev/sda1 rootfstype=${fs} " \
 218                                 "rootwait rw ${video} ${extra}; " \
 219                         "if run loadfdt; then " \
 220                                 "bootm ${loadaddr} - ${fdt_addr}; " \
 221                         "else " \
 222                                 "bootm; " \
 223                         "fi; " \
 224                 "fi\0"
 225
 226 #ifdef CONFIG_SPI_FLASH
 227         #define CONFIG_EXTRA_ENV_SETTINGS \
 228         CONFIG_EXTRA_ENV_SETTINGS_COMMON \
 229         "image_os=ventana/openwrt-imx6-imx6q-gw5400-a-squashfs.bin\0" \
 230         "image_uboot=ventana/u-boot_spi.imx\0" \
 231         \
 232         "spi_koffset=0x90000\0" \
 233         "spi_klen=0x200000\0" \
 234         \
 235         "spi_updateuboot=echo Updating uboot from " \
 236                 "${serverip}:${image_uboot}...; " \
 237                 "tftpboot ${loadaddr} ${image_uboot} && " \
 238                 "sf probe && sf erase 0 80000 && " \
 239                         "sf write ${loadaddr} 400 ${filesize}\0" \
 240         "spi_update=echo Updating OS from ${serverip}:${image_os} " \
 241                 "to ${spi_koffset} ...; " \
 242                 "tftp ${loadaddr} ${image_os} && " \
 243                 "sf probe && " \
 244                 "sf update ${loadaddr} ${spi_koffset} ${filesize}\0" \
 245         \
 246         "flash_boot=" \
 247                 "if sf probe && " \
 248                 "sf read ${loadaddr} ${spi_koffset} ${spi_klen}; then " \
 249                         "setenv bootargs console=${console},${baudrate} " \
 250                                 "root=/dev/mtdblock3 " \
 251                                 "rootfstype=squashfs,jffs2 " \
 252                                 "${video} ${extra}; " \
 253                         "bootm; " \
 254                 "fi\0"
 255 #else
 256         #define CONFIG_EXTRA_ENV_SETTINGS \
 257         CONFIG_EXTRA_ENV_SETTINGS_COMMON \
 258         \
 259         "image_rootfs=openwrt-imx6-ventana-rootfs.ubi\0" \
 260         "nand_update=echo Updating NAND from ${serverip}:${image_rootfs}...; " \
 261                 "tftp ${loadaddr} ${image_rootfs} && " \
 262                 "nand erase.part rootfs && " \
 263                 "nand write ${loadaddr} rootfs ${filesize}\0" \
 264         \
 265         "flash_boot=" \
 266                 "setenv fsload 'ubifsload'; " \
 267                 "ubi part rootfs; " \
 268                 "if ubi check boot; then " \
 269                         "ubifsmount ubi0:boot; " \
 270                         "setenv root ubi0:rootfs ubi.mtd=2 " \
 271                                 "rootfstype=squashfs,ubifs; " \
 272                         "setenv bootdir; " \
 273                 "elif ubi check rootfs; then " \
 274                         "ubifsmount ubi0:rootfs; " \
 275                         "setenv root ubi0:rootfs ubi.mtd=2 " \
 276                                 "rootfstype=ubifs; " \
 277                 "fi; " \
 278                 "setenv dtype nand; run loadscript; " \
 279                 "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \
 280                         "setenv bootargs console=${console},${baudrate} " \
 281                                 "root=${root} ${video} ${extra}; " \
 282                         "if run loadfdt; then " \
 283                                 "ubifsumount; " \
 284                                 "bootm ${loadaddr} - ${fdt_addr}; " \
 285                         "else " \
 286                                 "ubifsumount; bootm; " \
 287                         "fi; " \
 288                 "fi\0"
 289 #endif
 290
 291 #define CONFIG_BOOTCOMMAND \
 292         "for btype in ${bootdevs}; do " \
 293                 "echo; echo Attempting ${btype} boot...; " \
 294                 "if run ${btype}_boot; then; fi; " \
 295         "done"
 296
 297 #endif                         /* __CONFIG_H */